Liczymy pasujące modele…
A simple "twist" lens cap for Rolleiflexes and Rolleicords with "Bay 1" mount. I made a couple of versions with film reminders (100, 125, 200, 400, 800, 1600 and 3200) as well as a plain one without numbers…
This phone holder model is designed for tripod Rollei Compact Traveler Star S1. It probably fits other Rollei tripods as well. The mount fits perfectly with no play, no movement. It is advisable to print the knob with at least 50% infill…
Hey there, Got a Rollei XF35 on a flea market and couldn't find any similar battery, so i redesigned the original cap to fit a LR44 battery instead. Light meter now works fine, but remember to compensate by adjusting the ISO/ASA of you…
Since the original lens cap was pretty loose on my model, I designed my own version that attaches magnetically. To be fair, it's not an extremely tight fit, but it's way better than before. Considering that I'm gentle with the camera…
The light meter of the Rollei 35 can drain the battery if the camera is left uncased in a lit location. And if there is film in the camera you have to rewind it before you open the camera back to change the battery. That was a poor design…
This lens hood is made for the Rolleiflex Old Standard (K2) with a 28.5mm outer diameter taking lens. It replicates the design and size of the original and will also fit other cameras with the same filter size and a square film format.…
Who is this for? This lens cap is originally made for the Rollei 35 TE. I haven't tested it for other models, but I assume it works for other rollei 35 models with the "Tessar 3.5/40"-lens The model is not made to work with filters, but…
I've designed a 43mm filter thread for the rollei. It's the largest thread I could make without interfering with the light sensor which is very close to the lens. It's push fit and twist to lock it in between the ribs of the lens. Take…
I really liked the slim design of the original lens cap. But I wanted to be able to attach a strap to it, so I won't be loosing it so easy. Also I liked the Rollei logo as an imprint more than the actual camera model. Printed in PETG,…
This is designed as a replacement for the lens cap of this 1930's Franke & Heidecke Rolleiflex. The design has been simplified and adjusted to make it more suited for 3D printing, while still maintaining the general look of the original.…
Rollei 35 SE/TE slide replacement without the solid wall on one side to prevent golden power battery contact problems due to tolerances. Locks in place and can be ejected with the small battery lever.
This is an adaptor to fit the Rollei Heidosmat 150mm f/2.8 to a Copal 3 Shutter. As different copal 3 may have different thread size, adjust the parameter in the SCAD code to your needs. Ensures that threads.scad and modules.scad files…
A simple "twist" lens cap for Rolleicord V. Note! For an updated model that should work for all Bay 1 cameras, follow the link below: https://www.printables.com/model/499657-rolleiflexrolleicord-bay-1-lens-cap…
An antique camera like the Rolleiflex 2.8 c needs protecting. In this case since there was no original lens cover, this 3d model was made so that those irreplicable lenses would be protected when using this still functional camera.
Keep the filter on and place this lens cap on to protect it. Suitable for TLR Bayonet 1, Aires reflex, Rolleicord, Rolleiflex and others. Filament: PETG Which one to print? From left to right: Lenscap for Rolleiflex with bay 1 filter on,…
Tired of using the hot shoe on the bottom of the Rollei 35 for my light meter, I designed a cold shoe for the top of the Rollie 35. I used 3M VHB double-sided tape to attach the cold shoe to the Rollei 35. I provide more details about…
The cold shoe also doubles as a loop for a neck strap. just slide it over the round strap lug and though the flat strap loop. It should have a tight fit.
This Quick Release Plate is compatible with all Arca-Swiss style tripod heads. To fit the small body of the Rollei 35, I reduced its length so it doesn't stick out at the front or back of the camera. I also added a small window so you can…
The Rolleicord V (1955) is a great companion and I use it often, but it lacks a cold shoe that can hold a light meter or a small flash. This became quite evident when the Reveni Labs light meter arrived, so I made one suitable to hold the…
Just a simple, quick model for those who want to design a functional part for the Rollei 35 camera, but dont want to go through the hustle of measuring every millimiter of it. I wanted to design a case for my Rollei 35 but I didnt find…
I made this battery tray for my Rollei 35 SE it should fit x4 SR44 or 675 batteries. I t fits perfectly without the batteries but as they are a little bit too thick, it's harder when they are in the tray. Maybe in the future I'll add a…
Print with the writing facing down. Add supports to the end of the 4 overhanging tabs - or just use the attached 3mf file which already has this supports configured. To screw it on your lens, align the external indicator line with the red…
A simple cap for the backside of SLR style Rolleiflex cameras. The small version is suitable for longer lenses. I personally tested it on the Carl Zeiss 250mm f:5,6 version. Meanwhile the larger version is suitable for all Rolleiflex SL…
A Bay II hood for Rolleiflex with cold shoe attachment
Use a thicker double sided tape to fasten on the metal exposure table on the back of the camera.
