P
PrintablesJeremy Laurenson
BME280 HiLetgo 3.3V Atmospheric Pressure Sensor Cover
Created using Fusion 360
Wydruk około 0,33 €–0,41 € nettoWstępna wycena jednego wariantu
- Pobrania
- 148
- Polubienia
- 10
- Ocena
- 4,5
Wyniki wyszukiwania: bme280
Liczymy pasujące modele…
P
PrintablesLuckyJaS
BME280 & SHT20 holder
Holder for sensor GY-BME280 3.3V (humidity, temperature, barometric pressure). BME280 Link to my models 0,15 mm layer. Sensor mounting: Allen screw M3x6 or 8 Fixing the top cover (but not needed, the cover holds on its own): Allen screw…
- Pobrania
- 312
- Polubienia
- 37
- Ocena
- 5
P
PrintablesPHabermehl
fischertechnik BME280 I2C temperature sensor case
Ein fischertechnik-Gehäuse für das abgebildete Sensor-Board mit Bosch BME280 Temperatur/Druck/Luftfeuchtigkeitssensor. Montage durch Snap-in-Deckel, der auch die Platine in Position hält. Keine Schrauben. 4-adriges Flachbandkabel, direkt…
- Pobrania
- 109
- Polubienia
- 7
- Ocena
- 0
P
PrintablesM
ESP8266 + BME280 Enclosure w/ Quick Slide Mount/Base
ESP8266 + BME280 enclosure with quick-slide mounting base and printable board lock for a tool free installation (not including a screw or two for the enclosure mount). I flipped the ESP8266 board inside the enclosure so the chips were…
- Pobrania
- 72
- Polubienia
- 8
- Ocena
- 0
P
Printables
Meshtastic DIDDY "ULTRA" GPS + BME280 upgrade kit REMIX
UPFRONT! I created a Discord channel for my Thermal vision builds but will add a #meshtastic channel there as well in case you have questions or problems. Please remain to the meshtastic channel for all sort of questions as all the other…
P
Printables
Case for the Waveshare BME280 sensor
Case designed for the Waveshare BME280 breakout board. Keeps your sensor protected while allowing airflow for environmental readings. It was designed to be mounted on 2020 extrusions. BOM: 2× M2×4mm screws (sensor board mounting) 1×…
P
Printables
Heltec Wifi LoRa 32 Cases (v3/v4) with environmental sensor (BME280)
This is a collection of cases for the Heltec WiFi LoRa 32 v3/v4 boards. It holds the board, a battery, and optionally an environmental sensor. The button (PRG) can be pressed and the reset button (RST) is accessible via a pinhole (use a…
P
Printables
Meshtastic DIDDY "ULTRA" GPS + BME280 upgrade kit REMIX
UPFRONT! I created a Discord channel for my Thermal vision builds but will add a #meshtastic channel there as well in case you have questions or problems. Please remain to the meshtastic channel for all sort of questions as all the other…
P
Printables
Bme280 housing
house for a bme280 sensor uses m2.5 screw to hold sensor in place, but it is not needed..as the jumper plugs hold strong
P
Printables
BlueDot BME280+TSL2591 sensor case
Just a simple case with a snap-in lid for the BlueDot BME280+TSL2591 . I also added the blend-file if you want to modify it for your use case.
