59 modeli
Update der Display Aufnahme für Bigtreetech btt pi tft50 v.2.1 Das Original Display Halterung ist unter https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/alanho/BTT_PITFT50_v2_Mount zu finden. Der Original Halter für den…
TFT 5" holder for Voron BTT 2.0 TFT50 this is a remix of ryanwilson's TFT holder. I raised the edge a bit to close the gap in the frame. After printing just break away the bridging bar. For printing please use the original instructions.…
This is a simple enclosure for the BigTreeTech PiTFT50 V2.0 screen assembly with a Raspberry Pi 4B mounted inside. The BTT mounts into the case with holes for the screw bosses and is secured from the back side with small metric screws…
Remix of PITFT50 Mount for the BTT PITFT50 HDMI by CannedBass https://github.com/VoronDesign/VoronUsers/tree/master/printer_mods/CannedBass/PITFT50_45_degree_mount BOM: 4x M3 Brass Inserts 4x M3x8 FHCS 2x M3 Hammer(T)-Nuts 2x M3x8 SHCS
45-degree mount for BTT PiTFT50 display to also work with the Clicky-Clack door modification intended for Voron 2.4. Display holder was found here: TFT 5" holder for Voron 2.4 - BTT PITFT50 by Alego | Download free STL model |…
After changing my Ender 3 S1 using Klipper, I also had to change the Stock-Display, because it became unusable. For the BTT PITFT50 Screen Mount , found at: https://www.thingiverse.com/thing:4800945 , I created a holder to change the…
Simple ventilated case. I use without radiators, with a fan for blowing inside, connected to 3.3v (not to 5 volts) - this is enough to cool and it is very quiet. In a room of 26 degrees C, the pi sensor shows 38-40 degrees C. Required:…
I couldn't find exactly what I wanted so I designed it myself. And I must tell you that it is very beautiful! I made a thin, sleek, minimal and sturdy vertical PITFT50 V2 display mount for the Ender 3 S1 and S1 Pro without the Raspberry…
What was originally supposed to be a quick modification of an existing case turned into a few hours long new design from scratch with improvements! The case was designed with the following goals: printable with minimal supports only use…
Currently untested, will update post or model when fully tested. Designed primarily for my Rat Rig Vcore 3 printers, but would work for any 3030 extrusion. BOM: BTT PiTFT50 v2 Touchscreen M3 x 8 screws - x4 M3 Brass Inserts - x4 M2.5 x 6…
I needed a case to fit the BigTreeTech PiTFT50 v 2.1. There are several cases out there for prior versions of the screen, but I couldn't find one to fit the latest version that I liked. There are a couple of key differences in v2.1 versus…
Very minimum mount for attaching a BigTree Tech PITFT50 V2 to a 2020 extrusion. Angle adjustable, default is 55 degree. It has room for a attaching pi in the back. My main goal for a mount is to still be able to adjust the brightness…
I wanted a case that fitted the BTT PiTFT50 and the Pi but none of the others out there filled my needs. I designed a basic right angle mount which I will be attaching to the front of my desk. Uses Go Pro style connections and I have…
Symmetrical modification of the BIGTREETECH pttft50 screen holder. Upgrade to a model created by ROBY. Note, the distance between the holder and the stand connecting 2 elements has changed. The holder is suitable for screwing directly to…
Modified screen cover for the BTT PITFT50 V2.1 screen which has three buttons in a slightly different position and size on the bottom of the screen to adjust brightness compared to V2.0 which used a thumb wheel. To be used with the…
updated Jan13: rev 3 should be safe to print and test. I printed rev 2 for the raspberry pi 3 and tft50 v2.0, and only one tiny fix was needed which is fixed in rev3 updated Jan12: there was a small area that needed shaving also tweaked…
This mount will fit a BIGTREETECH PITFT50 V2.0 5" Pi display. There are two files, a front and a back. Once printed, it requires 4 10mm countersunk type screws to attach. There is an optional wedge piece that can be printed to angle the…
Cathodic TV-style case for BTT PITFT50 V2.1 screen + RPI4 + fan This was designed so i don't buy anything else than what i had on hand, you will find a recap of what's needed down below. The main concern when designing this was airflow :…
A while back I converted my Qidi X-Pro over to a Lerdge K and it worked great for quite some time. It wasn't perfect but it was a nice configurable upgrade that made some really nice prints. Recently when making a klicky style probe for…
Bigtreetech PITFT50 display base for TwoTrees Sapphire Plus V2. Place 4 M3 metal inserts to fix the cover with the screen to the base. To fix it to the printer, it can be done by drilling 3 holes to use M4 screws or use double-sided tape.
