134 modeli
juggling around with nvme 2280 sticks, i needed one box for storage. here a first attempt for 7 cards. 4 clips hold it closed, easily openable, fits cards without squeezing them. since i have only cards without heat spreaders, i designed…
Wydruk około 2,31 €–2,82 € nettoWstępna wycena jednego wariantu
Next revision of the nvme 2280 storage box
Wydruk około 0,51 €–0,62 € nettoWstępna wycena jednego wariantu
Very simple bracket to allow m.2 2280 drives to fit on the Datto ALTO 3 V2 board, which is designed to only hold 2260 m.2 drives.
Wydruk około 0,09 €–0,11 € nettoWstępna wycena jednego wariantu
A simple under table holder for my Lindy 7-Port USB 3.1 HUB. It fits perfect and dont have any play.
Wydruk około 3,17 €–3,87 € nettoWstępna wycena jednego wariantu
Please leave a like if you enjoyed the model or it helped you. :) Remixed from : https://www.thingiverse.com/thing:4715615 Started off by making it a bit easier to print by adding a slopes to some of the overhangs. Then ended up taking…
This is an adaptation of the m.2 ssd adapter by janek0809. I took their existing Fusion 360 file and edited it to fit an m.2 2230 ssd to a 2280 slot. I also filleted a bunch of sharp corners. The nice thing about this design is that it…
This model is compatible with the lego system.
M.2 adapter 2230 to 2280 simple and fast print
This model is compatible with the lego system.
This model is compatible with the lego system.
This is a work in progress and you're welcome to remix it as you wish. If you are using a FDM printer, I would suggest printing it vertically so the curve prints nicer and you don't have to use supports. I added a revised model name…
Adapter for mounting a 2230 M.2 NGFF /NVMe SSD into a 2280 slot. Converts 2230 SSD to 2280 length Not compatible with very shallow or recessed M.2 slots (mainly in newer thin laptops). Stable and accurate screw hole alignment Print…
I am using serveral M.2 SSDs to clone and backup my computers. For storage and protection I designed a simple M.2 case. This case fits a single M.2 SSD in the very common 2280 size. Printing is easy. Use your favourite material and set…
I have a 2230 M2 SSD and needed to intall it on a 2280 slot.
This model is compatible with the lego system.
Adapter for mounting a 2242 M.2 NGFF /NVMe SSD into a 2280 slot. Converts 2242 SSD to 2280 length Not compatible with very shallow or recessed M.2 slots (mainly in newer thin laptops). Stable and accurate screw hole alignment Print…
Simple holder to store up to 6 M.2 2280 NVME/SATA drives
TTI 27 Piece ½ socket set: https://www.totaltools.com.au/108878-tti-29-piece-1-2-inch-metric-deep-impact-socket-set-tt12d29iss PACKOUT™ Compact Organiser: https://www.milwaukeetool.com/storage/packout/organisers/48228435.html
Adapter to mount a M.2 2230 in a 2280 slot. I printed it in Jayo PETG with 3 walls.
This model is compatible with the lego system.
A set of M.2 form factor SSDs with both M and B key combinations. Also, S1 (1.2mm component height), S2 (1.35 component height) and S3 (1.5 component height + M and B-key versions are available. All other dimensions (including keep out…
I used this model to install an M.2 2242 SSD in Banana Pi BPI-R3.
This model is compatible with the lego system.
The goal in designing these was to achieve the maximum possible density in the smallest possible space, while retaining the ability to stack the containers so they fit into other Gridfinity systems. M.2 2280 holder 1x2 grid units Holds 6…
This is a case for a quite common USB to M.2 SSD converter. The Size of the PCB is about 27x96mm. I think its the only design here with ventilation. The case needs no screws. The fit is quite loose to be printable on my not so well…
I made my own M.2 2230 to 2280 adapter, because I couldn't find any would be exactly as I wanted. Thin but holding properly. I printed it using: Bambu lab A1 mini PETG filament 100% infill normal support type Supports are important…
Design Log: I changed the thickness of the piece. Did a thicker base for vertical printing. Minor adjustments for better aesthetic. I printed with PETG (Grey Overture) in a vertical position with supports.
