Liczymy pasujące modele…
A simple but suitable filament spool guide for the Space Pi X4 and X4L filament dryer from Creality. This prevents the spool from jamming when it's almost used up. Because the spool is too light, it can cause the spool to skew. This can…
A heat shield designed to stop hot air in the Creality Space Pi X4 and X4L from blowing directly onto the filament spools while drying. I found DJR Engineering 's heat shield on Makerworld . It was too flimsy for me, though. So I designed…
Added templates and large desiccant box. Some other minor changes.
I created this PTFE tube cap with filament pass-through as my tube would get pulled/pushed back into my Creality SpacePI from time to time
BOM（I didn't actually buy these items） M3x10 Flat head screws(Within 15 mm) x16 https://s.click.aliexpress.com/e/_olr2kJl 608z bearings x16 https://s.click.aliexpress.com/e/_oCpbWDp badge reel x4 https://s.click.aliexpress.com/e/_oFCAgZp…
(**Copied from original part description, all credit to Spam N Rice**) Easily removable dessicant holder for the Creality SpacePi x4 filament dryer. There is very little extra space in the dryer to add a dessicant holder. This design…
Note: This is not the final version, as I don't have an INDX yet. As soon as I get my Founders Edition, I plan to add mounts for PTFE tubes or INDX filament sensors. My goal is to do this with little to no modification to the existing…
The best Filament warmer and dryer in one can now be placed on TOP of the Prusa Core One! The cross bar is only if wanted (Hexagon long stick) for more stability, and 5mm will also do in thickness at the back, but I recommend two times…
Remixed to remove the poorly fitting prone-to-spilling door, reinforce, make more printable, and add a slot for using a funnel and a sliding lid - most of the small AMS desiccant holder/pod lids and funnels work, I tested with the…
Print out the two trays, base and base pins and slide components together with the base on the bottom, add the four base pins, add the lower tray and then the upper tray. There are long print times for the base and trays due to the slow…
Two-Piece Dust Cover for the 3dconnexion SpacePilot Pro With easy to print thread. I don't know what to say… it's arguably the best design for the task :)
This threaded stop for PC4 fittings prevents your PTFE / Bowden tubes from being pulled into a Crealty SpacePi X4 filament dryer. Each stop uses two PC4 fittings. Models are included for PC4-M6, PC4-M10, and PC4-01 NTP fittings. It's held…
Allows for easier filament set up compared to other models thanks to its removable design. Three versions available Standard size - 4 mm hole for the PTFE tube - this worked for me with the original BL tube Larger size - 4,2 mm hole for…
After finding the original version was a bit tight with certain filament roll combinations, I tried to edit the original files. This proved to be a bit difficult, so I opted for a complete rebuild in Fusion. A complete RECAD of Luis…
I wanted to be able to print nylon filament directly from my SpacePi, but the filament would have needed to make way too sharp of a curve. By adding this small adapter I am able to run some capricorn tubing directly from the SpacePi to my…
Replacement palm rests for the 3dconnexion sp1usb spacepilot, a plain and two different textured ones.
The Problem In my Creality SpacePi X4, filament spools fall into the crevice at the edge of the spool roller and get stuck, causing filament to not feed to the printer. This fix prevents spools from falling into the outer crevices. For…
Container for drying desiccant (silica gel) in a Creality SpacePi X4 filament dryer. I previously used this container , but my model has several advantages: My model is designed for the SpacePi X4, not the normal SpacePi. The roll…
this is a silica gel desiccant holder that fits in the Creality SpacePi X4 Filament Dryer it takes about 37g of filament (ASA) and holds about 90g of desiccant. it fits onto the same Feet as in @evi1gasm model Some quirks in the model due…
I made this so i can easily route two spools filament from my Creality Space Pi Plus to my Creality K1 max. Layer height 0.2. used 5 walls , just use as many as you would like Its a small piece so wont take much time so better make it…
SpacePilot Pro is heavy so i added more back support to make it more stable. 50% infill. Monero address: 83d3kbWybpUayehL3jX4YXT4gu3zxWyAKPtgKvQR996pbYRnshBGkhqdMMtvF c4ETEjjQKwk9b5jTD6cJkRrcbfeEVieTRv Bitcoin address:…
The key is designed to make it easier to unscrew the nut from the “ Creality SpacePi Space Pi X4 Compact Spool Auto-Rewinder Mod ” project. I had problems unscrewing the nuts. They were difficult to loosen, and the grips are very narrow.…
These drying trays use a weaved design I have first seen in this model by Kie . This allows for very fast printing of meshed sidewalls with nearly zero retractions. A very elegant design that I copied for this model. I designed it for…
If you find my work useful you can: paypal.me: https://www.paypal.com/paypalme/printyourfix Visit my website for contact form: https://printyourfix.com/ Follow me on Instagram: https://www.instagram.com/printyourfix/ Visit YT channel:…
Grommet Piece for Creality SpacePI filament dryer, Includes varying thickness collars to hold Grommet Nozzle from 2.8-3.28mm thicknesses
This is an adapter for the Creality Spacepi x4 to use smaller spools. Requires two 608ZZ bearings per each support.
Adjusted the original model to snugly fit on a 4mm PTFE tube.
A simple, stackable, desiccant drying tray for the Creality SpacePi X4 and X4L filament dryers. The grips make it easy to put it in and take it out of the dryer. You can stack about 4 of them per side. It holds about 350g of desiccant,…
I made this so i can easily route two spools filament from my Creality Space Pi Plus to my Creality K1 max. Layer height 0.2. used 5 walls , just use as many as you would like Its a small piece so wont take much time so better make it…
The best Filament warmer and dryer in one can now be placed on TOP of the Prusa Core One! The cross bar is only if wanted (Hexagon long stick) for more stability, and 5mm will also do in thickness at the back, but I recommend two times…
(**Copied from original part description, all credit to Spam N Rice**) Easily removable dessicant holder for the Creality SpacePi x4 filament dryer. There is very little extra space in the dryer to add a dessicant holder. This design…
The key is designed to make it easier to unscrew the nut from the “ Creality SpacePi Space Pi X4 Compact Spool Auto-Rewinder Mod ” project. I had problems unscrewing the nuts. They were difficult to loosen, and the grips are very narrow.…