Hello :) This is a little friction-fit lens cap I designed for my old Rolleicord II (first version with Triotar 3.5 lens, I don't know if it will fit others). It holds mainly on the taking lens and has little legs not to twist away from…
Eine Schnellwechselplatte (ohne Schraube) für den Kugelkopf eines Rollei C5i Stativs (Arca-Swiss-Anschluss) Das Model ansich ist eher mäßig nützlich, weil es entsprechende Platten günstig zu kaufen git, sondern eher als Basis für…
This is an original, 3D-print-friendly reinterpretation of a classic clip-on rectangular lens hood, inspired by the vintage NKOBE 200510 accessory. The model has been redesigned specifically for modern 3D printing , with adjusted geometry…
A simple front cap for all lenses compatibable with the Rolleiflex SL66 and SL6000 camera family. That means any lens that has a Bay VII mount should fit this cap. I printed the model with no problems on my Sovol SV06, but be aware that…
simple adapter to set up the rollei r 100 webcam on the autodarts cam arms keeping the original cam case cover.
Rolleiflex 2.8 camera, employs a bayonet mount to fit some accessories, as lens caps, lens shades and filters. Rollei filters, are very rare to find and always expensive. There are on the market, adapter rings to fit screw type filters,…
Apply some pressure with your palm and screw on Category: Camera
Dies ist eine einfache Stativbein-Halterung für einen Rollei-Kabelauslöser. Die Halterung wird einfach auf das Stativbein geklickt. Die Halterung wurde für einen Stativbeindurchmesser von 32mm entworfen.
Cover for Rolleiflex SL66 Magazines, Support partially required.
I have tested the adapter with three variants of Hasselblad viewfinders and one example of a Kiev viewfinder. They are very similar, but the interfaces are not exactly the same. This adapter has sufficient clearance to work with any of…
Version 2 – Lens Cap for TLR (Bayonet 1) with Mounted Filter With this design you can keep your filter on and simply place the lens cap over it to protect your TLR lens. Compatible with TLR Bayonet 1 (Aires Reflex, Rolleicord, Rolleiflex…
Filter boxes that match your filters! Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: No Infill: 20% Category: Camera
This is a softbox for the Rollei LUMIS Slim LED S RGB Light. You simply put the light in the bottom of the softbox and cover the top with a piece of cloth. Ideally you use a special cloth for softboxes, but you can also use a simple piece…
Gleitstücke (Schalen) für Rollei Ci5 Alustativ. Anycubic PLA: Im Prusaslicer bei 30mm/s und 0,15mm Quality. Das Filament PETG weiß mit PLA Einstellungen und Bett 80°. Stützen nur auf dem Druckbett senkrecht stehend gedruckt. Besseres…
Simple Lens cap model that retains itself on the knurls on the lens.
If it is too loose, reduce the size of the model in the slicer by 1-2 percent or stick a foam sticker to the top edge like I did
Simple Adapter for your Rollei Colbor LED Lights with a missing holder for a translucent umbrella or other rods with 8 mm in diameter. Print with PETG or some other durable materials (PA-CF). .2 mm Layer height is fine. Use Supports for…
This is a clamp extension for the Rollei camera mount for tubes. It extends the fitting diameter to around 35mm. It was designed to fit my bike stem. You can use this clamp with the screws of the original part. Print on side to get the…
Designed for use with these GoPro mounts from @Dzino , I used number 2. The holes can be a bit tight depending on your print quality, but with enough pressure, an M3 screw will bite and hold the parts together.0
The model is simple to print. Throw in supports how you decide. The gap for the phone is 1cm wide. The license has to be chosen like this because I created this model in Fusion360 student license. I personally don't care what happens with…
Rolleiflex SL66 viewfinder mask for6 by 4.5 film backs. Hope it helps with composition.
The original rubber eyecup has gradually crumbled away. I designed a new one. Printed with TPU, it could possibly be more durable than the original. The eyecup must be printed with supports. Print Settings Supports: Yes Resolution: 0.2…
This model is and adapter for the Rolleimat Enlarger stand so it can take a cheap run of the mill tripod ball head. This way you can use it as a copy stand and scanner. Designed to be printed without supports. The insert for the nut is to…
Ein einfacher Adapter, um das Rollei Lumis Mini–Ringlicht Bi–Color über ein Canon EF Makro 100 1:2.8 L IS USM für Makrofotografie zu setzen. Keine Stützen bei Druck notwendig.
Maybe sometimes you don't want to take that expensive Rolleiflex out into the harsh world. This adapter plate permits mounting a Lubitel 166 TLR to a Rollei pistol grip. The adapter is also angled 18 degrees from orthogonal, because I do…
Resize to fit the Rollei 9S Cube lens.
