Liczymy pasujące modele…
A pencil vase for decorative purposes to hold pens and pencils, or anything else. It is 113mm tall and 100mm wide. Print time approximately 2 hours with a single wall at print speed of 50mm/s. The photo shows the vase printed in vase…
This model is compatible with the lego system.
This model is compatible with the lego system.
This model is compatible with the lego system.
This model is compatible with the lego system.
Mechanic fast for Meiho Versus 7070 & 7050 Print with PETG
The stand does not require any additional parts or gluing. It fits and prints well on the Prusa MK3 in 0.30 mm draft mode with “build plate only” supports and 20% infill. It uses a screw holes of MC-707 and has an additional tab for…
Překreslil jsem zakoupený originální klip pro LED svítilnu Peli 3315 tak, abych jej mohl vytisknout a dodat našemu spolku dobrovolných hasičů na jejich nové zásahové přilby za přijatelnější náklady. Oproti originálu jsem musel zesílit…
The Boeing 707 is a significant milestone in aviation history as one of the first successful commercial jet airliners. Introduced by Boeing in the late 1950s, the 707 revolutionized air travel with its speed, range, and capacity. It…
The food processor does NOT work if the bottom of this piece is broken off, and mine keeps breaking off. So I modeled this up so that I could replace the original part. Works good enough in mine. Edit: Updated as the original bent into an…
lego 3070 3069 63864 2431 6636 4162 14719 3068 26603 87079
Remixed from "Dewalt and Craftsman Case Dividers" by benjamenjohnson (thing:3480845) adjusted the heigh to fit this larger Tough Case+. Print Settings Printer: Ender 3 V2 Rafts: Doesn't Matter Supports: No Resolution: 0.20mm Infill: 15%…
The lock system for cover for Meicho Versus fishing boxes. Use magnets in caps 10*6mm Print instructions Use the 0.15 layer height or lover. Your can print with 0.2 layer, but thread is not cool quality.
This model is compatible with the lego system.
Hab diese Boxen nun seit drei Jahren im Einsatz und mich jetzt entschlossen, sie hier hochzuladen. L und R sind für die linke bzw. rechte Seite passend, und die M-Modelle passen in die Mitte. Als Scharnier nutze ich Klebestreifen in 15 mm…
Hey, i made this little sawdust adapter thing for the DeWalt 707. maby it works for other saw's but i don't know. It fits well without any screws or anything, the layerhight holds it in place. the output tube has a outer diameter of 27,3…
The TP-Link ER707-M2 router is just slightly wider than a 10 inch rack slot. This design is one way to mount the router in a 10 inch rack with a serviceability trade-off. It takes an opening of 4U to insert/remove the router using about a…
2 of the wall mounts are required and screw into the PC using existing M3 holes. Print 4 of the drill guides to help drill holes into the wall with the correct spacing and then either screw into the wall using those screws or print 4 non…
Inspired by @RobKenny_363449 (Inlays) and @ZbynekKral (Box) to get my stuff organized in Sortmaster Light ( https://www.stanleyworks.de/produkt/stst1-70720/stanley-sortmaster-organizer-mit-10-faechern ) See Pictures to identify your…
This model is compatible with the lego system.
This is a cover that slides onto a pair of needle nose pliers to keep them from damaging surfaces and from injuring you. This design was specifically made for the DeWalt DWHT70799 pliers. These pliers have been discontinued, but these are…
Got a request to design a spare spool for the discontinued Big Baitrunner XT-A Long Cast from Shimano (Item code RD14707) After some iterations this is what seems to work best. Optimized for FFF. Tight lines!
Druck in TPU / weich, 0.16 Layer Höhe. Beim Drucken das kleine Teil zuerst drucken, dann beim großen Teil bei Höhe 5,3 mm pausieren und das kleine einfügen. Dadurch kein Support nötig :-)
Remix of Stanley SortMaster Junior (1-97-483) by @mirabatek . Enlarged version of insert box for Stanley SortMaster MINI Box (STST1-70720) to 55.5 mm. Print instructions: Material: PLA Filament: AURAPOL PLA 3D Filament L-EGO Yellow Layer:…
This model is compatible with the lego system.
