153 modeli
The original file that I remixed is this , I have added new features to test. I added new things to test like stringing test and the write on the bottom. You can also test a lot of other things: bridging bed level stringing calibration…
Retraction test I use for filament and printer tuning
Like me, if you dont have time, or just not enough filament, just use the smaller Temptowers. Based on the "All in One Temperature & Bridging Tower - PLA & PETG GCode included" from Tronnic, and the remix “Prusa Mini Temptower for PLA,…
Material-saving distance tower test model suitable for dialling in most of the printing profile parameters, including retraction, flow/extrusion rate, temperature, bridge, ironing settings, and certainly many more. Optimized for 0.4mm and…
This is basically an inverted standard calibration cube, and prints in about the same amount of time. But this one is hollow to test retraction, overhang angles, and an insanely difficult bridge at the top. The cube measures 20x20x20mm…
A simple and quick test print to tune retraction settings on your 3D-printer. Prints in 10 minutes on a Prusa. Inspired by older retraction test models, the base is only two layers high, and the cylinder in the center forces diagonal…
I designed these to be printed very quickly so you can test your retraction settings without wasting a lot of time/filament.
Nearly 50% Reduced Time and Plastic Plus Separate Models for Individual Tests All-In-One From 6h57m to 4h8m 44g of material to 23g of material Separate Model Print Times Diameter Test - 32m 25mm String Test - 28m XYZ Dimension Test - 39m…
I made this model for testing my retraction settings. I made a video about this on my Youtube channel: https://youtu.be/ed3zEa4WLTo Category: 3D Printing Tests
Activate firmware retraction in your slicer. Activate firmware retraction in klipper by adding this to you printer.cfg : [firmware_retraction] retract_length: 0.8 retract_speed: 60 unretract_extra_length: 0 unretract_speed: 60 Slice the…
Fast (8 mins) retraction test print, including a single-wall cube, and five towers. I had a problem with my extruder's retraction, and needed an object that was fast to print to diagnose the problem. Print instructions 0.4mm nozzle,…
1-6mm retraction tower that takes about 30 mins to print. Feel free to customize the gcode and edit the M104 command with your desired temperature. Credits: https://github.com/kartchnb/AutoTowersGenerator
I liked Stephen Albert's retraction test, but wanted something smaller that printed quicker (6-9 minutes rather than 15+). With rounded corners and only a thin strip of plastic connecting the two towers, it reduced the amount of plastic…
★·.··.·★ 👋 Hello😁 ★·.··.·★ Before reading the description I recommend in the future to look at the collections created by me for better service for high projects is to distinguish them better 💚MAKERWORLD→ COLLECTIONS 🇬🇧 RETRACTION TEST 🇮🇹…
No fancy settings, simple design. You can Support me by making a small donation: https://www.paypal.me/sharad1209
pequeño archivo para probar retracciones, en 3 tamaños
original model from https://www.thingiverse.com/thing:909901
petit test pour le stringing Print Settings Printer: Alfawise U30 Rafts: No Category: 3D Printing Tests
Fixes Creality CFS retraction issues with small spools that can't reach the bumpers on top of the CFS lid. It's a more comfortable solution to spool rings. Comes in 2 variants with different sizes from 1mm to 10mm. The size is the…
General Information The included .3mf file can be opened with the latest PrusaSlicer release ( https://github.com/prusa3d/PrusaSlicer/releases ) and modified for your hardware configuration in order to create retraction tuning gcode that…
Calibration de la rétraction avec une tour de rétraction (Fait avec Cura 4.12) La tour de calibration permet de faire plusieurs test de retraction en faisant varier soit la vitesse soit la distance de retraction. La tour se compose d’une…
This is just a small print to test your retraction on your printer. Category: 3D Printing
They are super easy to clip on and remove from the spring-loaded sliders inside the CFS lid. One is with SUNLU written on the top, other one without text. EDIT: Because of someone commenting 5mm is better than 6mm I added a 5mm version.…
Eliminate your stringing Simple but useful model for calibrate retraction values, one thing that helped me was checking also de values for de velocity of retraction, and the flow multiplicator. This model just takes 2 minutes to give…
Test your printer settings on calibration cube, bridge, overhang & retractions all at once.
