Liczymy pasujące modele…
I created this set of color coding attachments for analog audio over lan cable units like Thomanns Cat Snake or Pronomics NetCore system (these both units are identical in mechanical and electrical perspective). The plate covering the…
Summary Customized attachments for the Wolfbox MF50 dust blower for individual areas of application (keyboard, notebook cooler, all types of filters, etc.) Print 0.16mm layer height 3 outer walls / perimeters 15% infill supports are…
The print comes in many parts that will need to be clipped together. Print settings - (Bambu P1S) Material - Body needs to be PETG because the center section should allow for some flexibilty. PLA wears too quickly. The button extenders…
Preface There are good HSW OpenSCAD customizers out there as well as libraries to generate attachments, some I collected in this collection . What I found lacking was the ability to generate attachments on a grid and the ability to…
A simple yet clean solution to store the multiple attachments you can use with a Dyson vacuum. Works for the small attachments up to the large mopping ones. Attaches to the wall with 2 screws. This mount allows you to snap in the…
**WARNING**: THIS IS VERY SHARP AT THE FRONT OF THE BARREL. KEEP ALL SENSITIVE BODY PARTS AWAY FROM IT. **NOTE** THIS IS FOR THE 12 BCAR VARIANT OF THE ZNC AUS. YOU WILL ALSO HAVE TO PAINT IT.(unless you have ams and set a color change)…
This is a vented threaded oil funnel for Toyota threads (37x3). I have designed a funnel, a cap, a regular funnel style attachment. I can confirm it works with the 2020 Toyota Tundra. I have made this out of PETG and ABS. Updated Model -…
Print with tree supports. The mount for the attachments is brittle, and blade may pull apart once broken free, just slide it back together.
Desk clamp able to support my line of modular attachments. Look on my page for the free attachments available! The clamp was tested with a cup holder with my wife's large water bottle full of water but strength will depend on printer…
Tired of slipping on ice? These simple 3D-printed spikes attach to your shoes with rubber bands for reliable traction on snow and ice. Proven durable after a week of daily use. Easy to install, only about 6 long rubberbands needed! There…
This model is compatible with the lego system.
Integrating Sphere Attachment (ISA). For measurements on integrating spheres with an opening of 70 mm. These ISAs were used on a Labsphere LMS-100 and utilize hollow sample holder geometry for reducing backscatter of photons into the…
A parallel arm with a heat press insert and thread tapping attachment. Maintains a right angle during installation. BOM Here Extrusion: 2020 x 150-200mm long (we used 155mm). Hole Pattern of Faceplate is two Rectangles, 30 x 60, and 20 x…
Simple pegboard mount to hold Shop Vac attachments. Quick and easy print. The attachments simply "click in". Very lightweight. Takes ~11 minutes to print. Feel free to make any modifications. Print Settings Layer Height: 0.16mm Infill:…
Uses standard MM3 collets (E3D heatsink collet)
holder for ORAL-B toothbrush attachments 3 stl-files for 2, 3 or 4 toothbrush attachments tips can be printed in different colors
(english below) Wandhalterung für Messkabel (BNC, Bananenstecker, Schuko-/Eurostecker, etc.) für Werkstatt und E-Labor mit Stauraum für Zubehör. Gedruckt werden kann das Modell aus verschiedenen festen Filamenten - ich habe PETG…
Hanger for IKEA nissafors cart. I used it for my car detailing cart. It works very well, you can hang it 90° or 2mm higher so it is at an angle so the water can drip on the floor and not on your cart. I used PLA because i had some on…
These parabolic reflectors allow for forward-facing beams. They are designed for the Mini-Bowern mount, which is used on LED light sources from Yongnuo and others. Several parabolic curvatures are available, as well as a protective cover…
A Barrett M82A1 inspired pocket bolt-action toy designed as a fun and functional fidget model. This model features a bolt-action mechanism , detachable magazine, and a compact design inspired by the iconic Barrett rifle. The model is…
This is a universal storage holder for Kenwood mixer attachments, designed to work with both older (spring-ring) and newer (bayonet-style) systems. Instead of copying the original locking mechanism, this design uses a flexible friction…
I was sick of my attachments falling off the mount for my vacuum. I designed a simple offset to give it a more secure fitting.
