Liczymy pasujące modele…
The Fosi Audio V3 Mono is an incredible piece of engineering, but it uses its entire aluminum chassis to dissipate heat. When sitting flat on a desk or stacked, airflow to the bottom of the unit is restricted. This stand helps solve the…
Replacement foot pad for Quilter 202 Series Amp / Amplifier Head! Tested on Overdrive 202, but should work for Tone Block 202.
Just a simple replacement rotary knob for the Pioneer A-616 Mark Hi-Fi amplifier. Printed in PLA with 25% infill, 3 walls and 0.1 mm layer height. No Supports are needed because of the shoulders.
It is a Chickenhead knob for the power control on the Boss Katana Gen 3 50 Guitar Amplifier Combo.
The iPhone 16 Pro (and I'd predict more than a few others) has audio coming out from the top and bottom of the phone. Most of the “speaker” models I've seen only utilize the bottom speakers for audio. This model allows for “near” stereo…
A model i love just few modification on it, thanks to tizyx Collections available Losi MicroT Spinner & Fidget Arrma RC Earrings
YDA-138 based amplifier chassis Suitable for entry-level radio hobbyists.
I printed this on a Prusa Mini using Inland PLA+. It's designed to be easy to print. Set the base flat and right side up, supports suggested for the base insets for the rubber feet. Set the cover upside down. Generate supports at…
Die meisten Handys liefern einen Stereosound. Mein Passivverstärker unterstützt diese Soundausgabe. Mann hört sehr gut den Stereosound. Viel Spass damit. Most cell phones deliver stereo sound. My passive amplifier supports this sound…
Bodykit designed for the CTM AP7 kit on the AAP01 platform. Both a version designed for sound suppression and amplification are available. General The kit mounts via a locknut that is screwed onto the stock AAP01 barrel. This uses the…
I made this do then I can dominate the field with a lousy gun. The shots sound scary while shooting and it works. This is a 14mm ccw threaded amplifier designed for only 14mm ccw threads. This works and is perfect. Print this as 101% (one…
18650 battery PAM8403 WC amplifier TP4056 charging board 3.5mm jack KF301-0.5-2P - 2 in. terminals KCD11-101 switch
Many desktop 2.1 speaker systems place the amplifier electronics inside the subwoofer enclosure , which then distributes amplified signals to the satellite speakers, like the Trust Tytan subwofer shown in the photos. When the amplifier…
I made this to upgrade the binding posts in my Yamaha M-4 amplifier to support banana plugs.
I have a massage table and mounted transducers to the bottom of it to make a sound bed. I needed a holder for my Fosi Audio TP-02 subwoofer amplifier to hold it on the side of the table. Obviously, there were no designs this specific, so…
As part of my son's GCSE project last year he had to design and make a passive amplifier. He experimented with a number of different shapes and a continuously expanding tube generated the best overall sound. He left a 3d printed version…
XT60 female connectors can be glued for speakers outs and circle hole for 5.1x2.1mm connector for CC/CV 12.6 charger. Also you can mount 3S 18650 battery inside using double side glued tape. For good PCB fit in case unscreaw two screws…
A simple model of a Pioneer GM-4 Component Amplifier from the Lonesome Carboy 1 series. Good for modelling holders, facias, whatever
Toroidní transformátor 230/20 100VA kondenzator 10000uf 50v UNISIAN LCD Player Module MP3 28*64 Display Bluetooth Digital Audio Decoder Board TDM157 USB SD BT FM for Car Home Amplifier GBU8K-DIO / 800V / If 8A /Ifsm 180A TZT MH-ET LIVE…
Simple no nonsense surface flush mount plate. Will work for ZK-502 and ZK-1002 amps. I have provided a version for both the MT and T versions. ** Please note there are two amp versions! Check which model variant you have to be sure of…
Small enclosure boxes for MAX4410 headphone amplifier boards, which you can get for cheap from Aliexpress. The lid is designed to be snap fit and can be closed relatively easy, but for opening it you may need to help yourself with…
This is a 13/16" wrench to tighten the retaining nut on a jewel light assembly commonly found in Fender style amplifiers. I've made the belly slightly wider than the mouth to improve the grip on the nut. Print Settings Printer Brand:…
Fairphone 2 Stand Passive Amplifier You'll need 2 x 3 mm magnets with 2 mm depth (1 for the body and 1 for the door)
