Liczymy pasujące modele…
This is a gear bucket system for the 8" round hatches found on Hobie kayaks and boats. There are various tray configurations and sizes to organize your tackle / gear / accessories. The bucket will print on a 25cm x 20cm build plate (Prusa…
Best to print in PETG, ASA, or something similar for outdoor use.
If a padeye on your kayak breaks or is lost then this is can be a useful replacement. In addition to the printed part you will need an eye bolt to screw into the center hole; I used ¼" with 20 threads per inch in this design since that is…
These files were used to create a scale model of a Hobie 14 catamaran. The file titles should be self-explanatory for the most part. The hulls are cut in half lengthwise in order to print flat on the bed. The top and bottom should be…
Protects the seam and bottom of the kayak from the ground when loading and unloading. Uses the original bolts that come with the smaller skid plates.
Three of these cleats are on the Hobie 16 mast: the jib and main halyard are riveted; the downhaul is attached to the luff groove with special square nuts. Parts required to install as a halyard cleat: - 2x 3/16x5/8" 6-10 stainless steel…
Wall mounted oar holder for the hobie carbon fibre kayake paddles. I've found it fits some other paddles too. I printed on the side, no supports needed
A tool, in two parts, for unscrewing a broken Padeye from a Hobie kayak. It also works to remove and replace an un-broken padeye, of course. This is my first design and will probably be useful to no-one but myself.
This adapter allows you to plug and play your Garmin Striker plus 4 transducer to the Lowrance Ready bay on your Hobie Kayak. I cut up pieces from Yakfisher's design here to adapt to the cheaper transducer than comes with the Striker plus…
Normally I'd post a link to the stream where I designed this part, but unfortunately I didn't stream this one, so all you get is this link to my channel where I design things like this: https://www.youtube.com/c/ClarkSchaefer/videos .…
poulie de drisse de grand voile sur un hobie wild cat. l'épesseur de la pièce est a reverifier en fonction du mat du bateau.
goosneck bearing for hobie 14/ hobie 16 boom, it's worse than the original bearing but printed in pet still doesn't create too much friction, if you need a quick replacement that works. I drew it by eye because I didn't have an original…
These nuts were used in Hobie 16s and 14s until the mid-1980s. They were replaced by stainless steel nylocks (part #8050310), but still work pretty well. This design uses ANSI #5/16-18 threads. After printing, I ran the nut up and down a…
Cleat for the kayaks, a bit on the larger side, but I also wanted to be able to pick up the kayak with it. Printed with supports, but upside-down produced the least amount of supports/cleanup. Heavy perimeters, and if interested, a coat…
Designed this for my old Hobie Cat 16 Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: Doesn't Matter Supports: No Resolution: 0.15mm Infill: 100% Filament: Prusa PET-G Prusa Orange Category: Sport & Outdoors
The original design was a four rod holder but the rod tubes were too close together. I designed this to fit three rods with more space between. This is meant to be held down with the lower rear seat rail of the Hobie Lynx seat. It may fit…
These parts are used along with a nut, a bolt, and a spring to connect a Hobie 16 rudder tiller to the crossbar. Each tiller connector requires 1 large washer and 2 domes. The washers are concave on one face to improve fit-- it doesn't…
Chariot pour un hobie cat 14. Il faut démonter les poutres du catamaran pour l'insérer dan le raille.
This adapter installs by removing the clevis pins attached to the jib furler and the hardware that comes with the Davis Telo-Cat. Allows for the Telo-Cat to be easily removed when not in use.
