Liczymy pasujące modele…
Just replacing another missing piece : ) Print Settings Printer Brand: Anycubic Printer: Photon Rafts: No Supports: Yes Resolution: 0.12mm Infill: 100 Filament: Anycubic UV resin your choice Category: Other
Replacement Handrail stanchions for an Aristo-Craft RS-3 locomotive. Also fits the Aristo-Craft center cab and Lil Critter. Added a "Heavy duty" version 3 May '21
!!!can carry 90 kilograms!!! clear surface under support material. Under arches, where were supports it is very coarse. i recommend to refine with sand paper. Maded in Autodesk Maya and Zbrush. Tymyn_3D Print instructions Happy printing
Friend of mine builds railings for offices and homes. Mostly in stainless steel. A post, a mounted cylinder with Ø12mm pin. Stainless tube on top and weld it. Now the purchased jig was worn out and he needed replacement. As the…
Note: Header photo shows the provided version on the bottom left, a previous version (not published) is in the top right. Requirements You first need to make sure this pot fits your balcony handrail: Distance between bars: 105mm Size of…
I added pic rail to the other end of the handrail so I could move my bipod down the barrel farther.
I intend to at some point reverse engineer the entire cars to upload onto these websites so all of you can create your own and make them more accessible, as we currently only have a baggage car, combine car, and coach car that is reused…
Tabletop: Print as is. Handrail: Printed on its side with supports for the rail mount. STL and STP files included of the cradle if you want to create your own version, or just combine it with the Stanford Bunny.
Printed in PETG this is very strong. I have been using these for 2 years with full kids backpacks and none have broken yet. I did go through several until I got the design correct to spread the weight.
remixed to have a full pic handrail
Made this for a friend's balcony handrail. Fits the original mounting adapter surprisingly well. Required hardware: 2x - 4x M3 countersink screws 2x zipties (optional) 2x - 4x M3 threaded inserts (optional) Best printed out of PETG. I…
I wanted to install a handrail and I did not like the commercial off the shelf products we get in my country. I wanted to use a Chromes Aluminum pipe of 38mm (1.5inch) diameter which I could obtain at low cost, but the mountings I could…
Use petg. Its a snap on fit. Use 3 threaded inserts M3 https://www.3djake.at/3djake/gewindeeinsaetze-50er-set?sai=9419
The original sideboards & handrails are often broken off by the time you find one of these Tyco Maintenance Wagons for sale on ebay or at a train show. I've carefully modeled replacements based on the appearance of the single original…
Boat Ø25mm handrail cup holder attached with L35mm M6 bolts. I recommend to use A4 quality. Dimensions made for standard 0,5l beer can as in picture.
Hello. This is a jig that bends wires into handle shapes for use in scale modelling. I got inspiration from such existing jigs, but mine is 2 in 1, where you can create 3mm and 5mm wide handles, with a lot of handle heights to choose…
Required Screws 🛠 I don't quite remember what screws I've used but: Clamping the Pipe: Probably M6x14 screw, cylindrical head with a hex socket (Allen key compatible). For Wall Mounting: Probably Ericsson M8 screw. Printing…
In our pool, the safety tarp with zipper is hooked into the handrail. Unfortunately, it falls out again easily when the tarp is not hooked in or you want to close the zipper. The clips keeps the tarp in the handrail and you can close it…
The handle for the cabinet door that it doesn't have it. Designed for doors thick 18.3 mm. Use a double-sided adhesive tape to attach to the door. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution:…
I don't know if this will be of any use to anyone but I'll publish it here just in case
Mount stuff on the handrails. For 25 mm/ 1 inch pipe (print the correct version). A cup holder is included, so you can see how it is used. Choose cup holder for vertical or horizontal mounting. You could also integrate the inner part…
It is connector for handrails for stairs. Pipes have 40 mm diameters. Old one broke during fixing stairs and of course haven't time to mount new one :(, but is already printed :). I made it in PETG.