This is Thrustmaster T.Flight Hotas X for my office chair, easily adaptable for most chairs - just put some foam between chair_clamp_bdy1 and chair_clamp_bdy2 and scew it tight. The elements named right and left are simmetrical except for…
Wanted to add a few attachments to the magazine adapter. Required M3 Heat inserts and M3x10mm screws. Category: Hobby
I liked the idea of displaying my Printables badges on the HSW where I store my tools - but the original design (https://www.printables.com/model/219514-printables-badge-mount-for-honeycomb-storage-wall) didn't seem to fit the wall for…
Print the male2male long flat side down Print the female 2 female like a teardrop The long one can also be printed with flex or tpu to give that real wonky feel The grooves in each allow you to stick in a toy like a ribbon or a…
Custom modeled wall mount for the three attachments that come with the vacuum: the crevice tool, the dusting tool, and the upholstery brush. Mounted with adhesive strips, don't recommend. I need to redo with holes for screws, if you want…
This is a plate with 6 brackets for Dyson Air Wrap attachments. The base plate has a recess so that it fits under an IKEA "VARIERA" shelf - see pictures. Of course, it can also simply be used as a holder for Dyson Airwarp attachments. The…
Snowman fairy lights Everyone knows fairy lights and I thought they could be customized a bit. The idea came to me while I was about to print a lamp and see the competition. I have developed snowman attachments that you can easily put…
I made these attachments for my Shark Vertex Pro but should fit any vacuum with a 34mm attachment wand. I printed with PLA and it's held up pretty well. I printed them vertically, the bottom facing down and with supports.
My small belt/disk bench top sander has two ports for connecting a shop vacuum. Neither port is the correct size for the small hose on my shop vacuum so I designed and printed suitable hose attachments. At the same time I designed these…
A 1x3x7 Gridfinity container for the 3 hose attachments (3mm, 6mm, 8mm) for the Quick 957D
Clean larger surfaces more quickly with this friction fit wide end attachment for Wyze Vacuums. Two options: One mostly straight out angle and one curved. Slides directly on, no modifications. Put some organic supports under the last 2cm…
Phone Lanyard Card for attachments, so you can connect different cords to your mobile device. It relays on the fact that your mobile phone is in a case and you can put the tail through the USB-C port hole. There are 2 versions available…
V3 UPDATE 04-Nov-2023 - Created hygrometer mounting plate for simple set of sensors, removed adafruit sensor thing; updated spindle spinner to include spinning handle for each part; updated spindle holder; added blank spindle plug to fill…
Баліста (посилені кріплення тятиви) / Ballista (reinforced bowstring attachments)
Two-part accessory mount allows the Levoit LVAC-200 attachments to be mounted onboard the appliance itself for quick use, instead of stashed away in a fixed location. I've always found that I don't spend the time to go get the attachments…
Series of brackets for holding the hose and the extra head from your miele cannister vacuum in your closet
The philips pasta maker comes with 8 moulding attachments, but it's internal storage, stores just 5. And when you buy another moulding attachment you need to store them to.
I needed a #4 attachment. I used a parameter so the others were quick to add to the set. Recommend printing in PETG with supports. I used PCTG for the prototype because it was loaded and ready. Works great!
Organize your 3D printing workspace with this durable, high-quality set of two 3D filament spool holders, designed for maximum versatility and robustness. This set features a horizontal mount and a 90-degree underside table mount, both…
This model is perfect if you have a K1C and wanted to add detachable ducting to the exhaust fan with the original activated charcoal filter, or if you have a regular K1 and wanted to add both. This press fits into place on the back of the…
These models are meant to be used in conjunction with the magnetic filter holder mod I created here: Creality K1/K1C exhaust charcoal filter holder for magnetic attachments If you're a K1C owner and wanted to vent your chamber with…
Simply download the correct size adapter for your lens' filter thread. Made because lenses come in all sorts of shapes and sizes and I'm sure at least one other person needs another thread size to the originals included. I take no credit…
This is a 3d printed attachments holder for your pressure gun Design holds: - 6x nossels - foam cannon - Pressure Gun There is room for atachments that do not fit in the size holes and is designed to be fixed to the wall with two screws…
Extended by 25 mm and modified the geometry to have to a single material print with "teeth". For the rest please have a look at the original model. Print orientation Put it flat on the build plat like shown in the pictures. you only need…
Fits utility sink with 29-30 mm / ~1.156" rim. Mount is 3.0" long. Refer to my other models for attachments, including hanging bins. Compatible with Akro hanging bins, e.g. AkroBin 30210. More info at blog.outpost4.org.