This is a remix of the incredible BigTreeTech TFT70, TFT35, SKR, Raspberry Pi Case by max_davis (Thing ID 4568324) that I have adapted to my own setup. The case includes space for an SKR 1.4Turbo, a Raspberry Pi with a buck converter for…
Raspberry pi + PiTFT50 screen mount on the Anycubic Kobra Go. It attaches to 4040 extrusion. Printed it using 3 perimeters, 0.2 resolution and 15% gyroid fill.
Modified original case to fit the BTT PITFT50.
BigtreeTech PITFT50 DSI LCD Mount for RatRig V-Core 3030 Frame or any 3030 Frame. Use remaining parts from original model. You will need all printed parts and this nut and screws: 4x M2.5x10mm or 4x M2.5x8mm cap head screws 4x M3x8mm cap…
i used the V2 Mount with the outter most holes, and the spacer to mount my BTT TFT50 inside the screen case from this design: https://www.printables.com/model/445961-btt-pitft50-screen-case-mount-for-v-slot-ender as the original authors…
I wanted to have a nice wall-mounted case for raspberry pi 4 and BTT PiTFT50 screen that would include everything in one package. Print out the parts, assemble, and hang them on the wall! When printing the only thing you have to flip is…
I wanted a better mount for the PITFT50 display that I was using with OctoDash. This includes both the monitor case and the Z-axis frame mount.
This is BTT PITFT50 tabletop screen case that I remixed for my friend. It holds the screen with screwed-on Raspberry Pi. You have to use supports to print it.
I designed the enclosure and brackets to install the BTT PITFT50 screen on my V Minion. Worked out great for me.
Printed with ABS using the default Voron recommendations. I only uploaded one side. You need to duplicate the part and mirror it to have both sides! Print in the same orientation as on the cover photo.
A very rough mod for PiTFT50 V2 to the Anycubic Vyper, it uses the bracket from the original screen for the left or right side of the printer (the left side is under a different angle and is mounted on the top side of the bottom extrusion…
I installed a btt pitft50 onto my voron v2 using alanho's mount and wanted to free up some space in my electronics bay by mounting the pi on the rear of the screen. This mount raises the pi allowing it to clear the screens mount and…
Adapts https://www.printables.com/model/282522-pi-tft50-mount to accept https://www.printables.com/model/273885-mks-pi-ts35-box
Das Original ( https://www.thingiverse.com/thing:5881751 ) hat vorgesehen, dass der Pi an der Rückseite des Displays befestigt wird. Ich wollte das Display innerhalb des Gehäuses für meinen Neptune 3 Plus haben, aber den Pi außerhalb.…
I modified the screen back file to incorporate magnets. I had them laying around but I believe they’re 8x3 neodymium and I did a pause at layer height to insert them. The main body of the case can be downloaded from the vzbot GitHub…
Added 1mm more space for the display thickness Added buttons Customized back plate
This is an adapter/arm for using Sapencils great PITFT50 Shroud with standard 3030 aluminium extrusions. Two 10mm M5 screws with t-nuts are required for mounting. I just uploaded the newly designed mount (both as STL and FreeCAD .fcstd),…
BTT PiTFT50 + Raspberry Pi 4 2U 10" Rack Mount I couldn't find a model that matched my needs — a clean way to mount a BTT PiTFT50 - 5" display and a Raspberry Pi 4 together in a 2U — so I designed my own. I started with a standard 2U…
This is an adapter/arm for using Sapencils great PITFT50 Shroud with standard 3030 aluminium extrusions. Two 10mm M5 screws with t-nuts are required for mounting. I just uploaded the newly designed mount (both as STL and FreeCAD .fcstd),…
Printed with ABS using the default Voron recommendations. I only uploaded one side. You need to duplicate the part and mirror it to have both sides! Print in the same orientation as on the cover photo.