4 tuercas m3 4 m3x6 2 m3 Print Settings Printer Brand: Creality Printer: Ender 3 Pro Category: 3D Printer Parts
Case / Enclosure for Digitalkey Wuzhi Audio ZK-502C Bluetooth 5.0 Wireless Stereo Audio Amplifier Board – 2x 50W, 2 Channel Use the screws and spacers that came with the amplifier board kit. All our designs are free to download and use –…
Hey y'all. I designed this trippy little acoustic phone amplifier so you can jam out all summer long even if you don't have a bluetooth speaker. It prints in place with no assembly required. Hinged kickstand allows you to rock the amp…
The complete guide for the project: https://www.maschinfo.de/IR-Verst%C3%A4rker
Two years ago I got an idea to build myself an audio amplifier. I made one based on TPA3118 from TI. Then I made a cd player/bluetooth reciver using raspberry pi. To case it all I designed a wood+plastic enclosure to print and assemble…
The Fosi Audio V3 Mono is an incredible piece of engineering, but it uses its entire aluminum chassis to dissipate heat. When sitting flat on a desk or stacked, airflow to the bottom of the unit is restricted. This stand helps solve the…
Hello here is a universal box for Lilygo T-beam cards. Some short tests with water projection and immersion. The box resists well, no trace of water in the case. with sma or ipex plug for the T-beam , sma plug output. 25x25 gps antenna ,…
TPA3110D2 Bluetooth Amplifier enclosure. I added connector terminals to the board, had to bend the wires of the terminal block wider for the middle power terminal. Added a second design for when you solder the wires to the board and did…
Enclosure for TPA3116 Bluetooth amplifier board You need to print 5 of the button pins. Use a brim to stop warping of the top and bottom enclosure, and for the button pins as it is very small. Note 1: Clean the 5 holes for the button pins…
It's a comb with parametric tooth to ease the use of graphic equalizer. You can edit the scad file to suite yours. Alter the number of tooth, their width/height and make your preset.
Voici la modélisation de l'amplificateur AB-IOT -433 pour le futur lora APRS BOX. @Désolé pour la précision. Don't forget to indicate that you like the model on printable.com. Please send your opinions for future improvements. and take…
Full details and a build guide is on Instructables! Electric Musical Instrument 3D Printed Amplifier . Print with your favourite thermoplastic | http://e3d-online.com/All-Filament Love 3D printing? Love T-Shirts? Then you need to check…
A bracket to mount the amplifier of the WeBoost system (single user variety). The booster comes with Velcro to mount it, but it didn't work well. So, I came up with this that needs screws to mount it. There are various bracket versions…
Remix for an amplifier case. Original one doesn't fit in several ways.
I reverse engineered this small amplifier knob for someone who needed a few for his "Peavey VTX series guitar amplifier", using the original as a reference for measurements. Maybe someone else might be interested too. They are designed…
This model is for the MB2 Stereo Mic Booster My dad had a lot of cables all over his desk and he wanted a simple way to get them out of the way. So I quickly designed this in sketchup to mount it under his desk. The screw holes are 6mm in…
Passive Horn Amplifier for Smartphones. No Amp, no Batteries, just physics ;-) Prints without supports!
Remix of gexgecko's Passive Speaker/Amplifier with a flat back so it can be attached to a wall with Command Strips
As the Louder ESP32 module has the same size as a Raspberry PI I remixed my Pi 4 case. The board can be screwed down with 2.9mm screws or M3 bolts and the top of the case can be fastened with “M3 X D5.0 X L4.0 heat set inserts” and M3…
No Supports are needed for the Phone Stand. I have added in my own support that snaps off easily. There are a few options to print. the names are self explanatory but I will still give you a run down. Phone Stand - No Case: this is for…
A cooler for a Narda LNA to help maintain a steady temperature to maintain a steady S21 power level (around 36dB). Without a heatsink, the Narda LNA (Model Number: LNA-30-04001200-15-10P) heats to around 60c and has a S21 power loss of…
I couldn't get the original model to fit my G2, so I remade them in Fusion 360.