Garmin Striker 4 plus Hobie Through Eye Wiring Hole Mount Simply undo the through hole wiring grommet, replace with this - feed the cables up thorugh the holes in the adapter, add some silicon or other sealant to keep the water out, and…
This is the gooseneck bearing for a Hobie 16 Catamaran. It needs a stainless 3 inch screw to connect the top and bottom. Allows for easier downhaul adjustment, prevents the boom from getting hung up in the mast track, and protects the…
Hello fellow Printers this is a replacement tube for the Hobie Livewell. V1 I made it a little longer so it all ways pokes into the scupper hole. Printed on Bambu X1C .4mm Nozzle .16 optimal preset Thanks
This design is a fish finder mount on a Hobbie iTrek 11 or Mirage i11s ( old name) it's design to for a Garmin STRIKER 5cv but can work with any Garmin fish finder GT20-TM For other fish finder, you just need to design a different…
Mount your GoPro on the front of your Hobie 16, 14 or other beach cat with a chain plate bridle that does not have a furling jib. You can find the GoPro hardware here: https://a.co/d/gv4sAux The screws I used to attach to the bridle are…
Hobie Pad Eye Screw Mount Railblaza Starport Mashup Category: Sport & Outdoors
This is a model I hacked at in tinkercad to allow a Garmin Striker Plus 4 transducer to mount to the hull of my Hobie Pro Angler 14. The model allows for four 8x3mm N52 magnets to be glued in, allowing the transducer to stay securely in…
I designed this block so that a piece of 80/20 extruded aluminum can be placed on the two blocks and using 2 inch U-bolts it can be bolted to the block. This provides access to the t-rails to mount any attachments you desire.
This is designed to provide a snag free way to keep a hobie tiller extension from sliding off the tiller bar when on the beach or handling the boat. Version 1: the next revision needs to be rounded and angled to match the angle that the…
My original foot straps were always a bit too small for my size 13 dogs. When one finally rotted and broke, I made a replacement strap. File may be mirrored with the slicer to accommodate either side. Print with TPU.
Decided to repurpose one of my spare h-rail mounts to secure my anchor spool. Its designed to mimic this generic YakAttack adapter I had lying around. Also had to print a thumbnut since the original was missing, the printed one requires a…
Good to at least 50G shock with a 200g GoPro (100N), use at your own risk. Printing with 6 walls and 6 bottom layers, 8 top layers with ABS. Hardware: 3x M5x20 CSK 3x M5x20 washers
These parts are used in the lower rudder castings on the Hobie 16 to adjust rudder tension. They are designed to replace the original acetal screws and plungers. The factory adjustment screws require an unusually wide flathead…
decided to make a spindle base mount to attach a wind indicator onto the top of my Hobie tandem island adventure. should slide in real snug. used a metal chopstick i had laying around in the cabinet,chopstick had a .265" base, hot glue…
Remixed the pad eye by PopDukez into a cleat, specifically in my case for the bungee cord at the back of my 2014 Hobie Outback. 100% infill for strength. Haven't put it through it's paces yet, but might need to reprint in PETG for…
These housings are threaded to accept standard Hobie 16/14 drain plugs. I prefer mounting them on the boat with a polyurethane adhesive sealant (such as 3M 5200) instead of silicone. I recommend printing the housings face-up, with…
Hobie recommends storing the Hobie 16 with drain plugs removed to ventilate the hulls. Unfortunately, I learned that field mice can fit through the drain holes (and will happily chew up the buoyancy foam inside). This drain plug has a…
Good to at least 50G shock with a 200g GoPro (100N), use at your own risk. Printing with 6 walls and 6 bottom layers, 8 top layers with ABS. Hardware: 3x M5x20 CSK 3x M5x20 washers
A friend of mine has a real old Hobie Cat sailboat with an all Aluminum mast. After many years of use, the masthead pulley (Nylon with a brass insert) just fell apart from weather & use. Since Hobie no longer makes or supplies this part,…
The handles of my kayak broke off so I designed new ones. I added an inset of the Hobie logo to press fit inside the lid. Use glue on the logo if you like. The logo parts have already been reduced in size to fit inside the lid. Hobie…
This is a replacement rudder cam for many of the Hobie catamaran fleet. They are 10 dollars a piece and are made out of a low grade practice. Decided to test and print my own. These will also be available on Etsy. ASA, PETG, or ABS being…
This is a sheave for the single-sheave masthead castings used on old Hobie 16s. Hobie no longer sells this part. My design has a slightly deeper groove profile than the original, with more durable flanges. It should be less prone to…