P
Printables
ESP32 Weather Station (BME280, SPS30)
Remixed the housing from JT https://www.thingiverse.com/thing:2820147 in order to support: ESP32 Feather Huzzah with 2.4" TFT Wing Bosch BME280 sensor Sensirion SPS30 sensor Source code can be found here:…
P
Printables
Home Assistant weather sensor (S2-MINI + BME280)
-ESP32 S2 mini -BME280: Cheap, small and accurate enough sensor for pressure, humidity, and temperature sensing -Small wood screw (OD: 4mm, Length: ~8mm)
P
Printables
ESP32 Dev (USB-C) with BME280 Sensor Enclosure
This enclosure is an original, custom-designed case for the ESP32 Dev MCU board (USB-C), with space in the lid to securely house a BME280 sensor for temperature, humidity, and pressure measurements. The design ensures the ESP32 board is…
P
Printables
LACK BME280 sensor mount for Ender 3
This is another sensor mount for my Ender 3. See here for my previous one: https://www.thingiverse.com/thing:4597337 I made another one, because i was not satisfied with the laginess of the AM2302/DHT22 on the RaspberryPi. This mount…
P
Printables
Case for Wemos D1 Mini and BME280
Compact case for Wemos D1 mini and BME280 sensor with an entry hole for a cable entry grommet. Many thanks to the creator of the original model: Big Dog Custom Creations . In addition to the .stl files, step files have also been added for…
P
Printables
nomadBox - heltec WiFi LoRa 32(V3) case, GPS, BME280, buzzer, rotary encoder
Case for Heltec WiFi LoRa 32 V3 This case is designed for the Heltec WiFi LoRa 32 V3 and includes the following components: Included Components: GPS Module (NEO-6M or GT-U7) On/Off Switch (S3P = SRS3P, 19.4 x 5.6 x 5mm) → Link GY-BME280…
P
Printables
Octoprint monitor weather station esp8266 D1 mini ssd1306 bme280 case
Octoprint monitor weather station esp8266 D1 mini bme280 case What a mouthful. It shows the diversity for which this can be used for. Usecases: Octoprint monitor Weather station InfluxDB querry NTP clock Desktop widget Whats needed: Wemos…
P
Printables
BME280 BMP180 Si7021 sensor cover
Cover for BME280/BMP180/Si7021 sensors, with labels of pinout Category: Electronics
P
Printables
Temperature and Humidity Sensor - Powered by ESP32-C3 Mini and BME280
Temperature and Humidity Sensor Release v2.0 Project Features This project is a compact temperature and humidity monitor built with an ESP32-C3, a BME280 sensor, and a 1.3-inch SH1106 OLED display. It's designed for simplicity, low power…
P
Printables
(Wemos) D1 Mini + BME280 Temp Humidity Sensor Case
A simple case for a (Wemos) D1 Mini + BME280/BMP280 + Battery Holder / Battery Pack. There is a cutout for a rocker switch which is highly recommended (when using batteries) as you dont want the batteries connected when using the usb port…
P
Printables
ESP8266 Multi Sensor BME280 (battery powerd) - T, Humidity and hPa, incl. Code
I started my Home Assistant instalation a few day ago and now added these sensors to it (will make a window reed contact next on the same base). The ESP ist running on the ESPhome software (you can find a good guide in how to wire up the…
P
Printables
40mm fan cover + BME280 mount
Mesh used is 0.2mm thick PET plastic mesh harvested from reusable Billa fruit bags. Flange for the fan is sort of delicate and supports can be hard to remove from there.
P
Printables
Case for Meshtastic board DIY v1.05 with BME680(BME280) and 1.3’’ screen by EugeneS
PCB there: https://github.com/NanoVHF/Meshtastic-DIY/tree/main/PCB/ESP-32-devkit_EBYTE-E22 Schematics there: https://github.com/NanoVHF/Meshtastic-DIY/blob/main/Schematics/E-Byte_E22/Mesh_Ebyte_E22-XXXM30S.pdf Button 6x6x9.3 Screw M2 for…
P
Printables
BME280 Breakout Sensor Gehäuse 16mm Pole
I like using the Wemos D1 ESP8266 microcontroller together with ESPHome to integrate sensors into my Home Assistant setup. For this project, I wanted a way to attach a BME280 temperature and humidity sensor breakout board to a 16 mm tent…
P
Printables
Case for Electrocookie 1/4 Stripboard, ESP32/ESP8266 and BME280
I needed a small, compact box to hold a 1/4 Electrocookie Stripboard (my favourite) with an ESPHome controlled esp8266 and BME280. The box has two lugs to allow for fixing to a wall using screws. The sensor needed to remote from the…
P
Printables
BME280 Temperature Humidity sensor mounts
BME280 Temperature/Humidity sensor mounts. The holes for attaching the sensor to the mount are intended to accept M3 heat set screw inserts. The holes for attaching the mount to something else or intended for M3 wood screws. There are…
P
Printables
BME280 Case
A tiny case to slide in the BME280 sensor. Designed to be friction-fit and used with soldered pins. Print it standing upright.
