NEJE A40640 (40W) air assist
Air assist for NEJE A40640 (40W) laser module.
Wydruk około 0,61 €–0,74 € nettoWstępna wycena jednego wariantu
- Pobrania
- 227
- Polubienia
- 16
- Ocena
- 5
154 modeli
Air assist for NEJE A40640 (40W) laser module.
Wydruk około 0,61 €–0,74 € nettoWstępna wycena jednego wariantu
Die 440/480Watt Solarkoffer von Plug-In Festival, Wattstunde, Enjoy Solar oder Offgridtec können nur in einem festgelegten Winkel aufgestellt werden und der ist extrem flach. Meine einfache Lösung verwendet mehrere Schlüsselbänder mit…
Pete, very kindly skulpted these pulse rifle files to go with my full size T800 build and during our discussions I mistakenly gave him the wrong measurements. Old saying measure twice cut once. Well did I do that, No : ) I was so excited.…
Update - revised design available! I added an updated design because recently I noticed that during the automatic height measurement the M3 screws slightly touched the upper housing when the laser head was moving to the reference point at…
Mounting bracket for Creality Falcon 2 40W. Allows you to add a red light laser to the Falcon 2 2 40W to allow easier alignment. No addition screws or tape required to fit. It should be a nice secure push fit to the top of the laser…
Mit den Griffen lässt sich das Lasermodul sehr einfach bewegen. Der hohe Griff verhindert, dass der Laser an der Gehäusekante bzw. der Lichtleiste vorne anschlägt. Weiter kann er durch die Kerbe nicht hin und her rutschen. Die 20W und 40W…
It's a bit hard to get a good grip on the xTool S1 modules to move them around. I made this for my 40W (I don't know if it will fit other modules or not). It's a little tight when attaching, but doesn't move at all once it is in place. I…
Revised version of my simple foot mount which supports alignment of the 500x500 honeycomb bed and keeps everything in the same place. Need to print 2 of each. Filenames explain which ones are for which feet My feet are positioned at their…
Thanks Peter H for making the original customizable via OneShape! M4 screw will fit on the open piece to allow removal of the power brick. If you don't want the open end, then print 2x closed ends.
…Please be sure to hit like & post a make, I'd love to see your prints! Mount the Sovol 40W laser to your SV06 & SV06 PLUS printers. You'll need: 4x 6mm M3 cap head bolts 2x 8-10mm M3 cap head bolts Print laying flat on its largest face…
This is a printed air-assist nozzle for the NEJE 30W and 40W "new style" laser modules with the amber/red window. Simply replace the window with the nozzle part and insure the lens assembly is properly fitted into the cone. Attach a 6mm…
Laser beam alignment tool for the Chinese K40 40W CO2 Laser. The tool has two parts, one for mounting on the mirror and one for mounting on the laser head. Using tape or paper to mark positions has the problem of smoke residues getting on…
For MacBook Pro 14 inches 2023, 96W USB‐C - MagSafe power adapter Added versions : 61w - 67w - 70w - 140w
Bester Abluftkrümmer für deinen S1 - Seitlicher Ausgang - AD=100mm. Update: Auf Wunsch hinzugefügt, Datei für den original xTool Schlauch, welcher aufgeschoben wird: "Seitlicher Ausgang_originalSchlauch_AD74mm.obj" Konstruiert in FreeCAD…
Falcon2 Pro Collection This is a holder for a 5V 5mW laser crosshair pointer for the Creality 22w/40w/60w laser module used to line up material on the bed for cutting accurately and set back far enough so as to not collide with the front…
case for HBV 5640 eg Voron 2.4 ---- BOM: 4x M3x10 or M3x12 2x M3x5x4 insert 3x M2x4 tapping screw to mount the cam ----
Honestly, this design isn't super great.
Print one of each of the fronts and two of the backs.
Mounting bracket for Creality Falcon 2 40W. Allows you to add a red light laser to the Falcon 2 2 40W to allow easier alignment. No addition screws or tape required to fit. It should be a nice secure push fit to the top of the laser…
Sized specifically for the Apple MAC M1 charger with a capacity of 140W. It is a pretty tight fit if your tolerances are good - so size up a bit if you want it looser. The charge port is accessible while the charger is inserted, so…
Delta PMZ-24v240WDAL PSU for the Prusa i3 MK3s+ (The black version) You can use this STEP model as a base start for any modification/upgrade.
(References like [##] refer to specific labeled images above.) Note: Ensure that the cord clips line up correctly. If you print the files tagged "4b," you'll end up with clip positions shown in the photos. The files tagged "4c" will have…
I made 4 versions for different focal length settings.You should use some rubber ring for sealing from the laser side (red circle on picture) Air input diameter is 5.4mm My air source - 2x CT-404 silent aquarium air pump…
The upgraded model also makes sure that the origin of the machine is in the corner of the honeycomb.