BOM: 8x M2.5*8 FHCS https://aliexpress.ru/item/4001199728978.html 4x Standard M2 Heat Set Inserts (M2x3.6x4) https://aliexpress.ru/item/1005003582355741.html 4x M2*8 SHCS FPC 1.0mm-15P Cable Extension Adapter…
Redesigned the bracket to work with the elegoo neptune 2 which doesn't have the top channels on the aluminum extrusions. I also modified the case for the screen to allow access to the brightness dial and screen flip switch. Category: 3D…
I created a mounting bracket for the BigTreeTech PiTFT50 screen to fit on an Ender 5 Plus. The design is in 2 parts (plus the retaining clips). Because of the way it's designed, you can still mount the Pi on the back of the display if you…
This mount allows the replacement of the built in Anycubic Mega X screen with a Bigtree Tech 5" PiTFT. It requires no modifications to either the display or the Mega X, all you need are the 4 mounting screws from the original display, 6…
This is a Bigtreetech PITFT50 Display shroud and mount designed for the ender 3, it is designed to be mounted where the original stock display is mounted. Unfortunately this design does not allow for the raspberry pi to be directly…
This is an enclosure/mount I designed for the BTT PITFT50 for my HercuLien V2 printer. I use to house the screen and rasberry pi which runs Klipper and Klippersreen on my large format printer. Most of the time I just use the web interface…
Done quickly in tinkercad. Works, but could do with being designed from scratch in CAD.
A case to mount a Raspberry Pi and the BTT PiTFT50 Touch Screen to your printer with 2040 profiles, to run printer management software like Klipperscreen with Klipper, or OctoBTT with Octoprint. Designed for the Creality CR-30, but will…
This is a display case and an articulating hinged arm for the BTT PiTFT50 display. It is designed for the RatRig V-Core 3 printers but will work on any printer that uses 3030 extrusions. The display angle can be adjusted using a friction…
Display for MK4 printer that I use with Octoprint or Repetier Server Material needed PiTFT50 Display…
An enclosure for the BTT 5.0" screen V2.1, the one with orientation & brightness buttons at the top. The RPi needs to be mounted on the supplied 25mm spacer or you have issues with the wifi. There's a hole on the back access cover that…
Modified the screen cover for BTT PITFT50 2.0 screen
Mirrored the original to use on left left side. I have it mounted on my Ender 3.
I redesigned the LCD & Touchscreen front panels for my printer made at home and I modified them to be fitted on my Prusa MK3S also. The LCD & Touchscreen support will mount using the same screws of the original, but be aware that you need…
I printed the holder in ABS with the following print specs: - 5 top and bottom layers - 40 % infill - 0.4 mm nozzle and 0.40 mm width - 0.2 mm layer height I also printed the front with the part facing down (to get the print bed surface…
Dropped 45deg pitft50 mount to clear Clicky-Clack door. Added +10mm to extrusion mounting surface of mount. Utilizing Alego's PiTFT50 mounting plate for deeper screen recess.…
bill of materials: name info 1x BIGTREETECH PI TFT50 V2.1 https://biqu.equipment/de/collections/lcd/products/bigtreetech-pi-tft43-v2-0-screen-board 6x M3x4,6 heat inserts – short 4x M3x6 frame 4x M2,5x8 SHCS 4x M2,5 washer mounting screen…
I created these models to add a BTT PITFT50 screen to the bottom of my RatRig VCore 4. The screen mounts (slider_mount_l and slider_mount_r) attach to the bottom of the front extrusion using M6x20mm screws and T-Nuts. 4 x M3x4mm SHCS are…
![Case for BigTreeTech PITFT50 V1.0 and Raspberry Pi 4 Model B [source available]](https://media.printables.com/media/prints/581604/images/4642964_c89680a9-52c5-42f5-8a9a-f1a184770f4b/btt-pitft50-rpi4b-case.png)