P
Printables
Case for the Waveshare BME280 sensor
Case designed for the Waveshare BME280 breakout board. Keeps your sensor protected while allowing airflow for environmental readings. It was designed to be mounted on 2020 extrusions. BOM: 2× M2×4mm screws (sensor board mounting) 1×…
P
Printables
Heltec Wifi LoRa 32 Cases (v3/v4) with environmental sensor (BME280)
This is a collection of cases for the Heltec WiFi LoRa 32 v3/v4 boards. It holds the board, a battery, and optionally an environmental sensor. The button (PRG) can be pressed and the reset button (RST) is accessible via a pinhole (use a…
P
Printables
BME280 mount for Radiation Shield
BMP085 mount for "Radiation Shield For Weather Station Temperature/Humidity" by micromet. For the rest of the radiation shield follow this link: https://www.thingiverse.com/thing:1067700 Print Settings Rafts: No Supports: No Resolution:…
P
Printables
BME280 Chain mount
Simple solution to get a place for the BME280 temperature humidity sensor. You need: Heat insert 3x5x4 Short M3 screw Zip tie
P
Printables
Jumper Plug Housing for Raspberry Pi and BME280 Temperature, Humidity, Barometric Pressure Weather Sensor
Friction-fit enclosures for jumper wires for connecting a Raspberry Pi to a BME280 weather sensor module.
P
Printables
D1 Mini Bme280-sensor sphere
This is a small enclosure for a D1 mini+batteryshield+bme280 sensor for homeautomation. Used components: D1 Mini NodeMcu mit ESP8266-12F WLAN Module für Arduino Batterie Shield für Lithium Batterien für D1 Mini GY-BME280 Barometrischer…
P
Printables
ESP32 D1 Mini BME280 IoT sensor case
This is a small case that snugly fits an AZ-Delivery ESP32 D1 Mini board. The lid is designed to mount an external BME280 or BMP280 sensor board, although this is optional. It has been designed and printed as part of this project:…
P
Printables
BME280 Enclosure
This is a small enclosure for a BME280 temperature and humidity sensor. Print instructions Printer: Prusa Mini Supports: not needed Layer height: 0.2 mm Infill: 15% Filament: Prusament Vanilla White
P
Printables
sensor housing for BME280 and IMU-9225
This is a sensor housing for indoor use. The outside dimensions are L x W x H: 90mm x 70mm x 43,5mm. The wall thickness is 5 mm. You need: 4 M3 thread-inserts to complete this build. 4 M3 x 12 (or less) ISO 4762
P
Printables
BME280 Mount for 2020 extrusion
I needed a simple mount for a BME280 breakout board on a 2020 extrusion. BOM: -) 2020 T-Nut -) M3x8 or M3x10
P
Printables
Waveshare BME280 Holder
A simple Holder for the Waveshare BME280 Sensor. The hole is for an M3 screw. I used it to mount the sensor in an Voron V0.1 as chamber temperature sensor. For reference this is the bm280 i used: https://amzn.eu/6RERB8z V2 is a simpler to…
P
Printables
ESP8622+BMP/BME280 BOX
This is a box for ESP8266 30pin+BME280 temp, humidity and pressure sensor. Easy to assembly, just slize in the lid.
P
Printables
Bme280 housing
Uses m2.5 screw to secure the sensor in the housing…but its not needed, as the jumper wires hold rather snug. in the pictures, im not using a screw. made using freecad
P
Printables
BME280 extrusion mount for Voron 2.4 and Voron 0
BME280 is a temperature sensor, it also gives humidity and pressure. I use it as chamber temperature sensor in my Voron 2.4. There is several form factor, be careful to have the one on picture to use this mount ( eg.…
P
Printables
wemos d1 mini bme280 housing
housing for wemos d1 mini with space for male pinheader and bme280 top part no support needed simply print top and bottom separately
P
Printables
BME280 mount for 2020 extrusion
Simple mount for a BME 280 temperature/humidity sensor to a 2020 extrusion. Used it to mount the sensor to the gantry of my Voron 2.4. Check the photo if your sensor has the same PCB. You need 3 M3 screws and 1 M3 T-Nut.
P
Printables
BMP280 BME280 V Slot Sensor Housing
…Please be sure to hit like & post a make, I'd love to see your prints! Install your BMP/BME280 sensor on any V-slot. Or use base with no mount for glue on application. Measure temperature, pressure & humidity on your Rpi. You'll need: 1x…
P
Printables
Ikea Lack C270 + BME280 mount for Prusa enclosure
You can mount your Logitech C270 and BME280 sensor together!