This is a mechanical X and Y End Stop upgrade for the K40 40W CO2 laser. The original K40 is equipped with one mechanical end stop for the X axis and one optical end stop for the Y axis; with origin at the upper left corner. This end stop…
Designed to hold the standard 12mm cylindrical laser crosshair module you find on sites such as Amazon or eBay. Requires that you replace the stock 5mm M3 Countersunk Socket Cap Screw with an 8mm or 10mm one. The laser is a tight friction…
A mount for the Laser Tree LT40W-AA diode laser to secure it to a Biqu Hermit Crab tool-changer. Two Models are included: A simple mount A Voronoi sketch version to match my personal Ender 3VO Theme The Lt40aa model was sourced from…
More Gridfinity stuff! I needed a place to properly store my 140W Power Adapter, so I made this bin. Since the smaller size it would fit is a 3x3 bin, I left a slot to also put the cable beside it.
This is a mount for a 12mm cross pattern laser to mount to the Creality Falcon 2 40 Watt laser module. It uses the USB C port on the laser head to power the laser module. The bracket mounts to the front two screws holes of the laser head.…
This is a mount for the Creality Falcon 2 40W Laser Cutter to add a Laser Crosshair. I just wanted something sturdy and didn't move when I touched it and thought I might share :) First ever upload, hope it works well for you guys (and…
Mount your dell power supply to your opengrid wall!
Falcon2 Pro Collection This is a set of half fan intake shrouds to help the laser unit not pick up particles from the surface being worked on to minimize build up in the cooling unit. Creality does provide instructions on how to pull the…
Parametric Toolrest for Parkside Grinding Machine (240W) STLs for two angles have been provided, but since the model is parametric, STLs for any angle can be generated 0 degrees (horizontal) 10 degrees (for grinding the lathe tool bits)…
Anker 40W 5-Port USB Wall Charger PowerPort 5 Under Table Mount
I really like the handle on the Jury-Rigged Boomstick remix Shirley Productions did on their original Libra, but preferred the barrels on the original, so I mashed those two frames together and it's a banger. Barrels were also too large…
This Mostly-printed Z-axis for Neje 30W/40W laser modules is a mashup/modification and remix of a couple of designs: Silvester's 3D-Printed CNC Z-axis for Nema17 (Pinshape) and leadscrew/nut from 3DPRINTINGWORLD's Linear Ball-Bearing…
Holder for your 140W MacBook Charger. Based off Zach Freedman's gridfinity system .
a simple way to manage the new MagSafe cable
Additional parts: 4x M3 heat insert, 4.2mm outer diameter 4x M3 bolt, length anywhere between 10mm and 30mm. Assembly: Install the heat inserts in the front part's back side cavities. Slide the device into the front part, from the back.…
easy to print / one piece Air assist nozzle for most K40-Lasers. It's the updated version with a normal 12V blower. So there is no hose in the air. break away supports included ;-) Print Settings Printer: Upgraded Geeetech i3 c Rafts:…
Couldn't find one which fit the 240EB so here's a quick and dirty one. Friction fits close enough to stay in place and only contacts the printed part in small areas too keep cooling from being impaired. Use something other than PLA since…
Remixed this well designed cord organizer. Thanks to @curby_289762 for the great design and making the fusion files available for remix work. added a hook to hold the outer wrap pushed in inside surface .25mm to tighten on charger block…
Designed this to keep my old Stanley glue gun organized, has a nice little storage area for 25 glue sticks and a spot to stash my little glue gun stand. It is stackable and will work with a gridfinty standard 5x5 lid Built for abuse, so…
While designing the Gridfinity storage bin to store the power adapter, I also made this model to make sure it would fit as expected.
Case for DC 6-30V 140W Multi Protocol Desktop Intelligent Fast Charging Module
This is a remix with metric bolts, M3/M4. In my remix the disc is 20mm and and a bit thinner. STL model for both M3 and M4 screws (I use M3x30 screws). >> If you like it, please leave a like, rating or a tip... :) Print Settings 0.20mm…
Remixed from this: https://www.thingiverse.com/thing:4200890
Creality Falcon 2 40W Laser Crosshair Bracket Should fit all the Falcon models. Used this as inspiration:…
It helps to minimize cable damage and extend its lifespan. The protector is designed for 3D printing with a layer height of 0.16mm and three walls, providing solid coverage. It uses 52 grams of filament and can be completed in…
Based on this module: 4s/100W module (Aliexpress) Need two long screws 3x40mm. Can be printed without supports. Supports almost all “fast charge” protocols: PPS/AFC/FCP/QC3 +/QC3.0/QC2.0/SCP/VOOC/PD3.0/PD2.0. Optional flashlight LED can…
Be carefful, please desolder capasitor from powerbank module and solder to wire to save space. I used: AMASS XT60E-F 1 Cover Y Metal 5.5X2.5mm DC099 Brass Hot Melt Insert - Length 4mm 50pcs, M3(OD4.2mm) KCD1 Power Switches - Black 2Pin,…
A quick and dirty remix of the holder arm to accept 28mm soldering irons like the Weller 40W (WLC100) . I had success when printing with 2 walls and 20% adaptive cubic infill in OrcaSlicer with Overture PLA.