Hi, all this is just a simple retraction test I threw together. When printing, it's best to start on a lower retraction value and build your way up slowly by something like 0.2mm each time, bearing in mind the max retraction you can get…
You find english below! Deutsch: Als erstes ist es wichitg zu sagen, dass ich weder das Modell, noch die Methode entwickelt habe. Bei einigen Projekten habe ich gemerkt wie umständlich das Einstellen des Retracts ist. Ich habe mir ehrlich…
Yet another retraction tower. Not really any different than most others. I designed it to run the tuning_tower command in Klipper to tune firmware retraction. Slice with a 0.2mm layer height, zero infill, 2 perimeters, 4 bottom layers and…
I designed this print with a thin base so you don't have to wait for it to finish before the pillars start. Its a nice quick way of checking your retraction settings super quickly with ease!
Retraction Test Towers with different distance between the towers. I usually start with retraction distance test. Then I use the setting/retraction distance (number of floor plan) that has the least ammount of stringing (after reviewing…
Simple retraction and stringing test for your printer. Every step can be used to indicate when and what settings have been changed with a script you added and help you find the correct value. Can be scaled up, down, be printed with…
use a .2 mm layer height I also recommend scaling it up about 10 to 20%
During my retraction testing I found out, that simple tower-to-tower retraction tests will tune retractions mostly for these specific geometries. But what if your model contains thin wall? Or some larger part with longer extrusion? You…
Use post processing plugin in Cura or other option in your slicer of choice. Height of the base - 1mm, height of the single block - 5mm.
You need to have good cooling and a perfectly tuned printer. If you dial in the retraction settings perfectly, you will be impressed how cool it looks. Pro tip: If there is a little bit of stringing a quick blast with a heatgun/hairdrier…
While there are surely plenty of retraction test prints available online, there aren't any that allow you to try different settings without printing multiple objects. With that in mind, I've created this customizable retraction tower that…
diameter : first circle:3mm second circle: 5mm square:4x4mm and last random shapes separated by 2mm the whole is 80x20x41mm (without a base 40mm)
The regular old retraction tower, it simply isn't enough. How many times have you tuned your retraction using a simple retraction tower, only to find your next print look like a spider's nest. This is where my tower comes in. (The above…
0.5-2mm retraction tower that takes about 40 mins to print. Feel free to customize the gcode and edit the M104 command with your desired temperature. Credits: https://github.com/kartchnb/AutoTowersGenerator
I had problems with the fan shroud, so I needed a directional overhang / curling test. It will test overhang at four angles (30 to 60°) in all directions for curling issues bridging at 30, 50 and 70mm arcs at 2.5, 5 and 7.5mm radius (5,…
I made this model because I wanted a better way to tune retraction. I needed to assess retraction performance on both small and large travels and be able to tune the retraction minimum travel (Cura), which decides the travel distance…
A 3D-printer torture test. Highlights cooling, overhangs, stringing, bed adhesion and more. Please note that this is not an easy print, ensure proper bed adhesion before attempting this. I wanted a model to use while finding the optimal…
This model gives you the opportunity to test the retraction and the dimensional accuracy. The left tower has an hexagon section (distance 10 mm) in order to check dimensional accuracy in various standard angle. The right tower has a round…
This is my TPU retraction test. There are many like it but this one is mine. I was trying to calibrate 75a TPE for my drag racer tires and standard retraction models were not cutting it for me. So i hopped into cad and made this little…
I test the model on prusa mini+ with the 0.4 nozzle.
Designed with using firmware retraction in mind. Tested with 0.4 and 0.6mm nozzles at layer hights up to 0.4mm. If a smaller nozzle is used, scaling it may be an option. First picture shows the default dimensions and distances, second…
The Advanced Retraction Test allows the user to tune retraction while taking into account variable distance. This uses 4 pillars that start at 5mm tall and increments by 5mm. 5, 10, 15 and 20mm tall. This allows you to change retraction…
Sub 10 minute printing basic retraction test.