Handrail for garden house door
Few weeks ago I had my car in autoshop and repairman broke my ceiling handles. He bought and put in new ones and gave me back broken parts. Turned out the only broken thing was little pin holding the spring. In photo it is that green…
37.5 Degree Stair Baluster Connectors for Square Balusters No Drilling Fast Installation for Deck Handrail Staircase Balusters Comparable to : https://amzn.to/3XDFyZs Compatible with : https://amzn.to/429OveB
FLAT Baluster Connectors for Square Balusters No Drilling Fast Installation for Deck Handrail Staircase Balusters Comparable to : https://amzn.to/3XDFyZs Compatible with : https://amzn.to/429OveB
A round end cap for a specific European aluminum handrail (as seen in image) that goes on top of glass railings. I made the model for work since I'm running short on aluminum end caps and can be replaced for indoor railings in some…
Boat handrail pipe Ø25mm cup holder attached with L35mm M6 bolts. I recommend to use A4 quality. Dimensions made for standard 0,5l beer can as in picture.
Ein Halter für den größeren Gardena micro drip Schlauch am Balkongelaender. A Mount for the bigger gardena micro drip tube. I used ASA, because I use them on the balcony, UV! Print Settings Printer Brand: Prusa Printer: I3 MK3S Supports:…
A laundry rack (or better: rod) for mounting on a wooden handrail. The rod is of wood, and the mounts are 3D printed, with a clamp and big plastic screws to fasten this without damaging the handrail. My wife requested this to dry landry…
I needed a simple hook to hang something on my deck's railing. I found the model uploaded by Johncarter to be close to what I needed, but it didn't fit the shape of my angled handrail. I modified his original model in Tinkercad to better…
Replacement handrail stanchion assembly for Lionel Trains MPC-era GP-20 locomotive Print Settings Printer: Sindoh 3Dwox Rafts: Yes Supports: Yes Resolution: 0.2 layer height Infill: N/A Notes: This .STL is set to FINE quality. Because…
A more stable handrail for the RC Boot. Print-in-place. Settings Value Infill 15% (adaptive cubic) Perimeters 2 Solid Layers Top: 6 ; Bottom: 5 (default) Layer Height 0.15 mm Structural Material PETG Supporting Material only overhangs /…
Handrail clamp. I used it for vertical handrail - pipe with 40 mm diameter. Square “hands” are for 50 mm wooden bar. PETG recommended.
This is a mechanism for longtail bike Décathlon ELOPS R500 handails. This allows you to raise one of the rails so kids can easily climb in, while ensuring they remain securely enclosed during the ride. Assembly requires M3 and M5 screws.…
Mount plate for brackets where the part that goes into the handrail is not affixed to the bracket, but screwed on.
This adapter is made for this model . It slides into the pre-existing slot and keeps the feeder steady on the handrail. My handrail dimensions are 40mm wide by 11mm tall. No supports are needed.
This part is a handrail stop for blind people. It's designed in two half peaces and will be assembled with two Ø3mm x 15mm timber screws. It is possible to align the two half with M8 hex nuts. Inner diameter Ø45mm Category: Household…
Made to hold down garlands onto a wooden porch handrail or posts. Version 1 is just a prototype that worked for my use. Version 2 is reworked 2mm wider to fit a little looser, has 3mm fillets on all angles except the bump that is supposed…
Rokenbok handrail custom sizes. Prints best laying flat (as shown in photo) I plan on adding more variants in the future.
Handrail bracket I designed to replace a broken handrail bracket. I tried to buy a bracket at the local Blue Big Box hardware store on Easter but they were closed. So, I designed my own. Works great. Print it sideways so it will be very…
This is a very basic part. In my home there is a staircase using old 30x30 square steel tubes as posts. As you can see the handrail is mounted inside the concrete floor and without the cover it looks quite ugly. Look at the images for…
Wall handrail support for metal flat bar
Ich habe hier ein Wandkonsole zum Stirnseitigen befestigen eines Handlaufes aus Holz mit einem Durchmesser von 40mm erstellt. Die Bohrung des Handlaufes läuft konisch zu und wird nach hinten hin enger (vorne Ø40,2mm, hinten Ø40,1mm). Ggf.…
Boat rod holder to D25mm handrail and for four rods
This is a jig designed to help with redrilling the holes for the handrails on a Hornby J15. The Hornby model has the handrail knobs fitted horizontally whereas the prototype had the knobs running perpendicular to the boiler. The knobs can…
EN: Model for old buses. I think this model could be useful for some people, so happy printing. Made to be 3D printable. I recommend using something stronger, like ASA . CZ: Model pro staré autobusy a trolejbusy. Tehle model by mohl podle…
Couldn't find a wooden rounded corner and did not want a sharp corner so printed one in PLA and painted.