Designed to be used with the standard mounting plate (not the angled one). To install the housing, simply loosen the screws on the doorbell’s mounting plate and slide the housing into position behind it. A small clearance at the top of…
Stand to hold a 140W Macbook charger vertical to reduce its footprint.
Since my K40 laser came with a broken laser tube, I had to get a replacement. The new tube (real 40W tube) is 700mm instead of the original 630mm tube. I therefore had to enlargen the case. Since the power side is opposite of the laser…
For fixing M2 module For fixing M2-M3 panels
With how low the guard comes down, it can easily hit any clamps/hold down methods. So I decided to model up a new plate without the guard, since I run the machine in the enclosure, always wear goggles, and keep the door closed so the…
Connect 38mm vacuum hose to get fresh air for laser cooling fan. I have mounted mine with 2 of the laser top cover screws. I have the vacuum hose coming though a hole that I drilled to the tabletop. Printed with supports using PETG for…
Ultimate 140W FPV Power Bank Case (PD 3.1 28V 5A / 2-6S LiPo) This is a rugged, active-cooled housing for the 140W Bidirectional PD 3.1 USB-C Module With XT60PW-M connector . It turns your 2S–6S FPV flight packs into a high-performance…
This is an air assist nozzle for the popular 40w Chinese (aka 'K40') laser. It directs compressed air at the 55mm focal length of the included lens. It has female threads for the hose that comes with the Harbor Freight Airbrush Kit (…
More Gridfinity stuff! I moved where I used to store my power adapter from a shallow drawer to a deeper one, so storing in vertical manner is possible (different from my original design) . There are other models to store it vertically,…
Here my version of AirAssist for Neje A40640 Laser Module (alse suitable for A40630). I mounted two rubber ring (1x 10x2 + 1x 6x2) for sealing the laser, but one may be enought I used a 6mm (ext) - 4mm (int) air hose, and the input side…
Gridfinity for Apple 140W Charger and cable
I recently acquire a cheap chinese 40W CO2 laser engraver/cutter. It's great value for its price but not user friendly. The machine do come with red dot laser side mount next to laser head. It's simple but never line up correctly to the…
Power supply frame / housing that offers the option of winding up the long 230V cable and the USB-C cable.
Soporte de mesa para auriculares Jabra HSC040Wa Jabra HSC040Wa Tischständer für Headset
djk4linux's air-assist nozzle for the Neje 40W lasers is a bit long for cutting thick materials. So I remixed it for some shorter options. https://www.thingiverse.com/thing:5073015 The original nozzle extends 15mm from the base of the…
This is a panel mount interface for a USB-C PD battery charge/discharge module. 140W 2-6S Lithium Battery Charging Board Bidirectional Fast Charging Module With Automatic Temperature Control Function IP2366
This is a spare leg for combined fridge+freezer Beko RCNA406I40WN Probably will fit to another model from Beko, but I have no way of testing it. Old one broke and was lost so I copied crucial dimensions from one that was left.…
[DE] Leistungsstarker DIY-Zylinder-Lautsprecher mit TWS & 140W PD Dies ist ein robuster, zylindrischer 2-Wege-Lautsprecher, der auf erstklassigen Sound und mobile Power ausgelegt ist. Das Gehäuse ist für einen 16,5 cm (6,5 Zoll) RECOIL…
Plunk your 40W laser into your 69mm router holder. No need to remove brackets requiring retramming each time. I used PLA, and haven't tested it while running the laser so heat issues might be a problem. Print two obviously. I used about…
This model is a remix and just contains stl file.