----------------------------------------------------------- 🛠 PRINTING HELP & TROUBLESHOOTING ----------------------------------------------------------- ⚠ NOTES ⚠ • If Slicer errors and warnings appear, they should be ignored as they are…
Calibration Test Circular – Retraction & First Layer Check 🎯🖨 Not sure if your 3D printer is calibrated correctly? This Calibration Test Circular is here to help! 💡 Test your printer's retraction settings and first-layer accuracy with…
Here's my bare minimum retraction test, just three 4 mm wide towers 50 and 10 mm apart from each other. This is the fastest stringing test available. To get good adhesion print with 5mm brim. If you like this design you can like this, tip…
A tiny retraction test model. Includes 5 different gaps between the towers: 2.5 mm 5 mm 10 mm 15 mm 20 mm
Tune your printer's retract and bridging features individually or all at the same time. Good luck!
Remixed the original retraction towers to have a minimal base, saves minimal time and material. Original file by 3DPrintInGreece on Thingiverse: https://www.thingiverse.com/thing:4639020 Print Settings Printer Brand: Creality Printer:…
If your filament is not retracting properly (the spool doesn’t rotate) and instead unwinds inside the Qidi Box instead of going back onto the spool — this model fixes that problem. This spacer reduces excessive pressure between the…
A fast retraction test that also tests your printer's overhang up to 75°! This is a useful calibration test tool that uses less than 2g of filament! Feedback and Makes are always appreciated, If you're up for another challenge, check out…
Another quick test print to test retraction and get a calibration cube in 12 minutes on a Prusa. Measured from the base of the model, the cube is 10x10x10 mm with 1 mm thick walls.
A simple retraction test. Best test consistency with no infill. Uses very little material for base, so the test part itself starts quite quickly, easily within a minute. Print Settings Rafts: No Supports: No Resolution: 0.1-0.2 Filament:…
This is to help get you setting tuned right for retraction. layer height .2mm first layer .2mm 5 walls
I have designed these models and manually customised the G Code to print these tests with desired test parameters. Single wall models for speed, each model taking about 20 minutes to print. Stl files are included if you desire to…
Warning: please make sure gcode files are safe for your printer before using them. I take no responsible for any damage occur by the files. Use them at your own risk. I couldn't translate retraction value from…
Simple but effective calibration tower recommended to fine tunning your filaments! You can use one unit but I like to use two of these models around the bed in order to measure also retractions within model distance movements. IMPORTANT !…
Retraction has a very big effect on print quality, especially in infill and thin areas, and also, the correct retraction can vary quite a bit between materials, meaning it needs to be calibrated for each material – including the expensive…
A stringing test for your 3d printer to test it's retraction
Retraction calibration tower test dual tower H = 100mm
I still saw multiple weird artifacts in my prints even after dozens of successful retraction tests. To tackle those edge cases I designed this mini retraction torture test with multiple edge cases. On the top of the print you have quite…
A Retraction / Stringing Test collection How to print: I print this one on the Bambu Lab P1P with the following specs: Bambu Lab Standard Profil for the P1P 0.2 only the Layer width has been change Layer height: 0.2 Layer width: 0.4 First…
This is an example of what you can expect monthly through becoming a Patreon. On top of my 3D printed speaker drivers and cabinets, you also get practical 3D prints which don't require anything more than the filament itself. A geometric…
Flipped into the correct orientation version of the original model . Printing tips: Use 0% infill Use Seam painting tool in PrusaSlicer to achieve uniformal seam for testing:
a multi process tower to test retraction settings for each filament. Simply align the 6 stl files on top of each other and test different retraction settings for each stl :) watch my video to find out more: https://youtu.be/zJ9oxCkMkxk…
I've always been looking for a bigger test that has more than 2 towers. after several retracts i had the problem that my nozzle was clogged. With this file i can test the failure and would like to share it with you. The test only uses…
This is a more thorough stringing torture test. This prints best with a brim and tests both your printer and you slicer to reduce stringing in multiple directions. This is not originally my file. I would be happy to give attribution but I…
Retraction test model for those that dont have cura plug-ins
Print Settings Rafts: No Supports: No Resolution: 0,2mm Infill: no need Category: 3D Printing Tests
This is a functional calibration model, designed to test the effectiveness of extruder retraction speed and distance parameters on a 3D printer. The goal is to find the configuration that minimizes or completely eliminates the stringing…
Hello ! I created fast and quick retraction test. I use it for retraction tuning and it's very helpful. I added also single one tower and you can copy it and set range to another one by yourself. Feel free to comment and if You like it…
Most vertical meshes have lots of retractions, which takes time and can cause stringing. This model has none! Print in vase mode. For a permeable bottom, set the bottom infill to less than 100%. Print Settings Printer Brand: Prusa…
Ender 3 V3 SE Extruder Visualizer. Zeigt die Bewegungen des Motors für den Extruder. Die Retraction ist sichtbar. 5mm Innenaufnahme. Wird einfach aufgesteckt.