Three additional attachments I couldn't find else were that I needed for the following items: 58mm paper filters 33mm spray bottle (originally from Amazon I think) Fellow soft-bristled brush (came with the Ode Gen2) Notes: Printed on a…
I created this set of color coding attachments for analog audio over lan cable units like Thomanns Cat Snake or Pronomics NetCore system (these both units are identical in mechanical and electrical perspective). The plate covering the…
This is a remix of the excellent Multiboard parametric files by sjcundy . Unfortunately, I don't know how to make the changes I made and keep the model parametric, but per request, I've uploaded the files here that I created using his…
The print comes in many parts that will need to be clipped together. When clipping on the main base hook the arm on the left side than push the part up until fully clipped and the underneath is mostly flush. For the LT and LB buttons the…
I measured the attachment point on my mixer and offset the shaft a little bit for an easy fit while the hangar is attached to the cabinet. I also set the thickness of the hooks "backbone" thin enough for my cabinets to close over them.…
Mounts for attachments for the 20L wet/dry Ryobi vacuum Printing in PLA and with 0.3mm layer height is fine. No supports required.
Tapered and Flat Nozzle Attachments for M18 FUEL Dual Battery Backpack Blower ( 3009 ), M18 FUEL Dual Battery Blower ( 2824 ), M18 FUEL Blower ( 3017 ), and the M18 FUEL QUIK-LOK Blower Attachment ( 49-16-2793 ). Also compatible with my…
Opzetstukken voor de festool-stofzuiger, zo kom je ook in de kleinere kieren. Attachments for the Festool vacuum cleaner, so you can also reach into smaller cracks. Groeten Ludo
Printed on Sovol SV08 PLA no supports standard settings If the tolerances are too tight on your printer, you can adjust them in attached CAD file.
Just posting a make from files on Github. The files are public domain. I wanted to see how accurate the Prusa app tool was. While the Prusa tool is ok (most the time). I wanted to be 100% sure I was the same on both sides. I used the…
This model holds all the attachments that come with the Shark FlexFusion air and ceramic styling system. It holds the brush, styling concentrator, two curlers, and the wet or dry fusion air straightener. I've changed the model from the…
First of all, many thanks to @cmh_13634 for the great model! After the first test, I noticed that water from the bottle dripped onto the fan. I didn't like that so much, which is why I decided to make one (ok, ultimately two) attachments.…
Use for any Synchronous Motor when you want to attach a 1/2in pvc pipe for props. When choosing a motor, make sure you get the one with the one "hole" (technical term). Once printed, you might need to sand or keep shoving the PVC in the…
Thanks to the original model creator for sharing this pedalboard design, I enjoyed building it and learned a ton in the process. I wanted to mount my power strip to the pedalboard and designed a set of power strip holders by leveraging…
A wall mounted attachment holder for Eureka RapidClean Pro Cordless Vacuum. Made specifically for the two attachments which come with model NEC280TL, which the manufacturer neglected to provide a suitable storage solution. The arms…
A hook to hold a Makita DUX18 (and likely others) powerhead unit by its battery guard, and wall mounts for storing the powerhead attachments. Includes 4 variants with different pin orientations. Simply slide the attachment into the mount,…
These 3D-printable accessories enable you to expand the functionality of the Husky Build-Out mobile toolbox system. The cleats and corners attach to the bottom of any flat surface, allowing you to securely lock custom work surfaces onto…
This is a remix of @PaulGrimes_855599 's tenting base for the Keychron Q11 split keyboard. This design is set up for Keychron's own wooden palm rest but it should work fine with many others too. Some problems I had with the original and…
This is simple box to store the attachments for the Bosch GSR 12V-35 FC drill. The box uses 3x6mm cylindrical magnets to hold top together There are 2 version simple one and additional with decorative rim which was created due to issues…
simple adapter from theragun to some cheap attachments from Amazon (Uk. Link: https://www.amazon.co.uk/dp/B0CG9FQG97?re)
Attachments for the 31,5 mm and 38,5 mm tubes of vacuum cleaner (small cone for installation). Support not needed.
I adjusted the original model to make it as stubby as possible. I also removed all unsupported overhangs around the latch area. I also made the latch easier to press by making it larger. I also made the tip the same diameter as the…
You can mount some cool stuff on it :) Check other uploads for iphone top camera mount! For better results, print in PETG. Might be a little bit tight! Screw Holes are M8 size, M6 will be good enough too.
Shark cordless vacuum is a great tool for every kitchen. The detachable battery makes it easy to charge separately from the bulky body. With all so many pieces it'd be easy to lose some or have them strewn throughout the house. This helps…
These accessories allow you to expand the functionality of the Husky Build-Out mobile toolbox system by adding custom attachments to the bottom of the toolbox. The cleats and corners securely mount to the underside, enabling you to attach…
This is a model of replacement brackets for a multi-implement rail made by Everbilt. There's a “rubber bit for large” which is to scale down the size of a large holder to hold small implements, and a “rubber bit for small” which fits the…
A pair of attachments for the XTools portable soldering iron that includes, tip storage, wire tip cleaner, and a spot for a Solder Sucker (I designed it for this model). It uses 19x2mm magnet disks to hold these in place.
