Liczymy pasujące modele…
Junction box with space for a Dayton reversable drum switch on top. 2 holes in the box for standard ¾" knockout wire clamps. Cover holes are clearance/tap size for #8 machine screws. switch mounting holes are for #10 countersunk screws.
This versatile remix includes two base options and three cover sizes, providing flexibility to fit multiple junction box configurations. The bases are compatible with all covers, ensuring easy customization. However, the large base…
I needed a junction box to hold a small 5V PSU-Board as well as a Relais-PCB within an REV-Ritter cable duct. Here is an qick model for that. It can be fixated wihin the duct with the two T-Screws. I left some space on the bottom of the…
Fully customizable wall top / in wall box for whatever you need. When mains are inside and most of materials are flammable, use it in / on non flammable wall and surrounding. Typically concrete basement far from wood etc. Or choose non…
I have an inline bathroom exhaust fan, but needed to connect it to three vents without running back to the store. Glue and fit the panels. A blanking plate model is included if you don't need all four.
Introducing the Radial Energy junction box system. An universal and ever growing junction box system for your custom electronic needs. The first core component of this system is the base. An universal round enclosure with 8 cable entries…
Junction box for 2 WAGO 221-413-1 terminals. Cable strain relief via zip-ties. 4mm holes for wall mounting. Created from scratch, inspired by https://www.printables.com/model/774882-wago-221-2x3-thin-junctionbox
Multiconfiguration WAGO Junction Box V2 – Waterproof and pole mountable This is the next-generation version of the original Multiconfiguration WAGO Junction Box – now upgraded with robust new features to meet real-world demands. Check…
Electrical safety warning: Messing with electrics is dangerous and kills. Please don't attempt to use this junction box if you are not familiar with electric safety procedures and regulations in force in your country. Your safety is not…
UPDATED: VERSION 2 - WAGO connectors now snap in place without moving (thanks to @pulsar ). - Lid screws are now not exposed but hidden in the lid. - Added support for WAGO 221-613 Design This Hexagonal design is meant to help with cable…
Electrical safety warning: Messing with electrics is dangerous and kills. Please don't attempt to use this junction box if you are not familiar with electric safety procedures and regulations in force in your country. Your safety is not…
Surface-mounted box model for light switches, thermostats, and similar electrical accessories
Model Description Flat, 3-way junction box for Wago 221 series wire clamps. This model is heavily inspired by a design shared by https://www.printables.com/@geroulas . This version features a more rigid hold on the Wago clamps by using a…
HILOOK Camera Junction Box This model is a custom junction box / mounting base designed for HILOOK dome cameras (tested with IPC-T241H-C). It allows safe and clean installation by hiding connectors and cables inside the box while keeping…
HILOOK Bullet Camera Junction Box This model is a custom junction box / mounting base designed for HILOOK bullet cameras (tested with IPC-B141H-C). It allows a clean and professional installation by hiding all connectors and excess cable…
Posted only the back mount, the rest is the same as the original. All credit goes to the original designer, I just needed to move the mount to the side so it would fit next to the Stealthmax. Printed in standard Voron settings, follow the…
This is a replacement plug for the Commercial Electric brand of junction box covers that keeps out rain and bugs. They're not sold separately, so it's a real drag when you lose one. Printed in ASA for outdoor / UV protection.
A junction box with perfect fit for a switch, 3x Wago 221-413 clamps and a fit for Shelly 1PM Mini Gen4. Keeps al the components stiff at its place. Two cable wholes for power inpunt and output. Use case : Connect you 3D printer to your…
I used OpenAI Codex to build a mounting plate in SCAD for a Wehooper4 SolarXiao and 2x2 4P 1S 21700 battery pack that fits in a 7.4" x 4.7" LeMotech Aluminum Junction Box. The mounting holes for the SolarXiao board were taken from an…
This insert is specifically for the WaveShare Solar Power Manager (14500 battery) and the XIAO nRF52840 & Wio-SX1252 Kit to be used with the 150mm x 100mm x 70mm junction box. To my surprise the 14500 battery does very well in combination…
I changed this model to accept an M3 heat set threaded insert instead of a hex nut. They can be installed from either side of the hole. I chose to install the inserts from the underside of the hole to help prevent it being pulled out.…
Connector with 22x1 mm thread for electrical junction boxes
This is the grand Junction Temple front view. I took the measurements and got a accurate view of the temple. The problem was the steeple was to tall and skinny. so i change some of the dimensions to create a more usable cookie cutter.