Every time I am moving or disassembling my Ikea Elvarli shelf, a few of these gets broken in the process. This time, I finally realized that it is simple enough to be 3D printed new part. Traced some pictures and created an STL file. The…
Extend an 30mm NVMe to 80mm. Work with a 0.7mm thick PCB. Category: Computer
Whoops, I bought a 42mm length SATA Expansion Card but my motherboard only has screws at the 60mm and 80mm mark. This part holds my card in place with attachments at both the 60mm and 80mm points.
These Chuck Cradles support the chuck on the lathe bed (ways) for the Precision Matthews PM-1228 metal lathe during chuck installation and removal. They are sized for the 6" (160mm) 3 jaw (standard) and 8" (200mm) 4 jaw (optional) chucks.…
I used generic PLA with 20% infill and ironing for a better finish, as well as supports. I hope you find it useful.
This caddy should fit at least for the following Huawei Systems: RH2288H V3 RH2288 V3 RH5885H V3 RH5288 V3 To my knowledge there is currently only one type of LFF caddys huawei produces, so the should also work on other systems. For…
it's a tight fit but it should work. flexible adator for 2230 or 2260 cards. you should print it in ABS or in PETG under the cpu could get warm.
This extends a standard NMVe 2280 slot to fit a 22110 SSD. It screw mounts to the 2260 and 2280 standoffs and can be pre-flexed to clear components as necessary. Print Settings Printer Brand: Monoprice Printer: Maker Select Rafts: No…
Thanks @choovick for the original version of the model. This one has been modified to accommodate standard size SSDs.
Universal M.2 SSD Adapter (Multi-Format Caddy) This model is a comprehensive hardware compatibility solution designed to extend the life of your storage components. It is a rigid "Caddy" or frame that allows you to install…
I needed a slim adapter for a 2242 to 2280 M.2 SSD. I also added a STEP file for easy modification
3D Printed temple tips on my old rb4228m scuderia ferrari collection When my temple tips started to brake i decided design and 3D print new tips and it worked well. Need to be printed with a felxible filament. You need a heat gun or a…
This model is compatible with the lego system.
Stackable Tray for m.2 SSDs. Remix of my DIMM/SODIMM Tray
I didn't want to spend another 17euro on these little spacers that you need to install the dishwasher. These are the plastic components of the Bosch mounting kit (part number 00622861 / 622861). These parts are used to mount a dishwasher…
Raspberry Pi 5 and 2280 NVME SSD Cooler Case The case has been designed to house an NVME drive mounted under the Pi. The available drive I had was a 2280m, being 80mm, which is longer than the case length, so it protrudes a bit. (I intend…
T-track Stock. 9 inch (228 mm) length Perfect for woodworking jigs, sleds, assembly tables, CNC, downdraft or other work table tops. Fits in a .75" x .375" dado (19.1x9.5mm). Use #6 tapered head screws for instillation. Hole spacings are:…
As I sometimes have to attach NVME's via USB C to my computer and want to be able to chage them quickly i created this little bench You will need: 1x the USB-C to NVME adapter Buy here: https://s.click.aliexpress.com/e/_c39JjrDd…
The ICY-Box IB-2280SSK is pretty cool to have 8x SFF Drives in a Desktop/Server. The cooling fan however, is pretty noisy. To ensure clearance, I created a 70mm (Icybox) to 80mm fan adapter with an extension, which ensures enough…
This case is intended to print without any support. It's a total of four parts - Top, Bottom, 2280m.2 brace and (optional) screen mount. It's accommodates 2280 length m.2 drives. It has mounting place for a 4010 fan above the Pi's SOC.…
I couldn't find a wall mount for the Lego McLaren 42228 set other than a 3D print from the UK for $12 with shipping. ended up making it myself. It holds the McLaren to the wall and secures it with a pin. I had to use a M4x50mm countersunk…
Print this with the holes on the build plate, using normal style supports and 25-50% gyroid infill. The supports should snap right off with minimal cleanup required. This is the same part I designed and was selling. JD M122280 585195…
Print at 0.2mm or 0.1mm layer height for accurate dimensions. Supports recommended on screw end only, SSD end does not need supports. Allows use of 2230 SSD in computers or other devices designed for 2280 SSDs with no mounting options for…
Lenco S002285 Replacement Hinge for models: Lenco L-3809 Lenco L-3818 Lenco L-401 Part1 is comleted and tested. Part 2 is not completed!
