Drink holder camping chair Quechua Decathlon fully 3D printable
Print all 3 files with 100% infill and in a material that is suitable for outdoor use. E.g. PETG.
- Pobrania
- 358
- Polubienia
- 129
- Ocena
- 0
Liczymy pasujące modele…
Print all 3 files with 100% infill and in a material that is suitable for outdoor use. E.g. PETG.
Replacement male side-release buckle for Quechua/Decathlon backpacks with a 40mm belt. This specific buckle was found on a “Quechua Bionassay 22” backpack, but will likely fit several other backpacks using the same design. The code on the…
VIOO CLIP Decathlon Light Holder for rods - bike handlebar, seat rod... Instructions : Outer part needs to be printed using flexible filament (TPU…) (experiment with the toughness) Inner part needs to be printed using using rigid filament…
The Forclaz Headlight from Decathlon is super bright and has a rechargeable battery. For emergency, it can also be operated with non-rechargeable batteries. The holder is designed to be easily fitted with zip-ties to the handlebar or the…
Lid for Decathlon Led Light QUECHUA Printed with supports
update 05/20/2026: Rev 1 is the original file Rev2 I made the band 1mm taller in the z direction to add a little more material around the head and threads of the screw Rev 2.1 has a 5% smaller inner diameter requested by bob92553 About a…
The Silvana adapter for Decathlon face masks can be used for CPAP assistance to help fight the COVID-19 disease. The functional design is inspired on Charlotte valve from Italy, redesigned from scratch with the philosophy of making it…
lost two feet of my chair in a trip, was already sinking into wet ground a bit before, found the original file and made the inner diameter smaller then removed the holes 2024/10/8 update: revisiting the file because I need to print a set…
Here's my adaptation of Peter H's ball feet to the cheap copy Decathlon made of the Helinox chairs. The original robber feet sink in everything, but I still wanted to keep them on my chair. So, I made use of the hexagonal shape of the…
This adapter enables the use of a car/bicycle pump to pump up an Air Seconds tent to the 7psi/0.5atm that is required. Can also be used for mattresses and other inflatable camping equipment. Be aware that a car/bicycle pump can easily pop…
A unicorn horn that attaches to the center-front hole of Decathlon's Oxelo B-100 helmet. I believe this one is the smaller size (47-52cm), but I might be wrong, and it could also work for both! I have included step files so that you can…
a mount for speedometer and light between my aerobars. mount with zipties OD Aerobar 22,3mm Distanze between Aerobars (middle): 127,7mm Printing: 0.2mm Layerhigh ASA 4 Walls 15 % Gyroid
A small part to attach your brake cable from front to back along the bike body.
Custom 3D printed spacers designed specifically for Decathlon VAN RYSEL Long Distance triathlon handlebar extensions. These spacers allow precise adjustment of aero bar positioning for improved comfort during long-distance cycling,…
Zoom throw lever for the Athlon Midas Tac
Print the model with 0.2 mm layerheight and set all infill to cocentric. best to print with 100% infill and in PETG
A throw lever designed for the Athlon Ares BTR Gen 1 scope. It should also fit the Ares ETR Gen 1 and the Midas Tac, although I have not tested that. Hardware required: 1 M3x10 screw 1 M3 nut Category: Sport & Outdoors
For this print you'll have to get: x4 hex nuts M4 into the print while this one will be in break around 22min x4 screws M4x12
EN I bought this tent Decathlon MH 100 (2People) a few years ago. When setting up, the two brackets always unfolded for me. So I always held them together with Velcro, which you use as a substitute for cable ties. But I didn't find this…
Training butt hook on biathlon rifle
Its for the bottle that is shown on the picture, and it using original oring seal.
A stealthy way to hide an Air Tag under your bike seat ( modeled to fit the 27.5" Mountain bike Rockrider ST 120 Disc Seat: https://www.decathlon.co.uk/p/27-5-inch-mountain-bike-rockrider-st-120-disc/_/R-p-305496 ). The two pieces clamp…
This is a custom-designed mount to securely attach your Deeper Sonar (Pro+ or CHIRP+) to the FLTB-5 float tube. Fishing with a Deeper on a float tube can be tricky without a dedicated arm. This mount is designed to be compact, sturdy, and…
This is a cockpit with a Garmin Nav screen for the Hanger nine Super Decathlon. This is for the Giant scale 40% model but can be re-scaled to fit any model. If you prefer the version with a radio stack instead of the Garmin, the files…
This adapter can be used to connect a 3M filter to Decathlon Subea Easybreath snorkelling mask. Print instructions The print can be coated with XTC-3D which will make it 12-times more pressure tight. You will have to buy the 3M 6895…
Cale d'une hauteur de 20mm. Vous pouvez régler la hauteur sur votre Slicer. Fabriqué en ASA. Le fabricant est seul responsable du choix du filament, du choix du remplissage, de la solidité de la pièce, et de sa fixation.