This is a mount adapter for an IP67 junction box to attach to a pole, mast, or anything round-ish using hose clamps or stove pipe straps. Remixed from this excellent model by @quantenquark . The use case would most commonly be for a…
Works for these furring strip boards: https://www.homedepot.com/p/1-in-x-2-in-x-8-ft-Furring-Strip-Board-160954/100009348 Part of a set of connectors I designed to eventually make a rigid cage to keep the birds off the strawberries. They…
Posture Corrector Yoga Cross Stick - Muscle Release Tool - Yoga Sticks - Stretching Tool - Giunzione Barre correttore Posturale Yoga Sticks Technical Specifications: Default Stick Diameter: 21mm Customizable: Easily resize/scale the 3D…
This is a remix of the excellent model by @BobdeBouwer_481949 . Credits go to him! I moved into a house with ceiling junction boxes for smoke detectors, but I had already invested in battery-powered Nest Protect V2s. I looked everywhere…
Electrical safety warning: Messing with electrics is dangerous and kills. Please don't attempt to use this junction box if you are not familiar with electric safety procedures and regulations in force in your country. Your safety is not…
Electrical safety warning: Messing with electrics is dangerous and kills. Please don't attempt to use this junction box if you are not familiar with electric safety procedures and regulations in force in your country. Your safety is not…
Built to replace hard to get conduit junction box connectors. In PL these are only found in specialist shops and these also can be a bit expensive. This design uses nylon ziptie as a compression, to provide very tight fitting. For now I…
A cover for a junction boxe to be used to lock in place a tplink rapo C500 cam (or any cam with those holes). the project is open source, the freecad file is downloadble. Cap width: 132 mm Cap height: 108 mm Box hole width: 80 mm Box hole…
Remix of @Riskable's outdoor electrical box, half inch conduit holes, with the addition of thin knock-out partitions. Please follow all instructions in the original model.
In Line Wago 221 Junction Box, perfect for splitting 1 wire to 2 wires. Compact design
Summary While doing a small wiring job I realized that connections would be exposed, I didn't bother with making some conduit I just made these very small junction boxes. Two patterns are supplied , a 40mm long box, and a 60mm long box…
This T Piece junction will accomodate a 100mm ID PVC pipe. It is designed to be used in conjunction with my other design of a 90 degree elbow and fit 100mm ID PVC pipe and/or a 100mm flexible hose. The other design is here:…
Scalable Electrical Junction Box Extensions for Device and Ceiling Box All models are 12mm - Scale Z dimension to any length you need Print with high wall loops (6x+ for 0.4mm)
I am using some white PVC trunking to tidy some wires, and I wanted a junction box which could fit the following trunking: Deta TTE uPVC White Self-Adhesive Mini Trunking 25mm x 16mm x 2m The junction box accommodates Wago 221-613…
I am using some white PVC trunking to tidy some wires, and I wanted a junction box which could fit the following trunking: Deta TTE uPVC White Self-Adhesive Mini Trunking 25mm x 16mm x 2m The junction box is designed to hold a RF433…
Moisture plug for junction boxes, it's used to avoid the creation of moisture inside the box due to temperature changes. I've designed it some time ago, the bolt is not sized correctly, you'll need a 17 metric wrench but it's not a…
Replacement electrical cover for the BOSCH Cooktop HT6ET60 (PKN675DB1A). I printed this with PETG and so far it seems fine. The junction box does not appear to get hot when the cook-top is operation. If anyone can suggest a better…
Junction box used: https://www.amazon.com/gp/product/B09DD6RQV3/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1 ( 5.9 x 3.9 x 2.8inch ) Magnets used: https://www.amazon.com/gp/product/B09MLHSL4P/ Uses m4* 8* 6 heat thread inserts for the…
The enclosure is a simple and customizable design able to hide and provide protection for cable junctions. It is easy to print without support and is configurable to handle multiple cable entry points and configurations. The clam shell…
Víčko na instalační krabičku s prodlouženým dzinzikem
Junction box with space for a Dayton reversable drum switch on top. 2 holes in the box for standard ¾" knockout wire clamps. Cover holes are clearance/tap size for #8 machine screws. switch mounting holes are for #10 countersunk screws.