This 1970s coffee grinder unfortunately had a damaged lid. Our model faithfully reproduces the same dimensions, allowing you to restore this vintage piece accurately.
This is a stand extension for BenQ GW2280 monitor. My table is low and I wanted the top of the screens just below eye level. IMPORTANT: Exclude supports from the middle of the pocket. Support placement is shown in an image above ^. I…
Fits the PM-1228 lathe backsplash, 5 recess's fit 6x3mm magnets
These are replacement drawer dividers for Akro Mill parts cabinets. The dividers also have the ridge on the edges to fit into the side slots and keep the drawers from expanding sideways. Pictures show original and 3D printed version.…
2242 to 2280 dualsided nand ssd
Super compact container box for hard disk 2280 M.2 NVME 34 pieces. Perfectly fitted for 2280 SSD, a very simple print. Very tight tolerance of 0.1 mm. The lid should be a press fit with a properly calibrated printer. If you cannot…
Modelos compatibles con set legos
🔧 About the Model 🖨 Designed specifically for the Core One printer — no extra tuning needed 🧱 Studs are slightly oversized for a better grip 🛠 SolidWorks source file included for easy customization 💡 Tip: When printing with a 0.4 mm…
Converts 30mm length M.2 SSDs to a more standard 80mm.
Door for cabin filter for diy install filter. More info here
VEX IQ 3x3 Plate (228-2500-031)
Stacks with the original DIMM Storage Tray by mars9601. I modified the original solidworks model to create these, leave a comment if you'd like me to upload the .SLDPRT. Both a 2280 only and a 2280/22110 combo are included. The models…
This is a LEGO compatible file that works as an adapter to allow for the VEX 200mm Travel Omni-Directional Wheel to work with LEGO Technic Axles. There is a 4mm version and a 3mm version. The 4mm version will fit perfectly, and the 3mm…
this is a replacement part for the Festool Saw blade holder closure mine broke of so printen a new one
Bought a cheap SSD to USB-C adapter off e-bay, and needed a cover for it, for mounting besides my raspberry pi. Very tight fit, which is what I went for. Removal might be destructive for the cover. Print slightly oversized if you want to…
A printable 3d model for SSD M2 Rack
Reimplementation of the original model but with more width to acommodate NVMEs with integrated Heatsinks.
May be, this model not final iteration
40 slot m2 2280 drive storage. I printed this with a 15% infill and it was super solid and sturdy. Opted for no lid or latches.
Hi everyone! Here is my universal M.2 NVMe SSD adapter set, covering all standard form factors. It allows you to fit smaller drives into larger slots—from 2230 to 2242, all the way up to 2280, and every combination in between. The model…
JEYI Thermal Conductive Silicone Pads: https://s.click.aliexpress.com/e/_omRiFoe Recommended JEYI M.2 2280 SSD Heatsinks: https://s.click.aliexpress.com/e/_oER99GA https://s.click.aliexpress.com/e/_opsow18 There is multiple versions of…
This is a blank for an M.2 2280 slot / card that you can use to make any design you like. No support material needed. I would suggest printing it at 0.2mm layer height, as the thickness of the blank is 0.8mm. There's two files included:…
M.2SSD_2242-to-2280.stl_1
It a Singapore base Residential Apartment building located in Tengah region
This lets you use a 2280 size nvme drive with the Raspberry Pi m.2 Hat+, which ordinarily does not support this size. Just use two of the screw mounts for the hat to also connect this adapter. I designed this because I didn’t read the…
This latch broke on my vaccum and I didn't want to order a whole new neck for it (~$50) so I designed a replacement.