Der orginal 20 polige Motorstecker war nicht mehr zu beschaffen. Modell hat nicht perfekt gepasst aber der Bajonetverschluss hat funktioniert. Die orginal Pins können noch bei BMW gekauft werden. Orginal Gummituell ist noch verfügar und…
Guard lever for Dewalt DW707 as well as Elu Ps274. Prints in two parts. Part two is a small spacer ring that glues on one side to eliminate the need for supports on the bottom surface. The rest of the part will need support. Print…
These are some Inserts for the Dewalt TSTAK Drawers, they sit inside the drawer sections allowing you to put smaller items in, they have lids as well to stop spillage when you carry the drawers on their side. There are options: - Single…
This model is a direct replacement for a plastic stem driver that tends to break in some Kohler-brand shower handles. Recommend printing in PETG or ASA for strength. Original part tends to break at the edges of recessed square drive, this…
7074-musei-civici-di-venezia-relief Category: Sculptures
NOTE FOR CONSTRUCT PRINTER: plz keep the infill at 13%, HERE is the assembly process:_ NOTE:-Assembly process may require some force.SO, PROCEED WITH CAUTION. 1.First Step:- insert the forward into the rear part using the premade pin. 2.…
Ich habe dieses Modell erstellt als Ersatzteil für die Lüftungsgitter Rechts und Links im Passat32b oder Santana. OEM 321819707C die Dateien sind einzeln als STL zu laden, als Druckplatte mit alles Teilen oder als Datei mit drei…
Yesterday at the gas station, I noticed that this thing had broken, and now the fuel filler flap wouldn't close. I decided to buy the OEM part online, but the price of £25 without shipping shocked me. Then I decided to find a 3D model…
I bought this drone and immediately lost one of the legs. So I modeled a replacement and printed in TPU. Please mind the TPU was not dry so the quality on my print is bad.
Parametric OpenSCAD design to generate enlarger masks for Durst Sivoneg/Sinoneg/Sirioneg/Unineg carriers. Print two to sandwich your film, or print one if you have a sheet of glass in your carrier.
Use double-sided tape to attach
For this project I used a mt3608 boost converter to boost the 5V from the USB-C power source to 7V. Assembly is pretty much straight forward. Print 1 bottom and 1 top half, then 2 contact holders of which 1 has to be mirrored. The…
I recently got a used HK-706 with the original cable clamp missing. A fellow radio amateur sent me pictures of his original clamp, so I designed a replacement in FreeCAD. I printed it with black PLA and variable layer length to smoothen…
INTRODUCTION: This is a ring gasket mount case for the Hexgears GK707 keyboard. INGREDIENTS: Hexgears GK707 plate and PCB 5mm diameter gasket material (e.g., silicone) for the top part of the case. A length of about 350mm should be…
A lamp stand designed for Steve's Vase 707 model. It allows you to use the Vase 707 as a table lamp. You can download the Vase 707 model here. https://www.printables.com/model/310118-vase-707 You need to press it with support to ensure…
Print time: 5h 35min Infill: 15% Wall thickness: 2mm Material used: 97g
The plastic hub on the shredder disc of our food processor fell apart and there doesn't seem to be a convenient way to buy a replacement in Canada. My wife just assumed I'd design and print a new one; she may be a keeper. Print Settings…
This is a revision of an earlier case posted here: https://www.thingiverse.com/thing:4823463 I found the original edges of the case too sharp, so added chamfers to reduce the risk of laceration. Category: Electronics
Porta avvitatore a batteria BLACK + DECKER A7073-XJ
This is a simple holder to store three IKEA cork pot stands (19 cm, item number 87077700) under a table or desk. It saves space and keeps the pot stands easy to reach. Mount it with 3 mm screws (2–3 cm long). Print Settings: Print with…
A small holder for an M.2 E key to 4x SATA controller for mini PCs like Dell Optiplex 7070 micro: https://aliexpress.com/item/1005009548263440.html This allows upgrading this mini PC to a DIY NAS, only works if the m.2 NVME slot is…
Saw the E-foiling become more mainstream and decided to try it as a hobby. Bought the cheapest new board and tried to convert it into a E-Foil board. There aren't many builds with Flipsky 7070 motor, however in theory it should be…
The plastic spacer that attaches the handle to the glass lid broke on my DeLonghi DCP707 slow cooker . I designed a new one and printed it with colorFabb HT (a high-temp PETG rated to 100*C). The print would also work with ASA, ABS or PC…
The safety latch on the lid of my Hamilton Beach 12 cup 70725a model food processor broke. I designed and printed a new one out of PETG (given the heat from the dishwasher it seemed appropriate vs. PLA). Make sure you dry fit everything…
Merloni ( indesit ) refrigerator fridge freezer drain flap valve 14mm part number C00857077 I made it from TPU A95.
This allows you to rebuild your charcoal canister and make it future serviceable at the same time. Sand ~1/16" off the bottom of the canister, tap around the edge to break the bond and remove the old bottom. Use epoxy to install the…
This model is compatible with the lego system.
These are some Inserts for the Dewalt TSTAK Drawers, they sit inside the drawer sections allowing you to put smaller items in, they have lids as well to stop spillage when you carry the drawers on their side. There are options: - Single…
I recently got a used HK-706 with the original cable clamp missing. A fellow radio amateur sent me pictures of his original clamp, so I designed a replacement in FreeCAD. I printed it with black PLA and variable layer length to smoothen…
I made this because my clutch petal broke and they don't make the clip so I made it myself. Do about 20% infill and hexagon infill and my printer can't do the final one and I made it strait because I have the Adventurer 5M printer and…
This model is compatible with the lego system.