Second version of my amplifier case ( first one ). This time even smaller, as a result of switching from transformator to SMPS with voltage regulator after it. If you are interested all schematics for amplifier etc are attached to the…
Replacement foot pad for Quilter 202 Series Amp / Amplifier Head! Tested on Overdrive 202, but should work for Tone Block 202.
This amplifier is used to tighten the profiles and give additional rigidity to the profiles under the groove 2020 Recommended printing options: * Layer: 0.12mm - 0.16mm * Filling: 45% hydroid * Number of perimeters : 6 pcs. * Material:…
Panel for amplifier., printed with a 0.4 mm nozzle. Made for personal use, but someone may need it
HW-408 Amplifier ventilation case with exposed outputs and potenciometers Shortly the case for a HW408 class-D amplifier
I'm new to creating , your best print would be around 12" by 8" with 15% infill .42 wall thickness.
Genius GX Gaming SW-G2.1 1250 - amplifier mount Simple mount for amplifier. Possible to mount on the bottom of table. Side mount also possible. You can use both types or only one that suites you. Type 2 is with end wall. Made in FreeCad…
This is a stand for your headphones, and a fan at the same time. Form and function in one package. My headsetstandfan fitted with Noctua Airflow Amplifier. This uses a 120mm pc casefan. Cut the frame off, so that headsets fit better.…
Backplate uses a special 4mm Connector plate. If there is a need I could change it to a more comon speaker connector
I needed somewhere to put my phone to play music from while showering. Hook diameter is 7mm, and gap for the hook is 4mm, but it can be bent so wider bars can pass. Slot for the phone is 84mmx15mm, it should fit most phones. Print with…
Easily printable phone holder and amplifier in one Can customize the color combination you want. To assemble I use 10 3.5x15mm bolt. There is a small storage space at the back of the phone. The hole for the phone is 12x85mm.
It is a sound amplifier for mobile phones I made to listen to music. It is possible to use with 8,5 cm x 2 cm phones, so you do not have to remove your case or power bank. Printing in PLA with 2 walls, 2 layers top and bottom and 10% fill…
Simple phone holder with a little more sound. Printed with supports. 25.05.2025 I added a newer version 2.2 more stable and more louder!!
Simple mount for the XH-A232 amp, 4 wago 221's and a stereo jack to power the basshakers on my simrig.
Small passive amplifier for phones. use 20% infill and 3 wall lines for best result
A model of 70's punk icons amplifier head. Misfits DOYLE'S ORIGINAL custom STAGE-SHOW USED GUITAR AMP punk history DANZIG aka MDOcS/SUGApdD
I've designed this caase to mount for a 5mm infra red LED on my old amplifier. This LED emulates an IR remote control and makes my HiFi AV amplifier smart. (Followed this instructions…
Changed the fixation system to another clamping mechanism as the original model did not work out for me
Stand to help hold up Aiyima T8 Tube amplifier pre amp. This preamp was originally designed to sit inside the recess of the AIYIMA A08 PRO amplifier. I wanted to set it on top of my DIY Icepower amplifier and didnt want the preamp to…
It is preferable to print with support for better result.
Housing for DollaTek TPA3116 speaker amplifier with 2*50W speaker connection and 1*100W subwoofer connection. For assembly inert the five button in the respective holes. If available you can add spring beforehand. Use two plastic feet for…
designed for mytechvision 6 channel 5.1 amplifier. (this one https://www.flipkart.com/mytechvision-6-channel-5-1-amplifier-without-case-electronic-components-hobby-kit/p/itm9f4a9449d4299 ) no supports needed.
I made a nice Phone Amplifier Passive Speaker Bottom 204.29 x 165.83 x 35 mm Top 215.29 x 176.83 x 15 mm Horn 111.35 x 111.35 x 131 mm Phone Hole 80 x 15 mm
This is a wall mountable case for an Audio Amplifier bench test box I designed and built. Purpose It was an opportunity to experiment with different methods for printing text and multi filament testing on a single extruder machine (Sovol…
Just a simple replacement rotary knob for the Pioneer A-616 Mark Hi-Fi amplifier. Printed in PLA with 25% infill, 3 walls and 0.1 mm layer height. No Supports are needed because of the shoulders.
