Liczymy pasujące modele…
The TC420 and TC421 are very nice and relatively cheap LED controllers for fish tank / aquarium lights. However, there is no cover at the connections, so I created a two-piece cover. The lower part will be screwed in permanently. The…
Wydruk około 1,62 €–1,98 € nettoWstępna wycena jednego wariantu
65mm Makita trim router bracket for Two Trees TTC450 pro debranded from original found at Makerworld
An adapter plate is required to mount a 500W spindle on a TTC450 milling machine from TwoTrees. The drill holes in the aluminum holder of the spindle have a distance of 57mm and 20mm On the backside, melt the M6 nuts into the plate using…
65mm Makita trim router bracket for Two Trees TTC450 pro. shorter distance between holding plate and milling cutter center. Overhangs have been removed as far as possible I printed the adapter from PETG. Layer height: 0.2mm Number of…
fits https://www.aliexpress.com/item/1005002037282584.html bolt distance is 80mm
Cable holder to fix cables on YX Two Trees TTC450. Use holes original in X axis holders and replaces original cable ties, uses original holes in YX holder. Print one cover and 2+2 pins and locks. Cover positioned on bed as U, no supports…
1x https://www.amazon.de/dp/B09QM4DLKK?ref=ppx_yo2ov_dt_b_product_details&th=1 Schrauben/Screws 1x M8x20 + 2xM3x12 Selbstsichernde Mutter/Self-locking hexagon nut 1xM8 Beilagscheibe/Washer 4x M8 8,4x16 Kabelbinder/Cable strap 2x T-Nut 3m…
Erstmal vielen Dank für die Idee. Ich musste allerdings den rechten Absaugstutzen ändern da sich meine Absaugung links befindet. So konnte ich den Schlauch über die Traverse führen und mit selbst erstellten Klammern fixieren. So…
Seal can be pushed with old or new nut. When the tool is fully in, the securing part of nut is still outside of thread. FTC4939 text was added in PrusaSlicer. FreeCAD file attached. I used PETG, 4 perimeters, 30 % infill.…
Fits my Quieter 4c perfectly even though the original model was for 3q. Clamps to a leg on the ZWO AM5 TC40 tripod. Quick release makes it easy to remove the Qc from the rig and use it elsewhere. Printed at 10% infill, 3 walls, in ASA.…
A cradle to hold your Heinrichs Weikamp OSTC4 while it is charging from the wireless charger. The cradle can also be used to store the charger cable when not in use. The mount for the wireless charger is slightly off center to have the…
This model was designed in OnShape All parts sliced with PrusaSlicer 0.20mm layer height with 0.4mm nozzle 15% cubic infill Print 2x strap pieces in TPU Print bracket in PLA To Assemble: - 4x M3 brass inserts to attach the TPU parts. - A…
A holder for the Xiaomi YTC4043GL sensor, enabling you to attach it using either double-sided tape or a small screw. Printed with 0.15 quality setting on a Prusa MK4, snaps the sensor perfectly into position.
This is a middle plate for the PCB of a mechanical keyboard called CSTC40.
This model requires one unit of rack space (1U) and supports attachment through screw fixation. Simply select screws of your choice and secure them as illustrated in the provided photographs. For optimal printing results, orient the front…
I made this model to fit the Two Trees vacuum system on the 800W spindle that came with the CNC machine, a TTC 450 PRO by Two Trees because unfortunately the stock one by Two Trees only fits smaller spindles. I reused the LED bar from the…
This modifies the front end of the talon claw by replacing two parts in the original talon claw model to use bearings that smooth out the prime (similar to how the Alchemist does it). This helps to lower the amount of strength needed to…
Plate adapter to mount a clamp that allows replacement of the original spindle provided with the CNC Two Trees TTC450 with a higher power router (for example the 800w router Makita, Katzu and other ) I included also the 3df file if you…
Pro CNC TwoTrees TTC450 jsem vytvořil držák pro ohraňovací frézku s průměrem 65 mm. Model je navržen na přírubu z upgradu na 500 W motor! Silnější a větší fréza přidává možnost upínaní nástrojů se stopkou 8 mm, kompatibilné frézy jsou…
I'm building an FLP Ogre and need to make the TC4 bars. Last time I used this jig, the original model wasn't wide enough for my bars, so I made it marginally fatter. Also added text on the face to indicate which side is drilled, which…
Reinforcing part to strenghten the X guide of TwoTrees TTC450 milling machine. Designed for combination with MGN12 linear guide with length 600mm and trolley MGN12H. I bougth it here but you cany buy it anywhere…
A rear diffuser and suspension link for the TC4 touring car. I made this in 2 parts so that each component could be modified and adjusted individually (make a body mount on the upper half later) this is lengthened so that it looks decent…
Direct drop in for the broken steering rack. this however does warrant the use of a servo saver since the original linkage is “supposed” to be a servo saver itself. Works best with Kimbrough 201 size servo saver, but this does require…
If it ain’t broke, why fix it? Well, there was a little fixing... The TC4U-B reintroduces the bullpup Talonclaw, now using Caliburn V4 bars instead of the V3 bars. Modern bars means modern 2 part rambase too. Blaster is otherwise largely…
Needed places to mount my receiver and my I-Laps transponder. I decided to integrate them into this backbone so that it would stiffen up the entire chassis all in one go. The ESC just tapes onto the foot of the riser part and is able to…
3D Printed positioning plate for the CSTC40 following Aneko Sakone's and Pabile's P48 plate design.