Крепление поручня К-002 автобусов (кронштейн, кронштейн, разъем) @В зимний период из-за реагентов гниет держатель для поручня в пассажирском автобусе Ford Transit Fastening of handrail K-002 buses (bracket, bracket, connector) In winter,…
Ich habe hier ein Endkappe für einen Handlauf aus Holz mit einem Durchmesser von 40mm erstellt. Die Bohrung des Handlaufes hat einen Durchmesser von 40,1mm. Ggf. muss etwas mit Schleifpapier (am Handlauf) nachgeholfen werden. Das drucken…
This is a square end cap for specific square shaped aluminum handrails (pictured) that go on top of glass panel railings. Made as spare parts for work. Maybe it's of help to someone out there.
This is a handrail clip / holder for a square handrail 40 x 40 mm. It can be used to hold e.g. a light chain. Printing 3 perimeters 20% infill The clips were printed in PETG Galaxy Black. The “5x” files contain 5 clips for print. Change…
Side connector for stairs and custom Baluster Connectors for Square Balusters No Drilling Fast Installation for Deck Handrail Staircase Balusters Similar use to : https://amzn.to/3XDFyZs (although this type of connector does not seem to…
The goal was simple. Adjust my cpe wifi antenna (tenda o3) on balcony rails and aim it in the right direction. It works so I'm pasting my project with photos here. ofc it's not the only one application for this shit. If you want to hang…
This is a safety-focused end cap specifically designed for 1" galvanized handrail pipes (33.7mm outer diameter)
cap for old handrails about 1970 mainly used in italy
Handrail repair part +80% infill 4 walls supports enabled Rotate 90deg so it lays as shown on screenshot
I needed some method of hanging ropelights around my patio handrail that was easy to take on and off and would be durable. I printed these in white ABS to withstand the winter sub-40°C and +40°C summer temps that we get in Saskatchewan,…
Ochrana rohů madel / Handrail corner protection
Upper pool handrail (eight-form pool) This specially designed top pool handrail is the ideal solution for eight-form pools to clamp the pool liner safely and cleanly. The profile has been designed to reliably fix the liner without…
This set of supports was designed to create a rope handrail and includes: Wall-mounted pass-through bracket Rope end cap The design was created for a 30 mm nominal diameter jute rope . The rope opening has intentionally been designed with…
The original sideboards & handrails are often broken off by the time you find one of these Tyco Maintenance Wagons for sale on ebay or at a train show. I've carefully modeled replacements based on the appearance of the single original…
Rokenbok handrail custom sizes. Prints best laying flat (as shown in photo) I plan on adding more variants in the future.
This is a safety-focused end cap specifically designed for 1" galvanized handrail pipes (33.7mm outer diameter)
Mount stuff on the handrails. For 25 mm/ 1 inch pipe (print the correct version). A cup holder is included, so you can see how it is used. Choose cup holder for vertical or horizontal mounting. You could also integrate the inner part…
Handrail bracket I designed to replace a broken handrail bracket. I tried to buy a bracket at the local Blue Big Box hardware store on Easter but they were closed. So, I designed my own. Works great. Print it sideways so it will be very…
Boat handrail pipe Ø25mm cup holder attached with L35mm M6 bolts. I recommend to use A4 quality. Dimensions made for standard 0,5l beer can as in picture.
I designed Handrails with a Diameter of 1.3mm. You need to Check if it fits your locomotive, if not, just use the Fusion file to make it fit.