The adapter has been designed to allow the use of filters on the Decathlon Easybreath mask, with the intention of creating a piece that is an excellent compromise for printing with less material, less printing time and best results. The…
This applies to popular and cheap Decathlon scooter. Original part got broken and no replacement parts are available by Decathlon. This mudguard serves as brake so without it the scooter is quite dangerous for a kid - thus unusable.…
A connector to use the Decathlon Pump to pump a Kite up. Used by myself on a Slingshot kite Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: 0.10 Infill: 100 Filament: Generic petg Black Notes: Best…
UPDATE: Checkout Kroll Fu's remix if you desire smoother look. 3D scanned the mouse and made this shelf. Fits into standart hollow inserts for Honeycomb storage wall. The fit is kinda loose, so other similar mice might fit. Best to print…
I used a gum tape between the mount and the helmet to make it more stable and not ruin the helmet. For the nut I used an auto-lock type M5, but I guess that a normal M5 nut will work as well. To mount that on the helmet I used 2 simple 4…
A lightweight alternative mount for your rear bike light. Four small zip ties required (no metal screws make the mount lighter and more reliable). The mount is compatible with Decathlon/Elops lamps (wit clip 74852): Elops RL 510 Elops CL…
A number plate for triathlon that attaches to Specialized Shiv bike frame. Category: Sport & Outdoors
GoPro mount for Decathlon Forclaz HL900 (suits other forclaz headlights too) headlight. Best fit together with Rockrider GoPro mount on helmet ;) https://www.thingiverse.com/thing:5443026 Due to mechanical properties, print it separated…
Like Charlotte valve this design allow to connect Decathlon mask to respirators and alternatively two 22mm filters. Designed with the intention of creating a piece that is an excellent compromise for printing with less material, less…
Added step file, and example model I made for a cheap Aliexpress lamp. Let me know if you liked it. The lamp holder should be printed on it's side with only supports for the horizontal surfaces.
Hello, a quick remix for my Decathlon RC500 (flat stem). Print in PETG, 0.2 is fine, but you can try 0.16.
Version with improved airflow of Breami Valve Like Charlotte valve this design allow to connect Decathlon mask to respirators and alternatively two 22mm filters. Designed with the intention of creating a piece that is an excellent…
Mount to attach your race number to your bike for triathlon or bike racing. Tucks neatly behind the seatpost, a lot cleaner looking than wrapping around with double stick tape. Guaranteed to save you 3 seconds per mile on the bike leg...…
I bought these mirrored Decathlon goggles and they were alright. The L1 nose bridge was closest fit for me but still felt a little wide. So, I made a simplified functional model of the L1 nose bridge in Fusion 360 and scaled down the…
Relacement part for the Decathlon Evadict Ontrail 900 Headlamp. 3D model of the rear part acting as a battery holder.
Backpack organizer for Mini Quechua (Decathlon) -Keep thing organized -Backpack stay always vertical -Protect from drop (Walls 3mm, infill 20%)
Llavero Triathlon Ironman No MMU
Update added improved variant I kept the original design, but improved the rigidity and elegance of the shapes. The back is ergonomically shaped to copy the forehead. I paid particular attention to modeling the stops around the joint. I…
A little jig to help dry out the bladder. Length wise, its' a bit short, but this fits my 300 Voron. you can extra insert the closing slide to keep the bag open. The width might be a snug fit, but you can press down on it and it will flex…
Reduction for Decathlon Subea Easybreath 500 (wider snorkel) for filters using thread Rd 40x1/7" (NATO thread for gas mask filters). Use some some rubber gasket (40mm) or filter seal. Break out inner circle (its only for support).…
Parts are for the Large version of the Velobuild TT-023 frame only. Front compartment has just enough room for a spare TPU tube. Main compartment has a pull-out tool holder that fits my pump, multi-tool, allen keys, tire levers, and a…
2025/05/07 UPDATE - I added two new variants, seeking a snug and tight fit. I created this model to hold my bike pump for my cycling sessions. It should fit any bike with the bottle holder screw mounts. The holder is compatible with bike…
Rack for the dumbbell set from decathlon. The model has two parts. the lower part is 1.5mm thick and can be printed in TPU with a simple filament change. Only works with filaments that sick to each other. PLA und TPU should be fine. You…
(EN) Backrest for the R500e cargo bike. This makes the little one sit much more comfortably. Can also be used to secure loads, as the bar can be freely adjusted and attached. The aluminum tube has a diameter of 25mm and could be purchased…
Adapter not tested, designed based on theoretical dimensions. Needs testing Safety cannot be guaranteed! Treat this as last resort option. I recommend to seal with silicone / tape.