Got rid of the wording at the bottom of the retraction test and made the base of the test flat When you print a lot of these, I feel it adds unnecessary printing time Category: 3D Printing Tests
With this test you will be able to correct the retractions of your 3D printer On my printer with direct extrusion I use: Speed: 30m/s Distance: 0.8mm It depends a lot on the type of extruder and its quality, but in direct drive extrusion…
Test cones for stringing/retraction with single-layer base.
OpenSCAD allows you to easily design models based on logical expressions. When properly designed you can easily change your model until you are happy with the design. This example doesn't take too long to print and saves on filament. You…
I like this Retraction Test for different reasons, which is why I decided to remix it, to make it possible to callibrate the retraction within a few prints. The seam is opposite of each other. With many test towers I found that Cura…
Remixed the wonderful 10 Minute Mini Calibration Test for Oozing/Retraction at Different Distances by MrTestOne to also add bridging on the last layers. This probably takes more than 10 minutes now to build, but may be useful for some.
Mini design for using little material No support required
Added a bridge at the top. For bridging testing. You get it.
Just a quick printer test I made. I was tired of the majority of tests taking up to an hour to print. This design only takes 15-20 minutes on my CR-10S.
I tried tuning retraction setting for TPU. Each test is just in 8 minutes, but I needed to remove printed part and print part in new setting. I hope to start print for several setting at once, so I merged some settings. From the front,…
This is my take on a simple and effective retraction test model, designed to help you fine-tune your 3D printer's settings. Recommended Print Settings: Layer Height: 0.2 mm Infill: 0% Walls: 2 Material: Tested with PLA, but PETG should…
Not much to say. Just Download, Slice, and Print.
Test Super rápido para gastar poco material y tiempo Super fast test to spend little material and time
I have a Wanhao i3+ (with Microswiss hotend) which, let's face it, is a positively geriatric printer at this point. It's always struggled with getting clean seams on certain prints after a move, no matter how much or how little retraction…
This is a retraction test for large bed printers such as the Ender 5 Plus. It forces the head to move and retract across multiple objects near and far. First Picture shows the filament worms with a 4mm retraction at the fastest retraction…
It's a silverware drawer organizer. It's also a fairly useful retraction test that can help you tune your ideal temperature and fan for your filaments, though if you're a hardcore optimizer, you'll of course want something that tapers…
Retraction test stringing calibration - simple bed levelling Are you sure your 3d printer is printing well? Try this retraction test and check the result. It will be ready in a few minutes! It's only 60x20x6.8 mm This is a simple…
A list of changes to the original model are listed below.
![[Flipped] Fast Stringing / Retraction Tests](https://media.printables.com/media/prints/837786/images/6453771_3d35048d-8fed-4942-8f0d-fe2cf30c0954_c924ab62-fc60-48db-91f5-c02c147b34e5/stringing_test_v1_2024-apr-09_11-32-12am-000_customizedview1378487328.png)
