P
PrintablesGyronictonic
M8 to M6 Hex Nut Reducer
A nut reducer for the PB LC (Might work for other printers) Category: 3D Printer Accessories
- Pobrania
- 41
- Polubienia
- 1
- Ocena
- 0
Wszystkie modele
Liczymy pasujące modele…
P
PrintablesGyronictonic
Paintball Speed Feed for the Rotor - Mould cavity
Made a mould cavity of a generic speed feed for my rotor. A silicone mix is poured into the cavity, creating a cast of the speed feed. Find a silicone mix with a shore hardness of 40 which is as strong as a pencil eraser. Solidworks 2012…
- Pobrania
- 37
- Polubienia
- 6
- Ocena
- 0
P
PrintablesGyronictonic
V-tail Frame for the Hubsan X4 Quadcopter
V-Tail quad-copter frame using the Hubsan X4 board. All motors were upgraded to 8.5mm coreless motors. It has a very sharp and responsive Yaw control. Stock props can provide enough lift but only at 80% throttle. Exchanging the back stock…
- Pobrania
- 32
- Polubienia
- 9
- Ocena
- 0
P
PrintablesGyronictonic
3DPrintMi - Print. Make. Innovate.
Gada Prize Bronze Medalist 3DPrintMi combines the minimalistic, open frame style of the Printrbot/Wallace with the fixed Y Gantry system of the Mendel. The printed parts are designed to be produced rapidly, efficiently and assembled…
- Pobrania
- 17
- Polubienia
- 1
- Ocena
- 0
P
PrintablesGyronictonic
Printrbot LC and LC+: Y Bearing Guide for GT2 32 teeth pulleys
Upgraded to the Gt2 32 teeth pulleys and only to realized they don't fit at all. Designed a new Y bearing guide that offsets the 608 bearings back a few to make everything fit. By all means, go for a 18 or 25 teeth instead, don't make the…
- Pobrania
- 16
- Polubienia
- 1
- Ocena
- 0
P
PrintablesGyronictonic
Aluminum 3DPrintMi
The Aluminum 3DPrintMi is the next iteration of my previous design, 3DPrintMi. The frame was redesigned to use the commonly available aluminum extrusion 2020, reducing the assembly time and part count while boosting frame rigidity.…
- Pobrania
- 13
- Polubienia
- 1
- Ocena
- 0
P
PrintablesGyronictonic
Spring-loaded Replicator 1 Drive Block - Modified Lever
Derivation of the "Spring-loaded Replicator 2 Drive Block" by Makerbot Modified the MBE Lever to use a M3 x 8mm screw to hold the 623ZZ bearing. This was done because I had an issue printing the bearing bolt stub, either being too weak to…
- Pobrania
- 12
- Polubienia
- 2
- Ocena
- 0
P
PrintablesGyronictonic
Direct Drive Vert-Xtruder
Overview A Direct Drive Extruder with the Nema17 motor positioned parallel to the X Axis, suitable for printers with a vertical X configuration. It is used on my RepRap 3Dprinter, 3DPrintMi http://www.thingiverse.com/thing:95339…
- Pobrania
- 9
- Polubienia
- 3
- Ocena
- 0
P
PrintablesGyronictonic
Heart Marriage Equality
If you support marriage equality, print one now! Downloaded a heart from grabcad.com, made some edits and came up with this. http://grabcad.com/library/heart-in-heart Instructions Scale up to whatever size. 150% should give you 42mm wide…
- Pobrania
- 8
- Polubienia
- 2
- Ocena
- 0
P
PrintablesGyronictonic
Printrbot LC Single Universal Extruder Mount
Designed an extruder mount for the new Universal Extruder from this kickstarter project http://www.kickstarter.com/projects/qu-bd/open-source-universal-3d-printer-extruder-dual-ext There are some issues with this mount. One is that the…
- Pobrania
- 7
- Polubienia
- 0
- Ocena
- 0
P
PrintablesGyronictonic
Printrbot Top Z Axis Stabilizer
Printrbot Stabilizer mounted at the top of the Z -axis. Not sure if it reduces Z wobble but may provide more frame rigidity. I have no issues with Z wobble but if you're playing around with acceleration, doesn't hurt to add this. Provided…
- Pobrania
- 6
- Polubienia
- 0
- Ocena
- 0
P
PrintablesGyronictonic
Printrbot LC side fan mount
A modified laser cut part #291 to mount a 40mm cooling fan. The fan can be adjusted. Will work with a Printrbot Plus Solidworks 2012 available below. Instructions Print and clean up the mounting holes. I set the holes to be 3.4mm in…
- Pobrania
- 5
- Polubienia
- 0
- Ocena
- 0
To wszystkie aktualnie dostępne wyniki.