Liczymy pasujące modele…
I realised that people like to try a new hobby while staying at home. However, this usually means they need the tools and materials for it, delivered to their homes. As these products are not considered as necessities many companies are…
I'm not a fan of cluttered handlebars - this mount uses one of the headlight mounting bolts to keep the controller for Oxford heated grips up by the display on the 2023 Tenere 700. I'm not sure if this will work with earlier year models -…
… using the 4x original oxford screws and 2x M5 inbus screws for mounting on the handlebar. I scanned the handlebar with my phone and modelled the mount around it. I printed the parts in Fiberlogy PA CF12.
This model has different radius on the curve to fit the stock tenere bars snugly. You can slide it to make it tighter. I have used it for sometime now and it's staying in place without ziptie. I also added version with ziptie hole but I…
Mounts for the Zumo XT (and maybe others?) and Oxford's heated grips for the AdventureSpec Mini Fairing. There's a pocket where an Airtag can be snapped into on the rear of the GPS mount. Mounts to the fairing face using existing holes in…
I don't run perch mirrors on my Husqvarna 701 so I added a small bolt to hold this in place. You can just install it between your mirror and perch if need be. I printed mine in ABS and vapour smoothed it with acetone so it's nearly…
Printed in PETG, 80% infill and 0.2 mm layerheight. Super strong, and should have no problems holding the little oxford controller in place
yellow until 6.8mm finish with blue
Not a coincidence at all that the thick/thin distibution follows the golden ratio, for each 8 thick rhombi print 5 thin rhombi…advice, just enjoy tiling it, don't try to understand it :) Use the ultra high resolution tiling map…
An alternate mount for the clunky Oxford control box.
Key shaft sleeve to stop the sharp edges scratching paintwork Printed in TPU. Flat face to bed, no supports required.
A simple key sleeve for the Oxford Alpha AX14 Alarmed disc lock. To stop the sharp key shaft scratching paintwork. Made from TPU flex. Prints with the flat along the tail on the bed. No supports required
This is an alternate controller mount for the Oxford Heaterz Heated Grips Temp Controller. The included mount did not work well on the KTM Adventure 390 handlebar. This mount should also work on any handlebar with a 22mm diameter. It was…
Attach your Oxford heated grips controller next to your dashboard using a simple cable tie. 2 Versions: CRF300L - Oxford Heated Grips Mount (original) Ver 1.0 Compatible with the EUR (2021-2024) model CRF300L - Oxford Heated Grips Mount…
30mm hole spacing, but I included the F3D file so you can modify to your needs but this is the same hole spacing thats on the metal bracket the grips come with. Designed for CRF300L, may need slight tweaking for other bikes.
I needed something to keep the metal lid closed. This is still a WIP.
A very slim support for the remote/controller of Oxford heated grips/handle bars for motorcycle, ATV, snowmobile etc. Fastened with 2 zip-ties. Printed and fitted perfectly on my Husquarna (KTM) Svartpilen 401 (2023); its tight and you…
The Oxford Heated Grip Controller ships with a metal bracket that uses the mounting screws for the clutch lever, and then sits above it and angled backward. This intersects the stock mirrors on a lot of bikes, so I made my own adapter…
You'll need: handlebars which have a diameter of 22 mm. 4 tapered screws (should also be provided in the package with the heated grips) 2 M5 allen screws, 16 mm long 2 M5 Lock nuts.
Required: 2x M6 nuts (you will probably have to press them into place with a soldering iron). You can use the supplied stock bolts with Grips (M6x27) or install M6x30 to your taste. It is recommended to use Loctite to fix the threaded…
Ducati Hypermotard 1100 Evo indicator adapters for any 8mm indicators. This will allow you to move to cheaper and more extensive range of mirrors for your Ducati. Once you move away from the limited integrated indicator and mirror…
Update: Due to popular demand (an astonishing number of 0 downloads), I have updated the file in case you don't have the alu inserts available. Now there's a widened version with no pre-drilling required, and a version for an M4 nut.…
My motorcycle didn't have the mounts that Oxford heated grips were designed for. This is for 22 mm handlebars. For 21 mm you can use tape to pad it. Or modify the original FreeCad files I've included. Mounted with M6 screws 50 mm long and…
A mount for the older Oxford Screamer disc lock. It might work with the newer models but not tested, designed for a 7mm locking pin with around 70~mm length on the jaw. The mount side is for a 14mm tube subframe or similar, using 7mm wide…
3D printable topographic miniature of Oxford - 🇬🇧 United Kingdom Capture the beauty of Oxford 's city landscape with this topographic miniature! This 3D model represents the geographic area around the geo coordinates 51.753, -1.258…
Key shaft sleeve to stop the sharp edges scratching paintwork Printed in TPU. Flat face to bed, no supports required.
A simple key sleeve for the Oxford Alpha AX14 Alarmed disc lock. To stop the sharp key shaft scratching paintwork. Made from TPU flex. Prints with the flat along the tail on the bed. No supports required
Step into the grandeur of Renaissance nobility with this exquisitely detailed 3D printable figurine that captures the elegant essence of aristocratic fashion. This stunning STL model showcases period-accurate clothing including an ornate…
Oxford Heat Controller Mount Here is a simple yet really strong mount for mounting Oxford intelligent heat controllers. My metal clamp included didn't fit, and I found other solutions to be crude or look poorly made. So I decided to…
I have these heated grips on my bike, but the mounting plate they come with is garbage and doesn't attach on most bikes i've installed the grips in. I made a 22mm bar adapter that works pretty great. Maybe it will work for your bike too.…
The 1:76 scale Oxford Diecast cars come with a nice display case. Re-use the case for a small diorama with this street. The plastic casing snap on this print. The empty spaces are for Manhole covers and water access plates, which are…
Credit to raingel on thingiverse, this is just a straight share of his model https://www.thingiverse.com/thing:6230608 Based on recent findings from Oxford Nanopore ( https://community.nanoporetech.com/posts/flow-cell-light-shield ),…
The Honda NC750X DCT has a parking brake on the left handlebar and a nonstandard mirror mount, so the stock Oxford Hotgrips controller mount will not fit on the bike in that location. Certain work-arounds common to owners of that bike are…
Oxford Hot Grips are great, but the mount supplied with them is crap. This one mounts to a 31.8mm handlebar with a zip tie. The Oxford heated grip controller is screwed to the mount. Pics show it installed between the bar clamps of my…
It position controller as much to grip as possible. Cavity and additional holes is for water escape. Maybe overkill but... Requires rubber/silicone band. I've printed one from TPU. Screws: M5x20
