P
Printablesvvision
PAM81610 Amplifier Case
Simple case for PAM8610 amplifier. Tight fit around the board. Button size is 15x10mm. Photos show PLA draft print of 0.3mm with thin wall detection.
- Pobrania
- 258
- Polubienia
- 18
- Ocena
- 5
Wyniki wyszukiwania: 1610
Liczymy pasujące modele…
P
Printablesendoril
Body holder spare piece for 1:16 RC car (SCY 16101, 102, 103 etc.) (.scad file included)
When this little beast lands on rooftop, this piece can easily break. I designed a spare, much stronger part. Fitting perfectly with 0.2mm layer height print. Make sure you slice with 100% infill. No need for supports. No need for raft or…
- Pobrania
- 220
- Polubienia
- 41
- Ocena
- 5
P
Printablesthall72
Lego Compatible (11610.dat) Cone 1 x 1 Inverted with Shaft
This model is compatible with the lego system.
- Pobrania
- 171
- Polubienia
- 21
- Ocena
- 0
P
PrintablesAl Williams
Clamp for CNC 1610
I bought a cheap 1610 engraver (the LinkSprite, but honestly, I think they are all the same). It had some wing nuts for clamps but it was hard to get things to hold still on the bed. Print 4 of these and use the wing nuts to secure to the…
- Pobrania
- 102
- Polubienia
- 15
- Ocena
- 5
P
PrintablesRobinson
WaveShare 5.5" amoled touchscreen WV16103 Case (not finalized)
Simple protection pour l'écran tactile WaveShare 5,5 pouces amoled (modèle WV16103), pour lequel je n'ai quasiment pas trouvé de modèle imprimable sur le net. Le but à terme est d'intégrer des pieds (ou un système d'accroche), ainsi qu'un…
- Pobrania
- 89
- Polubienia
- 8
- Ocena
- 0
P
PrintablesPontus
holder for heatgun (Steinel hl1610s)
prints with no supports
- Pobrania
- 83
- Polubienia
- 13
- Ocena
- 5
P
Printablesctheroux
CNC 1610 Improvements
This project contains 5 improvements for a 1610 CNC. These improvements were inspired by the following YouTube videos of JJ Hontebeyrie: https://www.youtube.com/watch?v=NNrqx62lyBI&t;=602s https://www.youtube.com/watch?v=_gX_YCsN4wo 1.…
- Pobrania
- 58
- Polubienia
- 11
- Ocena
- 0
P
PrintablesNovaMaker
Grandstream stand 1610
Stand para el grandstream 1610 Print Settings Printer Brand: Hellbot Printer: Hellbot Magna 2 230 **Rafts:** No Supports: Yes **Resolution:** 0.2 Infill: 10 Category: Tool Holders & Boxes
- Pobrania
- 56
- Polubienia
- 2
- Ocena
- 0
P
PrintablesRenba
3018 Rail Snap-on Durst Cover (also 1610, 2040, 2418,... series)
Hi ! Bored about dust falling into the rail of your favourite 3018 CNC and family ?... A simple snap-on dust cover (but it takes time to design in order to have a good snap-on effect and left the maximum space under the cover for cable)…
- Pobrania
- 54
- Polubienia
- 6
- Ocena
- 0
P
Printablescperiod
CNC 1610 pen holder
I tried another pen holder for my CNC, but I found that it didn't have any support near the pen tip, and the style of pens I'm using (Staple's ultra fine tip permanent markers) really don't draw well without support. I've started using…
- Pobrania
- 46
- Polubienia
- 4
- Ocena
- 5
P
Printables@doegox
CNC 1610 ChipSHOUTER Holder / Mount
Here is a mount for the ChipSHOUTER, a electro-magnetic fault-injection tool, to fit a classical CNC laser module mount. If your CNC mount doesn't have the notches to fit a square laser module, you can easily adapt the design to be shaped…
- Pobrania
- 38
- Polubienia
- 4
- Ocena
- 0
P
PrintablesThomas Lampertius
BCMaster 1610 Microphone Horizontal Stand
BCMaster 1610 Microphone Horizontal Stand
- Pobrania
- 23
- Polubienia
- 0
- Ocena
- 0
P
PrintablesKrzysztof Grabania
Seat Leon 5F 5F0071610/5F0071610A replacement parts
Full instruction with list of individual parts for Seat Leon 5F 5F0071610/5F0071610A Aero Side Skirts Mounting Kit is not available to order separately without Side Skirts. Also Side Skirts are rarely available to order from the dealers.…
- Pobrania
- 22
- Polubienia
- 4
- Ocena
- 0
P
Printablescperiod
CNC 1610 Z carriage
I managed to strip the bolt for tightening the spindle on my Linksprite 1610 CNC. I decided to take the time to model up an entire replacement carriage (with help from a few measurements ). Features: the carriage is entirely parametric.…
- Pobrania
- 21
- Polubienia
- 5
- Ocena
- 0
P
PrintablesReid
CNC 1610 X Axis Endstop
Be sure to align the X stop so that it is in front of the X-axis shaft coupler. This is a very basic X axis endstop for the 1610 CNC. Leaving the STEP file here so others can remix as they please. Print it with whatever you want and…
- Pobrania
- 21
- Polubienia
- 3
- Ocena
- 0
P
PrintablesAdrian Rodriguez
Gripper adapter KUKA VKR16 R1610-2 (CYBERTECH) - SMC MHZ2-25C
Adapter for the robot KUKA VKR16 R1610-2 (CYBERTECH) to hold the gripper SMC MHZ2-25C. The blueprints of the gripper are on the photos.