My daughter got a LEGO 3‑in‑1 set for Christmas. After building the first model, she wanted to try another one — but she absolutely refused to take apart the dog she had already built. I thought: no problem, I’ll just print a few extra…
A copy of this part. It should fit.
Bracket to allow installation of M.2 2280 SSD in the M.2 2260 slot on SuperMicro X11SSH-TF/CTF motherboard. Requires two M3 heat-set inserts. Install bracket on motherboard in the 2260 retiontion screw hole. Other end provides proper…
Replacement parts for Frog Engineering P226 228 229 Tokyo Marui system conversion,all brands. TM version - WE, DE, TM, KJW version - KJW only Details can be found here: https://youtu.be/gbfvtSGgRUw
Transponder worn on the Starfleet Field Jacket in 2285 Wrath of Khan Era
Vorsicht: Spielende Zahlen ist eine Sammlung von Lernmaterial für Unterricht und Selbststudium. Nach und nach wir zu den meisten Drucken auch noch ein fOrscherblAtt beigefügt, das den individuellen Lernweg begleiten soll.
Two lids for use with the original modular case system to allow Rak2287 and Rak2245 Pi hats/concentrators exposing the heatsink for cooling (and hotrod looks) as well as adding a boss with hex for an external SMA connector. Useful for…
ORGANIZZATORE GT228 Realizzato: www.webtessitore.it IMPOSTAZIONE DI STAMPA Stampante: Artillery Sidewinder X2 / X3 PLUS
Mounting for alu profile for a Lindy 7 Port USB Hub. Part Number 43228 Printing in 0,20mm PLA 10% Infill
This is repair part for my mechanical juicer Philips hr2285.
Remixed a design so it fit on the back splash of the PM1228 lath. Added two holes to pass through 1/4 20 threaded rods to combine and strengthen them. Also created more holders like Oil Can (with brush in lid), oil bottle that came with…
This is a 32 tooth, 20°PA, .91 module gear designed to replace the threading dial gear on PM1228 lathes. It has a 10mm bore and 4mm keyway. Category: 3D Printing
Needed some dividers for my akro-mils bins so I whipped some up quick in fusion, and thought I'd share in case I can save the time for someone else. Added a flared base both for bed adhesion, and to make it easier to grab small parts.
Deckel für die Moulinex 228 "Super Junior" Kaffeemühle Die Deckel Konstruktion weicht vom Original ab, sodass beim Druck keine Stützstrukturen benötigt werden (abgeschrägte Außenkante)! Ich habe auch den Rand innen zur besseren Reinigung…
Trav-A-Dial bracket for PM1228LB-VF lathe, Solidworks file available on request. Two machine nuts are inserted in the grooves, one for tightening the dovetail (I used a thumb screw) and one for pushing the Trav-A-Dial forward to engage…
I have a few 2230 SSDs left that I want to install in motherboards. However, some of the motherboards are missing the standoffs for the drives. So, I designed this remix. Use an M2.5 countersunk screw to fasten it. A small support element…
A simple mount for the KA2284 Power Meter board. The board snaps into place in the mount. In one of my robot builds, I use the KA2284 for modulating the brightness of LEDs based on MP3 audio, so I have the LEDs on the board wired in a…
A basic model to cover the conduit cutout if the original cover is lost
A compact protective case for one M.2 2280 SSD. Only 11.1 mm thin, it fits any 2280 SSD without heatsink , NVMe or SATA, single or double-sided, and keeps the tiny M.2 screw with the drive. A taller version with a spine label is included.…
This part broke on my IKEA aneboda, so maybe this model helps someone. I would recommend printing upright, so the pegs don't break along layer lines. This model is an unofficial replacement part compatible with the IKEA 102284 Tube…
I needed an adapter to install a Hailo 8 AI Edge processor onto a Raspberry PI5 M.2 hat. I didn't like any of the existing solutions I found, so I made my own. It will probably have some pros and cons to others that are already available.…
Designed in fusion 360. Handle is 9 inches or 228.6 mm long total. Add text if you want to customize. Please like and upload your makes