This whole project started when I wanted to create a small rake for this RC tractor. I've never come around to actually building a rake but now I have a 3 point hitch with various attachments. Additionally I've also included a blank mount…
Bowden attachments for lawn mower with anti-pull-out lock PET-G Nozzle – HF 0.4 Layer - 0.2 Fill 15% Perimeters 5
The milk frother that I got for my wife didn't come with a stand. I have a 3D printer, so let's hammer this nail. ;-) In order to make the base heavy to avoid tipping, I printed the bottom part out of ProtoPasta Copper filled HTPLA…
I'm posting rails and attachments for my son's Cold Steel Big Bore blowgun. The first piece is a double-sided NATO Accessory Rail ( STANAG 4694 ). The rails were created using an OpenJSCAD port of the OpenSCAD code from…
These will connect to the top rail on a Graco Lauren Changing Table. Rail measurement 20mm x 30mm. Note: have to unscrew the rail to install. prevents failing off easy The Diaper holder can hold 6 diapers at single time. The small Basket…
A variety of different attachments that clip on to a standard whiteboard aluminium extrusion. Print in PLA or PETG if you expect it to sit in the sun. A couple can be printed without support but I would recommend printing on their side…
This allows connecting a 2.5" hose from a Vacmaster Pro shop vac to the LowRider 2. Includes both a Dewalt version and Makita version of the "VacShoeTop." (The original default "VacShoeTop.STL" should not be used, as the redesigned ones…
A print in place watering can with optional attachments. I printed mine in PETG but have included sliced files for PLA If you're slicing the STL yourself I recommend a 100% infill doesn't need supports to print. each end attachment is…
Simple Honeycomb holder for the Wolfbox MF100 and its its attachments.
This is a remake of the original Vortex Genie 2 Attachments by hisashin found on http://www.thingiverse.com/thing:3528209 . It will fit Eppi"s and 2 ml vials. Printed this and used it for the bead beating step in the DNeasy UltraClean…
This is a full remix of the excellent Dyson tool wall mount bracket by richieclarkie ( https://www.thingiverse.com/thing:4097193 ). I needed a stronger version because the brackets with screw holes had a 90-degree angle which was a weak…
Brought your chili can nerf barrel attachment to the game and want a drink? Have a nice cool soda! Made for both N-Strike and Rival barrel lugs! (They're printed upside down so you can shoot out the bottom of the cans.)
A back case for the CMF Phone 2 Pro by Nothing, which includes an M2 screwdriver compartment (as well as a printed screwdriver*), a 5-in ruler, and 13 hexagonal holes for different attachments. These holes and hexes have room for magnets…
I designed different attachments for Hexbugs Circuit Smash bots. The goal is to push each other out of the ring and with the additional attachments it is a lot of fun to do that. In the files you can also find "Dummyweapon.stp" which is a…
Made this to reduce side light from lamp as the light bulb is slightly poking out. There is two model variants: First one designed to be printed with transparent filament on the first layers to transmit light and the rest with non…
This is a highly versatile 3D printed survival multitool designed with modularity in mind. Perfect for camping, hiking, gardening, or emergency kits , it includes interchangeable heads such as shovel, pickaxe, hoe, compass cap, and more —…
Printed with Prusament PETG. No Support needed. All in One and without Tools to attach.
Over the last few years, the original attachments all broke in the same place, the small tab securing them to the clipper. I was not abel to source any replacement parts online, so modelled a set base on the original. They may fit others…
Introduction A simple pair of magnetic holders for attaching flat bellows to a metal lathe as ways covering. I used this 5/8" tall flat bellows available from McMaster Carr: https://www.mcmaster.com/1320K111/ These bellows are made for…
A stand for an electric whisk and it's attachments. Made using ‘Dallfoll Milk Frother LB-9023’ . I think this is a generic product that's often re-branded. You can measure the holes to see if yours fits. Features Cut out for a USB charger…
I took Sillybutt's Trion SCAR model, split it between the SCAR and the connector end, slapped the Little Rocket socket on the muzzle side, and the lugs on the SCAR side. There are two options for the muzzle connector: The original…
![Vacuum Attachments [Severin HV 7146] _Remix](https://media.printables.com/media/prints/1102126/images/8353343_b46cf285-5de2-4bd7-a6f3-d0db71c9d9f2_88c6be9a-e6b3-4798-9088-7ef92ea74112/resized_257.jpg)