inmovilizadores para dejar fijo tanto la grabadora laser como la base para evitar tener que estar alineando a cada rato. se fijan con tornillos a la base de madera o a la mesa (recomendable una tabla para no romper la mesa). se tendrá que…
The HP LaserJet MFP M140w always feeds the paper at an angle and the printouts become unusable. That's why I designed a paper guide. Simply attach the two brackets. The paper is no longer fed at an angle. The paper guide is needed twice.…
This is a simple Z height adjuster for my Neje 40Watt laser. The support itself is secured to the laser module by origina screws. It is necessary to add a M6 bolt and a M6 nut. There is also a spacer to avoid to scratch the original…
X-Axis Assembly The bottom 2 wheels should be assemble before putting on the laser, otherwise you gonna have a bad time. LT-40W-AA Model: https://grabcad.com/library/laser-tree-40w-air-assist-laser-head-1 Y-Axis Assembly Before attaching…
This is a 3018 CNC mount for the Laser Tree Laser Module (LT-40W-AA) and maybe others? There is a block on the side for the air assist hose to be secured with a cable tie. Category: DIY
The cover is necessary to protect the power supply when it is mounted in the central control cabinet
I wanted to mount the Ikea Askstorm 40w usb charger to the side of my nightstand to clear some space. We also travel with the charger, so it had to be mounted in a way it could be removed. With this simple print it's easy to attach the…
organizer for singel or multiple laptop chargers modular. printed on a bambou X1 carbon .4 nozzle .2 layer high with PLA can insert 8X3MM neodymium magnets (not necessary)
Amazon product ID was B08F9X1Q4J with the godawful title of “Delippo 240W 20V 12A Laptop Ac Adapter for ASUS ADP-240EB B Rog Zephyrus Duo 15 GX550LXS RTX2080 rog GX550LWS-HC099T i7-10875H rtx2070” It's almost certainly a re-badge of…
A Neje 40W (A40640) module Air assist. (for 30W module see https://www.thingiverse.com/thing:4843808 ) It comes in two version. 6ID which has inner diameter of 6mm. 6.5ID which has inner diameter of 6.5mm. Height of the laser head should…
A chunky grip and vertical + horizontal arca-type tripod plate for the Zhiyun M40w pocket floodlight. It includes a hole for the USB port to keep charging, and plenty of room to adjust the dials without removing the grip. Pictured here in…
Fume extractor adapter for the popular 40w laser engraver. It uses the screws already on my machine, that were keeping the inner fume collector. Diameter 100mm (about 4 inch) Hope it helps. Category: Tools
No screws needed 2 part case Print 99.9% infill, 0.2mm layer size any material
A mounting holder to attach a Dell 240W adapter neatly to a desk.
Cloudray's K Series laserhead's 3d printed mount for K40W laser cutter. 2 x (25mm x 3mm) bolts are needed. i have also included a 3rd drill hole for mounting my laser pointer which is still W.I.P. About 40min print time with…
Hast du auch Probleme mit der integrierten Kamera? Dann ist das jetzt die Lösung! Mit meiner Halterung für einen 12mm Kreuzlinienlaser kannst du das Werkstück problemlos ausrichten und dabei ist es egal, ob es flach aufliegt oder in einem…
When I got my K40 40W Chinese laser, the ZnSe lens had no support - it was just dumped in and screwed in place. As there was no support or protection the lens could easy get scratched, break or get out of focus. This thing gives the…
Es geht um ein Gehäuse für folgendes Netzteil: https://amzn.to/3Q7t0pd Ich habe mich beim Amazon Partnernet registriert, verdiene daher als Amazon-Partner an qualifizierten Verkäufen und bedanke mich daher, wenn ihr die Links nutzt. Ich…
This power bank is very easy to assemble and not so expensive). I ordered the power bank board and the BMS board on ALI. They cost me 11.3 dollars. The batteries are used from a scooter with a final capacity of 2500 mAh. You can use only…
Быстрая отрисовка платы для быстрого прототипирования устройств.
Made a case for the Aftertop 140w charger . Designed to be secured on the coffee table leg with cable ties. But I included step file so you can easily modify it for your specific needs.
A new plate, to mout the new NEJE 30w and 40w laser modul to the Ortur Laser Master 2 7w, 15w and 20w frame. Print Settings Rafts: No Supports: No Resolution: 0,4 Category: 3D Printing
This is a cord wrap for a 40W Macbook charger. Category: Computer
Remix of Andreas Kanner's excellent Badger 2040w enclosure design. Thanks for sharing the .STEP files! printed in PLA For ‘battery mount’: organic supports, flat side to print bed other components used: 1x Pimoroni Badger 2040w 4x M2 x 8…
Finally managed to get a quick swap kit, and while the plate for the original toolheads and 10W toolhead lines up the original mount holes, keeping the focus length the same, not so for the other lasers. The 40W and 2W IR both slot down…
travel box for the 140W apple charger (model A2452, 96x75mm)
passend für: https://www.amazon.de/gp/product/B00VUGOSWY/ref=ppx\_yo\_dt\_b\_asin\_title\_o07\_s00?ie=UTF8&psc=1 Category: Other
Got the Sovol 40w laser head for use with the Xchange and wanted to mount it. With a static BL Touch mount (that stays on the printer with the electrics). Please see my other makes. Mounting the laser straight to the tool changer it sat…