Small surface mount box, for hiding cables and wago connectors - just shorter Please use low-current sensor and signal wires only . It is not suitable for mains wiring due to potential safety risks and regulatory non-compliance.…
Needed a wall box for new (used) camera avigilon 2.0-h3-d which needed some protection for the inline connectors and the original ones are very expensive and in short supply. Using a photo of the rubber seal plate I created the base, you…
07 This is an adaptator to fit 40mm diameter pvc pipe to 80mm rain water pipe with a 2° slope for water drainage purposes. I used it to connect an outdoor sink drain to the roof rain gutter pipe of our house. Printing: Any setup works,…
Simple box for 2pc of Plejd. You need to adjust the holders a little on the underside with a file. Printed in PLA with 0.20 layers
Printed with 0.15mm layers otherwise at least the thread of cover isn't ptinted properly. After designing and mounting I've realized, that screwing the cover onto the box isn't really nice. I could snap it on with breaking a few pieces of…
Small surface mount box, for hiding cables and wago connectors. Choose caps for the required cable size. If you’re looking for a junction box with more space and features take a look at junction-box-different-sizes by 3Dimensions…
Note: The Ethernet Module PINs didnt land where I expected based on the model, so I used a knife to cut the lower two standoffs. I attempted to replicate this in the .STEP but its not tested and certainly would be below the expected…
A simple and compact junction box, without the cable clutter. Can be resized to fit different terminal block sizes. Note: There is no pull restrain, use at your own risk!
I want to make my lighting smart, and the switches should still work, but there wasn't enough space in the cable outlets to accommodate the additional smart actuators. I was inspired by two models from printables and i created a cover…
Needed to design a custom Junction Box for a Hikvision dome camera DS-2CD2145FWD-I(s). Came up with a simple design of a Junction box with a threaded inner side and a corresponding mounting plate for the camera with an outer thread.…
Assisting tool for marking 1 to 5 junction boxes on walls, to help you easily align the drilled holes. It is made for the European-standard type, marking a centre-to-centre distance of 71mm and a hole diameter of 82mm inner and 85mm outer…
Unifi G5 camera - junction box inspirováno originální krabičkou pro vnitřní použití tisk z PETG 2x zatavovací vložky 3x10x5 pro M3 šroub 2x M3x20 šroub Unifi G5 camera - junction box inspired by the original box for internal use print…
I printed my one using white ASA material using .3 mm layers in draft mode. If you care about precision and less visible lines, surely it is possible to print using more precise settings. Printing time in my case was over 3 hours.
Made this model to adapt Tado X Thermostats to the 503 junction box. This model uses additional parts : 2x M3 screws 2x M3 threaded inserts (6mm diameter, 5mm lenght)
This versatile remix includes two base options and three cover sizes, providing flexibility to fit multiple junction box configurations. The bases are compatible with all covers, ensuring easy customization. However, the large base…
My usecase was a lamp hanging form the floor through a junction box, so I wanted to plaster the hole. But from each common junction box cap the plaster dropped off. So I designed my own cap holding the plaster.
This remix of the junction box cover features an engraved symbol indicating a motion sensor substitution. It retains compatibility with all original bases and cover sizes (80mm, 115mm, 150mm). Perfect for installations where visual…
Junction box measuring 160x120x80 with lid. The box is pre-drilled to run cables.
This is hole plug for Hikvision cameras junction box like DS-1280ZJ. You can use it to close openings on your junction box. You can print it without supports, better to use 4 wall loops and 40 - 60% infill. I recommend printing from PETG.…
Junctionbox cover (Abzweigdosen Deckel) to mount a Vallox MV C 80 on top.
This innovative junction box is fully compatible with the WAGO 221 series and supports all connector models, including the 221-412, 221-413, and 221-415. Designed for maximum flexibility, the rail-based approach allows you to mix and…
This innovative junction box is fully compatible with the WAGO 221 series and supports all connector models, including the 221-412, 221-413, and 221-415. Designed for maximum flexibility, the rail-based approach allows you to mix and…
Simply said, original from paw patrol tent joint was weak for kids :) So created robust one. Easy to print. Dimensions: rods diameter 1,1 cm total height: 8,5 cm width: 5,7 cm / 5,7 cm Print instructions: see 3mf file PETG easy print
Simple strap to mount electrical junction box on wire fence (but may have other uses).