A casing for a amplifier board bought on aliexpress. The board: https://www.aliexpress.com/item/1005006221857312.html An image reference of the product is added to the images if the board is no longer sold. Note, one of the images of the…
I've made 2 of these but have been avoiding uploading these because the electronics will be beyond some people and I will not accept responsibility for damage caused by anyone building one. This amp follows the same design scheme as the…
This mechanism works as an asynchronous(it doesn't need any clock signal) mechanical amplifier for binary signals. It can be used in the same way as a non-inverting buffer (or an inverting one depending on the assembly). This should allow…
Print upside down and supports may be needed for version 2….210mm x 210mm x 152mm
Simple case for the Range Video RV-Splitter 4-way Composite Video Distribution Amplifier: https://www.rangevideo.com/products/rv-splitter-4-way-composite-video-distribution-amplifier Assembles using 4 m2.6 x 12mm screws. I also sell these…
Since the amp originally has normal light bulbs wired in series, it is proned to fail. You will need 4 of the LED Holders and plug them on the prongs. The holes for the LED pins need to be drilled with a 1mm drill. Be aware of the correct…
Like I said, I bought my Fender Mustang LT25 amp used and it had a cracked handle so I decided to challenge myself to try and recreate the OEM part as accurately as possible. The coolest part is that it needed zero modifications from…
Design inspired from Maxxbox (Asus). Supports Portrait and Landscape Orientation. Tested with Asus Zenfone Max Pro M1 and Mi A1. Won't mind adding support for larger phones if this thing gets enough response. Print Parameters Print with…
Smartphone stand amplifier - passive speaker stand in the form of a note. For printing, lay it on the side and it is print in place.
***PLEASE MAKE SURE YOU UNDERSTAND BASIC ELECTRICAL SAFETY BEFORE ATTEMPTING THIS BUILD, OR CONSULT A PROFESSIONAL*** I made an enclosure to house the amplifier board and power supply. It has 10 outputs on the back for the 7.3 channels on…
NV-AA1-09 Airflow Amplifier specified for NF-A9X14 92mm Fan, with a custom support and two fixing points with M3 screws
Print one of each and 4x Legs (no supports). Assemble the TDA7297 by fixing the knob bolt to the Base. You can use some super glue if you want it to be more stable, but not necessary. The sound is great, I recommend using traslucent…
Made a case for the amplifier board with control Aiyima HY-5201 TWS HY-5201
https://www.banggood.com/T220H-2_0-Channel-TPA3251-bluetooth-5_2-Digital-Stereo-Audio-Power-Amplifier-Board-220Wx2-p-2016217.html?rmmds=myorder&cur_warehouse=CN&ID=6290793
Print with tree supports along the openings for clean results. 4 or 5 walls to prevent infill. 0.2mm layer height. 0.4 Nozzle. Prints in ~1hr on Bambu A1 Mini set to 100mm/s max speed. Thx to incognito2pt for original design!
Description Hello everyone, were is a passive phone amplifier that I made. Simply put you phone in this slot in the box and it will make your speakers way louder. This is a fun and cost effective way to give your phone speaker a little…
A simple clip in wall mount for the Wuzhi ZK-1002M amplifier. Printed from ABS+, but PLA and other should work too. Printed without supports, the overhang is minimal.
Print details: Material: CC3D PETG Light Gold layer height: 0.20mm Supports: No Infill: 15% [English] My friend recently got hooked on woodworking and started making mobile phone stands with built-in natural sound amplifier. Last week, he…
It is a Chickenhead knob for the power control on the Boss Katana Gen 3 50 Guitar Amplifier Combo.
I print the one that is used with the SolidSuit with an adaptive layer height from 0.12 to 0.2mm to save approx. 2h (compared to a full 0.12mm layer height). I only print the stand for smartphone with RhinoShield SolidSuit because I never…
My first 3d printing project, not yet tested. Supports needed. Inspired by Marshall MS-2 speaker Designed as a Bluetooth speaker, Step file included. Enjoy
Printed on my Bambu Lab A1 with layer height 0.2*mm and standard settings (50% speed for peace of mind) NB. It's stretchable in y-direction for a more smooth inlet or if you don't have that much space or filament
Step 1 Buy https://vi.aliexpress.com/item/4000231020672.html Step 2 Buy four 3mm diameter 16-20 mm long self tapping wood screws with tapered head. European screws are the best. Tapered at 45 degree angle and you can buy them by the kilo.…