All the four pads are very same. Print with TPU, additional perimeters recommended.
CPU box for 6 pieces of Athlon/Phenom (Socket AM2) One file with both pieces (top and bottom). Print separately as depicted on the screenshot. I invite for to visit my webpage with links to social profiles and other computer activities at…
As already done by oceanreef for its masks, this adapter allows the mounting of 22mm filters for medical use, on the draining valve of the decathlon easybreath mask. This design is currently being tested. Used in combination with the…
The Valentine adapter for Decathlon face masks can be used by medical staff to protect from the COVID-19 disease. The functional design is inspired on Silvana valve from Vincent Groenhuis, inspired itself on Charlotte valve from Italy,…
Adapter is not tested, designed using theoretical dimensions, needs testing if fits nicely. Safety cannot be guaranteed! Treat this as last resort option. I recommend to seal with silicone / tape.
Print with durable filament: PETG or PLA.
This handy attachment allows you to clip in your decathlon snorkel to any goggles! Helpful if you lost the original clip or just want to attach the two together Enjoy!
Correa para los relojes de pulsera Geonaute W500, W700 y W900 vendidos en Decathlon. La hebilla es la original. Extraida de la correa rota. Strap for Geonaute W500, W700 and W900 wristwatches sold at Decathlon. The buckle is the original.…
Mounts a Profile Design Aqualite aero bottle to Profile Design T2+ DL aluminum aerobars . This setup allows you to drink on a ride without reaching for a separate bottle down below. It keeps you focused on the road and drinking more often…
Faite en sorte que vos objets dure plus longtemps en les réparant. Matière Petg buse 0.25mm, aussi valable avec une buse de 0,4mm. Utilisé le modificateur de Prusaslicer pour ajouter une surface rugueuse autour des percements sur les…
Ribbed lock washer for a Decathlon rear mud guard Rockrider Decathlon shop link . The washer parts got lost, as was the screw. This part fits the detachable part of Bahathor available under https://www.thingiverse.com/thing:5557395 .
A mount for the cheapest Decathlon handheld bike pump (ref: 8056700 ), designed for an O2Feel Peps N3 folding bike from 2016 (with the Samsung battery). It is equipped with 19.2 mm tube where it was mounted on the photo. It was designed…
Only another filter for Easybreath Decathlon. Warning! If you can not use any of these handmade adapters and filters, a certified device is certainly safer!!!
Changed rorys3D robust buckle to fit Decathlon's Nabaiji Xbase 100 swimming goggles (size S).
German: Adapter von einer Decathlon Pumpe zu einem Sub Ventil. English: Adapter from a Decathlon pump to a Sub valve.
As already done by oceanreef for its masks, this adapter allows the mounting of 22mm filters for medical use, on the draining valve of the decathlon easybreath mask. The design was conceived to be sealed with silicone to the body of the…
This file is a watch band/strap replacement (for the side with the holes) for "Ironman Triathlon Shock WR 200M" and possibly similar watch models (please be sure to check your dimensions before printing). Derivation: The watch model it…
After some time of use the dynamo lever gone broke, I try to make a copy to replace the original the file is not perfect! (but it work) printed a .1mm (detail) for tiny parts like screw printed in prusament petg (pla is too weak) infill…
A custom 3D-printable connector that lets you mount your Decathlon SL510 clip-on bike light directly to your seat post. Designed for a standard 31.6 mm seat post, angled at approximately 75° , this adapter provides a secure fit (see note)…
Print in something non-brittle (that means: no PLA) and slip two o-rings into the grooves near the edge, like in the photo. Stick on your pole tips to keep them from scratching your stuff during transport.
Despite the mechanism proposed by Decathlon, I was looking for an idea to create a support to secure the fixation of the 70cm pull-up bar from Decathlon. Decathlon uses a rotation pression system to lock the bar up between walls inside a…
This is a triathlon medal for our internally championship of our team. Dies ist eine Triathlon-Medaille für unsere interne Meisterschaft unseres Teams.