This model is compatible with the lego system.
Der orginal 20 polige Motorstecker war nicht mehr zu beschaffen. Modell hat nicht perfekt gepasst aber der Bajonetverschluss hat funktioniert. Die orginal Pins können noch bei BMW gekauft werden. Orginal Gummituell ist noch verfügar und…
Yesterday at the gas station, I noticed that this thing had broken, and now the fuel filler flap wouldn't close. I decided to buy the OEM part online, but the price of £25 without shipping shocked me. Then I decided to find a 3D model…
Překreslil jsem zakoupený originální klip pro LED svítilnu Peli 3315 tak, abych jej mohl vytisknout a dodat našemu spolku dobrovolných hasičů na jejich nové zásahové přilby za přijatelnější náklady. Oproti originálu jsem musel zesílit…
Before you go further! This model is available for free for all my supporters in Printables Club 🧡 Consider joining my club to have access to all ⭐⭐⭐ exclusive projects ⭐⭐⭐ and be part of my community! This project is for personal use…
This model is compatible with the lego system.
This model is compatible with the lego system.
This model is compatible with the lego system.
Before you go further! This model is available for free for all my supporters in Printables Club 🧡 Consider joining my club to have access to all ⭐⭐⭐ exclusive projects ⭐⭐⭐ and be part of my community! This project is for personal use…
These are new legs for the 70" LG TV (Model 70un7070pua). You will need to buy hardware if you don't already have some, these take (6) M4 X .7 bolts (Around 20mm long (1 1/2in) and you'll need some washers too. FYI, the size and thread of…
PETG, 0.2 to 0.4 line height, walls count to 100% infill. Tested with 3500W motor power on DYI efoil, total 100km distance OK.
Wall holder for Nexa remote control PBT-707. PETG recommended. Do not print in brittle material such as PLA because the side clips will break when inserting the remote. I also recommend printing the two parts dovetailed version in order…
This model is compatible with the lego system.
I made this because my clutch petal broke and they don't make the clip so I made it myself. Do about 20% infill and hexagon infill and my printer can't do the final one and I made it strait because I have the Adventurer 5M printer and…
This model is compatible with the lego system.
Ever had second thoughts about putting a can or bottle in a bag when going anywhere? The beer pod might ease your mind a bit. Please post your stories in the comments section! Update : 2017-12-09 Added a bottle version. Fits all the…
Dimensions : lenght :47 cm – 18,5 inchs wingspan : 45 cm – 17,7 inchs SCALE : 1/ 96 Although it was not the first commercial jetliner in service, the 707 was the first to be widespread and is often credited with beginning the Jet Age .…
Servo mount for Graupner 707 servos. This mount can be glue/attached to the servo plate (also found on my page) or simply mounted in the airplane. The servo is meant to be on its side. Category: R/C Vehicles
I opened old hp inkjet printer/scanner combo and found this neat WiFi module inside. Then found out it can be used as USB WiFi-Adapter. The original design required you to make a tiny adapter PCB with USB-A male plug. Since I haven't got…
These pickup rings were designed to fit a specific combo of EMG 707 pickups and an Ibanez RG where the neck pickup sits against the neck so the ring can't go all the way around. They are purely for aesthetic reasons and really serve no…
Made up some port covers for my 12hp Briggs and Stratton Vertical engine (281707), used them for storage while the carburettor and exhaust were removed. also used the covers for painting, they are in no way perfect for each application…
Replacement insert plate for the DeWalt WD707 mitre saw. Should also fit DW701, DW709 and DW711. Original part number 861925-02 There is one version that is 34cm long, and another split in two that should fit the print bed of the Prusa…
An easy-access wall mount for your favorite 3-in-1 controller/keyboard/mouse! Slotted in the bottom for easy removal of the controller. This model can be printed upright (as it would be mounted) without supports.
I made this because I don't really need the "tough case" and I wanted the bits easily accessible in a draw taking up a little less room. I didn't find anything that held these bits in this way so I just threw something together, it isn't…
The clip for the steering column cover breaks easily and at that point you either live with the ugliness, you buy a brand new cover or… you 3D print this! I recommend you print using black ABS.
71052 Adapter - Emulates a Welch Allyn 72200 Battery 70752 Adapter - Emulates a Welch Allyn 72000 battery The goal of the design was to use a minimum amount of materials and tools to assemble. These adapters were created for a quick…
![Stanley SortMaster MINI Box (STST1-70720) [REMIX]](https://media.printables.com/media/prints/759486/images/5921994_8c1028df-0474-4f09-974d-9af0b0d778b8_47c920f5-5712-4d5a-b606-524cadd66588/img_20240210_173710376.jpg)