- Pobrania
- 21
- Polubienia
- 0
- Ocena
- 0
P
PrintablesDirk
CNC 1610 - Electronics Enclosure
Controller board enclosure. I've designed this so that you need to remove the spacer pieces from the board. The PCB can be secured via M3 x 8 mm screws to the enclosure, not additional requirements on there. The cable cover snaps in…
- Pobrania
- 17
- Polubienia
- 3
- Ocena
- 0
P
Printablescperiod
CNC 1610 upgrades/remixes
A collection of assorted upgrades for my Linksprite 1610 CNC. remix of Despair's Z plate to add a tab to tie the endstop wires to; wires connecting to moving parts like to break without strain relief. remix of Despair's X mounts to put…
- Pobrania
- 14
- Polubienia
- 1
- Ocena
- 0
P
PrintablesWillibald4711
AVM Fritz Repeater 1610 Outdoor Regenhaube
Regenhaube zum Schutz vor Regen
- Pobrania
- 14
- Polubienia
- 0
- Ocena
- 0
P
Printablesendees
SG116/SCY 16101 pro bumper mounting
Bumper mounting part for front and back bumper for RC car SG116 PRO/SCY 16101
- Pobrania
- 13
- Polubienia
- 1
- Ocena
- 0
P
PrintablesXed
1610/T8 CNC Z and X axis Bearing Blocks
I was hunting around for things to make my 1610 a little more sturdy (mostly as a way to avoid spending money on a 3018) and came across TRAXA's bearing block. It wasn't set up for the bearings I had on hand so I had a go at recreating it…
- Pobrania
- 12
- Polubienia
- 2
- Ocena
- 0
P
PrintablesDirk
CNC 1610 - Revised PSU Holder
PSU Holder for CNC 1610 machine. The previous version I had was functional while this one looks a bit better while attaching to the 2020 extrusion as the previous one. The holder fits the stock PSU supplied with the CNC engraver. Print…
- Pobrania
- 11
- Polubienia
- 0
- Ocena
- 0
P
PrintablesAdam Coddington
1610 CNC 55mm Spindle Mount
It doesn't take much to outgrow the stock 775 motor that most 1610 CNC machines come with. Using this adapter you can move past the stock motor's limitations by mounting common 55mm diameter spindles. There are two versions of this part…
- Pobrania
- 9
- Polubienia
- 0
- Ocena
- 0
P
PrintablesAdam Coddington
1610 CNC Optical Zeroing System
If you own a CNC mill without automatic end stops, you've probably had to restart a few jobs from the beginning because you over-ran where your end stops would've been, or you did something that set off your CNC mill's alarm. This optical…
- Pobrania
- 9
- Polubienia
- 0
- Ocena
- 0
P
Printablesdeluc
Pelicase 1610 Handle improvement
This is a handle attachment for a Pelicase 1610 handle. It makes carrying the heavy pelicase way more comfy. Printed in TPU. After attaching it to the handle I inserted three little screws into the holes in the original handle.
- Pobrania
- 9
- Polubienia
- 2
- Ocena
- 0
P
Printablescperiod
CNC 1610 TLO switch holder
One of the side-effects of adding bed risers to my CNC is that I can pass the front edge of the bed slightly, which makes it a convenient place to mount a microswitch to use as a tool length offset probe. This mounts to the front,…
- Pobrania
- 8
- Polubienia
- 0
- Ocena
- 0
P
Printablescperiod
1610 CNC ziptied X/Y endstop mounts
Tried some other endstop mounts, but they were more complicated than I thought was necessary and tended to stick out too much. These are about as minimalist as you can get without just gluing the endstop directly to the rail bracket. Clip…
- Pobrania
- 6
- Polubienia
- 2
- Ocena
- 0
P
PrintablesEasy Target
Simple 55mm Dial Gauge holder for 42/45mm spindle CNC's (eg 1610)
Lots of dial gauges seem to have a 55mm body and the back plate 8mm offset from the pin. My cheap (unbranded..) one certainly fits that category. This is a design to let me mount it in my CNC so I can level PCB's before cutting tracks…
- Pobrania
- 5
- Polubienia
- 1
- Ocena
- 0
P
PrintablesEasy Target
1610 bed lift plates for underbody sliders and better ER11 clearance
Combined with some 50mm tall feet (like this: https://www.thingiverse.com/thing:2250758 ) these blocks allow the 1610 Y axis rods to be re-mounted below the frame rail. and the bed brought back up to a sensible height. Perfect if you are…
- Pobrania
- 5
- Polubienia
- 1
- Ocena
- 0
P
PrintablesPCHadaptivegaming
Storage Pieces for iSeries 1610: Adaptive Gaming Kit
LidStorageGrid x4 LidStorageMount x7 LidStorageMountTall x1 WallCornerLeft x3 WallCornerRight x2 MiddleWall x2 MiddleWallCentered x1 StorageWallLong x3 StorageWallShort x2 For use with iSeries 1610-10 Case with no inserts.…
- Pobrania
- 4
- Polubienia
- 1
- Ocena
- 0