William Optics Wedge adapter for ZWO TC40 tripod Category: Hobby
Simple remix, where I just added and positioned 2 resized negative cubes. Apparently, due to mesh issues with the original model, I am unable to "Export as one STL" (Orca just crashes to desktop) and just give you the model, hence the 3MF…
Astro Power case lite 12V/48Ah for ZWO AM5 & TC40 BOM 1x Waterproof Carrying Case Zipper Equipment Storage Bag 26x16x15cm 2x GWL/Elerix EX-L12V/24Ah LiFePo4 battery pack 1x XT60E-M Mountable XT60 Male Plug Connector 2x GX16mm 2Pin socket…
Start with a ZWO TC40 tripod. Get some 1-3/8" dowels, 3D print some parts, and now you have a tripod with wooden legs. Full directions are here:…
Simple L brackets which allow you to mount a Bestarc BTC450NP plasma cutter to the top of the Forney Fornair 555 air compressor. You will need to print two of each part (2x Part A, 2x Part B). Supports might not be required, depending on…
This block-off plate is specifically engineered for the BMW ATC400 transfer case (commonly found in the BMW X3 E83 and X5 E53). It serves as a durable seal when the original transfer case actuator motor is relocated or moved to emulate…
Start with a ZWO TC40 tripod. Get some 1-3/8" dowels, 3D print some parts, and now you have a tripod with wooden legs. Full directions are here:…
A 12V red LED lighting accessory designed for the ZWO TC40 tripod to improve visibility and safety during nighttime astrophotography sessions. The light illuminates the area underneath the tripod, making the tripod legs and equipment…
This axle cap is modeled off the right side axle cap, with clearance for the centerlock rotor mount. The fit is snug to the bearings, and shouldn't have any drag on the rotor mount. Printed in PETG, 0.2mm Layer Height w/ 6 perimeters.…
TTC450 Pro – Z-Axis Anti-Play Fix A simple 3D printed modification to reduce unwanted play in the Z-axis of the Two Trees TTC450 Pro CNC router. The Z-axis on my TTC450 Pro had a lot of unwanted movement, which was unacceptable for…
Kit de réparation (création) pour STC4005. Avec le temps la corde élastique de STC4005 fini par se limer soit sur l'attache ou bien l'anneau de passage sur la bâche. Lorsque la corde élastique fini par céder, tout tombe par terre sur la…
A small bracket that holds the TC4056 in place so it cannot be pushed back or moved around. Screws dont line up but it fits in place tightly. I printed it in PETG and PC filament.
Remplace les patins d'origine du trépied TC-40. Attention : Nécessite 3 vis à tête Hexagonale 3/8-16 (pas non métrique) x 1" (long 25mm) à faire en PETG pour davantage de résistance qu'en PLA. Imprimé avec buse 0.6mm, 4 périmètres et 40%…
This axle cap is modeled off the right side axle cap, with clearance for the centerlock rotor mount. The fit is snug to the bearings, and shouldn't have any drag on the rotor mount. Printed in PETG, 0.2mm Layer Height w/ 6 perimeters.…
A rear diffuser and suspension link for the TC4 touring car. I made this in 2 parts so that each component could be modified and adjusted individually (make a body mount on the upper half later) this is lengthened so that it looks decent…