Replacement knife handles for knife from decathlon that uses the original screws https://www.decathlon.cz/p/lovecky-nuz-
For a Decathlon Caperlan 6m Travel fishing rod that I use as a mast for a ham radio antenna for SOTA/POTA. One part is to keep the mast upright (use on the lowest element of the fishing rod). The other parts are to hold the antenna wire…
I created this mounting system to be able to mount things to the outside of a Decathlon Quechua Airseconds tent. Examples are things like a Washing line, Tarp or even a Canopy. The Distinctive feature about this design is that both parts…
semplicemente ridimensionato
Set of clips for holding together the separated parts of the SUP Paddle (Itiwit Decathlon) Also compatible with any other 30mm paddle or any other cylindrical object (brooms, pipes etc.) I printed the clips from PETG but PLA will also…
This adapter allows to attach Olight Gober to the Decathlon Vioo clip.
My hand pump was older than the new model where Decathlon has introduced this adapter. I didn't want to throw away my pump, nor to buy the repair kit, because in the kit there are also other pieces I didn't need. So I just reproduced it.…
Adapter for Skoda Enyaq or other Volkswagen Cars to use the Decathlon ISO Cup in the Car. Diameter of the CUP 85mm
Quechua decathlon ultim comfort sleeping pad Schrader adapter For inflate pad through classic Schrader valve Print settings 0.2mm layer 6 walls 15% infill No supports
Holder for wireless blips for ~19.2-21mm internal bar ends (most standard TT bikes). Hardware required: M4 washer M4 30mm socket head cap screw M4 nyloc nut Thin piece of ~1 inch diameter heat-shrink for extra peace of mind that the blip…
--- Update Version 3 The strap always sliped out so I desigend a bad version 4 and a version 5, which consists of two parts glued together. This workes like a charm since 3 month. --- The famous french sports equipment seller forgot to…
Cap for the Decathlon Forclaz MT500 walking sticks. They are quite loud without any cap on the end when walking on hard surfaces (road or rocks) Therefore I modelled an endcap to print in TPU At 100% the model is a very tight fit. The…
Never let anyone else take your bottle by mistake. Especially useful when both your kids want the same exact bottle and then they can't agree who owns which. Or when they loose those bottles at school Sized to fit Decathlon 900 Ecozen ®…
The two parts to make from the Decathlon mask a breathing mask
charlotte Valve modified for non decathlon Mask (chinese model)
Soft flask drying stand for decathlon 250ml or 500ml soft flasks. There are 5 versions: 1x 250ml 1x 500ml 2x 250ml 2x 500ml 1x 250ml + 1x 500ml Print settings any rigid filament any nozzle size (0.4mm recommended) any layer height default…
Snaps in the 3DHydro mount and the bottom securely grabs the Decathlon water bag. It's got a little lip on the Decathlon side to avoid the bag falling off when handling while empty. I printed this with : Fiberlogy Impact PLA 0,2 layers 5…
Accroche de mini-sonnette décathlon Genre : https://www.decathlon.fr/p/sonnette-velo-500-mini/_/R-p-143045?mc=8346321&c=NOIR Il y a besoin d'une vis M4 et d'un écrou. (nouvelle version avec empreinte pour l'écrou) Mini bike bell mount.…
On connaît tous ce sentiment de frustration, au moment de refermer la portière de la voiture, quand on réalise un instant avant qu'elle claque que la boucle du sac à dos est restée en travers... trop tard :-(. Bien sûr, des boucles de…
🚐 Inflate your Quechua mattress with a car compressor This adapter allows you to inflate a Quechua Air Basic 140 cm 2-person camping mattress using a pump or compressor with a standard car tire (Schrader) valve connection . The original…
Hello Thanks a lot for the work provided by Vincent Groenhuis and his team for the awesome Silvana face mask adapter ( https://www.prusaprinters.org/prints/27214-decathlon-face-mask-adapters ) Here are some improvements/variants of the…
Part compatible with original Decathlon bag holder systeme Remove locking système and install it in New main frame Main frame - no supports - PLA or PETG infill 15% Hook - no support - PLA or PETG - ajuste infill to load up to 100% for…
Decathlon pull up bar lock basically locks the pull up bar from rotating PLA will probably do the job but I chose Fiberology ABS Plus and it works
Scope Cap for Objective end of Scope. Specifically fits Customized model for the Athlon Optics Ares ETR 4.5-30X 56mm.
Triathlon Trials - a minimalistic sculpture for the triathlete, biathlete, cyclist, or sports fan.