P
Printables
PMS5003 / DHT22 (or BME280) / ESP32S Air Quality Sensor case
This custom-designed enclosure is tailored to house the Plantower PMS5003 Air Quality Sensor, along with an ESP32 NodeMCU and a DHT22 (or BME280 when using the alternative lid included in the files) temperature and humidity sensor…
P
Printables
BME280 + BMP180 outdoor cover
Small cover for BME280 and BMP180. For outside use, PETG/ABS/ASA is preferred. Recommended settings: 4 perimeters 0% infill
P
Printables
Temperature & Humidity Monitor with BME280, Wemos D1R2 ESP8266 and LCD1604
Temperature and Humidity Monitor for my Prusa Mini+ enclosure, although it is standalone device (requires USB input for power) so can be used anywhere you want to monitor temperature, humidity and barometric air pressure. A small,…
P
Printables
Sensirion SPS30 / Adafruit BME280 Weatherproof Outdoor Enclosure
This enclosure was built to house a Sensirion SPS30 (particulate matter sensor) and an Adafruit BME280 (temperature, humidity and barometric pressure sensor) for an outdoor weather station. The goal was to have an enclosure that could be…
P
Printables
BME280 Breakout Module Model
This is a simple dimensional model of the common BME280 breakout board. Accurate enough for modelling - not to spec.
P
Printables
Compact Case for use with the WEMOS D1 Mini and a BME280 Temp and Humidity Sensor.
Compact Case for use with the D1 Mini and a BME280 Temperature, Humidity, and Pressure Sensor. I designed this and use it for reading temperature and humidity in various locations around the house. I use that information for Home…
P
Printables
Housing for BME280 / SHT3X sensor - with magnetic base & hook
Housing for a BME/BMP280 sensor (5V edition) or a SHT3X sensor. Can be screwed down with a M3x6 screw.The base can hold a 8x3mm magnet. Print instructions Category: 3D Printing Summary Housing for a BME/BMP280 sensor (5V edition) or a…
P
Printables
MoleBox: barometric pressure, humidity, temperature - BME280
MoleBox system - 3D printed boxes compatible with BITBEAM construction kit (therefore even with LEGO Technics/Mindstorms). The main purpose of MoleBox is covering a particular sensor or the entire module and simultaneously allowing…
P
Printables
BME280 Holder for IKEA VINDRIKTNING
This model helps you mount a BME280 to the backside of an Ikea VINDRIKTNING . This model requires support and I'd recommend printing it with the big pillars facing downwards. But be careful when removing the supports!
P
Printables
NodeMCU + BME280 Case
This case requires two pieces of hardware. One is the NodeMCU with built-in display that I used here. The other is the BME280 sensor that can be picked up from here. 3x m2x8 screws and inserts for putting together. I have also attached…
P
Printables
(old v1) ESP32 + BME280 weather station with stevenson screen
Version 2 is available now! Outdoor Weather Station based on ESP32 and BME 280 Little outdoor weather station with ESP32 (NodeMCU and similars) box which can be mounted to a rail or similar (clamp diameter 22mm). It has an arm to hold the…
P
Printables
ESP32 Box and lid + vented + outdoor version, for BME280
Box and lid for ESP32 modules (NodeMCU boards and similars). The BME280 version offers a mount point for the sensor below the main board. Also, the box then has vents. However, testing revealed that the board gets so warm that the sensor…
P
Printables
ESP8266 + BME280 enclosure
Design a simple enclosure for my ESP8266 + BME280 temperature, humidity and pressure sensor with micro USB space for pow
P
Printables
Presence sensor ESP8266, LD2410C, BME280 and WS2812 Status Led
Presence sensor for use in Home Automation Parts used: ESP12E (ESP8266) with breakout board, 26x38mm HLK2410c 24G radar sensor, 22x16mm. BME280 Temp, pressure and humidity sensor, 15x12mm WS2812 LED, x4 pixels, 10x32mm. Notes: All parts…
P
Printables
BME280 Sensor Case
BMP280 / BME280 Sensor Case with strain relief for 2-8mm diameter Cables You need 2x M3x10 DIN912 Screws This is a composite Part, click on “Split to Parts” in PrusaSlicer and right click on the intended elements. Add the following Part…
P
Printables
BME280 SHT31 SHT30 SHT3x housing with strain relief
Liked the original and modified it a little
P
Printables
BME280 ESP8266 Battery case
Close case for BME280 wifi station base on battery (no cable) more safe in high humidity area.