I needed a junction box to hold a small 5V PSU-Board as well as a Relais-PCB within an REV-Ritter cable duct. Here is an qick model for that. It can be fixated wihin the duct with the two T-Screws. I left some space on the bottom of the…
Blank wall cover plate Check out my app: app Dimensions: - "Small" diameter: 70mm - "Big" diameter: 110mm - Depth: 12 mm More from me: https://roqd.one Follow me on social media: https://www.youtube.com/@ro_qd…
Single-Screw Junction Box with Removable Cover Hide a small wire connection in a compact wall box that opens quickly without removing extra cover screws. Check out my app: link Small connections are often easy to hide but frustrating to…
I live in an old building in New York City, where my electrical boxes use a metal spacer bracket that interferes with wide-body smart switches. This bracket provides more lateral room for switches at the same spacing, and an optional…
Deutsch: Ich habe einen Baldachin, auch bekannt als Deckenrosette, für Lampen entworfen. Der Baldachin hat ein einfaches Design, besitzt einen Durchmesser von 10cm und eine Höhe von 3cm. Er passt perfekt zu allen Lampenstilen und schafft…
Small junction box to contain the cables behind an access control exit button from Aliexpress (wall-mounted) The exit button can be mounted to the holder with the included two screws.
This is still a work in progress. I have not yet tested the cover in a real installation. If you use this, please post a picture of your installation as a “make”. Allows a Reolink Video Doorbell PoE to be mounted over a single gang…
I bought the product below from aliexpress Brand Name DIY GO Model Number 221 This is a cheap wire connector I made it simply because I didn't have a junction box that fits exactly. My printing conditions Printer: ender V3 SE…
Coperchio per scatole di derivazione 130 mmx 110mm Junction box covers 130mm x 110 mm FILE STL SENZA SCRITTA
UTP/FTP Rubber Grommet Weather Seal for outdoor Security Camera / Junction Box The cut is thinner than the standard nozzle diameter, so you may need to use a cutter after the print is done. Use flex filament. Tested on a Hikvision…
While installing a lamp in the storage room of our house to make it easier to find things here, I noticed that the cover of one electrical junction box was missing. Hence a junction box without cover is quite dangerous, I simply designed…
MiloSplit Description Gather all your electrical signals at the back and merge them into one single Harking-like connector to form an umbilical between your Milo and the electrical cabinet. Endstops, toolsetter, touchprobe, coolant all go…
Small profile function box to secure 3 level wire connectors, designed to fit 3 ideal industries lever wire connectors. Please note that this is definitely not water tight so if being used outside I would recommend filling it with some…
This is a terrain tile that features a junction of one pipeline with another for 6mm wargames that will allow you to combine multiple tiles to make a gameboard. This is intended to be combined with other pipeline tiles to make longer…
This is mountable (4 through holes in the rear face) junction box designed to securely hold a standard 8-gang relay module with 4 screws (picture was taken before the module was secured but the screw holes line up perfectly), complete…
Junction Box PLUS - Full Set A modular junction box set made for your next project. After months of development in close cooperation with certifiers and professionals from the industry, we are proud to finally release these beauties.…
Large, electric box. Should be preferably printed from flame retardant material. Uses M4 heat-sinks and metrical screws. Designed for M20 electric glands. 3D printed glands are added to the model, however these require the cables to be…
Junction Box PLUS - 20mm - Set A modular junction box set made for your next project. After months of development in close cooperation with certifiers and professionals from the industry, we are proud to finally release these beauties.…
This model is a remake of Wallmount for Lenovo Tab M10 3rd Gen from Josef Rypáček. I added the compatibility for italian electrical junction boxes (503 type), added some holes on the left side of the model to be able to press power and…
If you find my work useful you can: paypal.me: https://www.paypal.com/paypalme/printyourfix Visit my website for contact form: https://printyourfix.com/ Follow me on Instagram: https://www.instagram.com/printyourfix/ Visit YT channel:…
![Wago 221 Junction Box for flex wire 3 core, 4 core or 5 core [compact]](https://media.printables.com/media/prints/785036/images/6155619_7f611648-fcbe-4d7b-8a40-1e9c82a991ab_a116373d-3766-4495-8e82-8ec115aa0a7e/pxl_20240304_202509674_scale.jpg)