As the name suggests.. made it for my Rolleiflex 6008 that has bayonet 6 fixture. made for my 80mm f2.8 planar lens. Remixed from a lens cap and a 77mm filter thread which I downloaded ages ago and cant remember where I got it from. I…
This is a remix of the battery cap for the Rollei XF 35 camera. It includes two distinct versions designed to replace lost or damaged original battery covers, featuring tweaked and improved thread/locking tolerances for a smoother fit.…
My tripod broke, so I designed the replacements I needed. One leg broke out of its holder which I could fix using the leg holder. Simply sand the broken part inside the tripod flush, push the leg in and superglue the parts in place. Print…
Primary mount is designed for "industrial" iPhone look (model 12+), but tried to mount 11 Pro Max and works as well. Ofcourse you can extend it on X and make bigger mount space. Thanks Mig
Unfortunately the accumulator of the bullet cam loses the main part of his capacity within the first year. To record a full bicycle tour there is not enough power left. To power it during the tour the original protective cap must be…
Při použití redukce závitu u Rolleiflexu Old Standart má snahu se fotoaparát volně otáčet a povolovat na stativu. Vytvořil jsme redukci mezi stativovou desku a fotoaparát. Vše může zůstat na místě. Zadní dvířka jdou otevřít i s nasazenou…
Arcaswiss-Aufnahme für Rollei Batteriegriff für LUX-Serie Gedruckt mit PETG 0,2mm
Um den Standort der Rollei ipc-88 etwas flexibler zu gestallten, habe ich einen Halter für Wand/Decke/Boden gemacht. Auf den Bildern ist noch der Prototyp davon zu sehen der noch keine Wandmontage kann und die Aufnahme etwas verdreht…
Very simple little replacement cover for the bottom red window on a Rolleiflex Old Standard. Has an extended section to allow easy removal without the use of fingernails, but this does then likely need to be printed with supports enabled.…
As no adapters were available online on short notice, I decided to design and print an adapter myself. Print information: Setting Value Infill 30 % Walls 6 Supports enabled, tree, paint-on as required Material PET-G Print orientation Lay…
I use a 4.8m Rollei light stand for portable hamradio antennas. This adapter is used to level the tripod in uneven terrain without modifying the tripod itself. Diameter of the stand leg is 25mm. You will need a two M10 Nuts and a M10…
Very simple little replacement cover for the bottom red window on a Rolleiflex Old Standard. Has an extended section to allow easy removal without the use of fingernails, but this does then likely need to be printed with supports enabled.…
I have tested the adapter with three variants of Hasselblad viewfinders and one example of a Kiev viewfinder. They are very similar, but the interfaces are not exactly the same. This adapter has sufficient clearance to work with any of…
I use a 4.8m Rollei light stand for portable hamradio antennas. This adapter is used to level the tripod in uneven terrain without modifying the tripod itself. Diameter of the stand leg is 25mm. You will need a two M10 Nuts and a M10…
Works with this 32mm bulls pirit levels: https://www.amazon.de/dp/B0DH15TCTM?ref=ppx_yo2ov_dt_b_fed_asin_title Clip on is for a 40mm rod. Designed for my Rollei 4.8m light Stand:…
As the name suggests.. made it for my Rolleiflex 6008 that has bayonet 6 fixture. made for my 80mm f2.8 planar lens. Remixed from a lens cap and a 77mm filter thread which I downloaded ages ago and cant remember where I got it from. I…
Keep the filter on and place this lens cap on to protect it. Suitable for TLR Bayonet 1, Aires reflex, Rolleicord, Rolleiflex and others. Filament: PETG Which one to print? From left to right: Lenscap for Rolleiflex with bay 1 filter on,…
I printed it on a Bambu Lab A1 mini using the "0.16 mm Optimal” profile with 25% gyroid infill.
Rollei 35 is already very small, and I think all the versions on the website have a slight impact on its actions. So I made several mini lens covers for the Rollei 35 camera, which are invisible, insensitive, and protect the lens. You can…
Printed in PLA, sanded lens barrel and glued on with two-part epoxy.
Printed in PLA, sanded lens barrel and glued on with two-part epoxy.
Gridfinity holder for the contents of the Rollei Camera Cleaning kit Travel
Works with this 32mm bulls pirit levels: https://www.amazon.de/dp/B0DH15TCTM?ref=ppx_yo2ov_dt_b_fed_asin_title Clip on is for a 40mm rod. Designed for my Rollei 4.8m light Stand:…
Just snaps onto the plastic peg of the rewind lever, as shown in the pictures. Might work for other cameras with a similar peg for the knob, about 3mm diameter and 3mm height. Print with an 0.4mm nozzle or smaller. Layer height 0.2mm.…
Give your Rollei 35 the stand it deserves. This custom PLA base was designed specifically for the classic Rollei 35 analog camera, combining a secure fit with a simple, elegant look that highlights the character of the camera itself.…
My Bike mount broke so I made an replacement part. Printed with PETG and 100% infill.
Accessory inset for Rollei pano head Usable for attaching a remote control receiver to one of the triangular cutouts in the Rollei panorama head. Assembly required: 1x 1/4" tripod screw.
i needed something to store and transport my RL410B batteries for the rollei action cam 400 and created this little case. prints without support to make sure your slicer scales the .stl corret user this data to check: X 40 mm Y 46 mm Z 44…
![Rollei XF 35 LR44/SR44 Battery Cap Adapter (Improved Tolerances) [WIP]](https://media.printables.com/media/prints/627a30a7-7ee4-4b57-a0af-a2dc31cde9d0/images/13553696_774a7184-10a2-492c-919c-37905c7318d8_d2428551-2e48-43f2-8116-812ca17852bc/viewcapture20260811_142616.png)
