Wyniki wyszukiwania: tm3

STM32F072B Discovery MB1076 Case

Included in the attachments is the parametric Fusion 360 design and the label design

Divider for Ryobi Link STM313K slotbox

Both large and small dividers for the Ryobi Link SlotBox PETG suggested because garages/cars get hot Supports required Don't have a 3D printer yet? That's OK, order already printed from… https://jpelectron.etsy.com

Simple STM32 Nucleo-64 Case

A little case for the ST Microelectronics Nucleo-64 Development Kit. Check the list below for compatible boards. The board should sit quite firmly in the case itself and is held down by additional screws. The screw on the left side is…

Din rail case for STM32 Nucleo-64 Boards

The spacing between the holes in the bottom is 18 mm. There are three 2 mm holes for mounting the Nucleo board. You need mini screws like DIN 7981 2,2 mm x 6,5 mm. The holes in the bottom are 3.5 mm to comfortably fit M3 screws. Other…

STM32 Nucleo-144 Case with Ethernet Cutout

A minimal, protective half-case for the STM32 Nucleo-144 development boards, with heat set inserts and screws.

Simple STM32 Nucleo-144 Case

A little case for the ST Microelectronics Nucleo-144 Development Kit. Check the list below for compatible boards. The board should sit quite firmly in the case itself and is held down by additional screws. The screw on the left side is…

STM32 Nucleo Slide Case (Nucleo 64 pin)

Slide cases for every 64 pin STM32 Nucleo boards.

STM32 Nucleo 144 slot-in case

For best effect print with PET-G (PLA is also fine, but the clips will be less flexible). Prints without supports. In the photo: NUCLEO-H563ZI

REMIX PARKSIDE X20V TEAM KSGER STM32 OLED T12 PORTABLE SOLDERING STATION WITH HANDLE

Updated 07/09/2022 A bracket has been added for use on ikea skadis or similar murals. ********************** First I want to thank the user JAAANIK for his cool design "PARKSIDE X20V TEAM KSGER STM32 OLED T12 PORTABLE SOLDERING STATION"…

STM32 Nucleo Lid

Great base by loco but I needed to throw it in my bag, so I created a lid for it. Two versions: one with text and one without. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2 Infill: 15…

STM32 Nucleo F4 / Nucleo 64 MB1136 bumper

Super-simple, minimal bumper for ST Nucleo F4* / Nucleo 64 MB1136 boards.

STM32F407G Discovery MB997 Case

Included in the attachments is the parametric Fusion 360 design and the label design

STM32 blue pill case (blackmagic programmer)

The low cost bluepill board can be converted into a blackmagic probe, which supports JTAG/SWD debugging of many targets. To do this DFU/blackmagic.bin is needed, can be programmed onto the stm32 using serial bootloader or with an STLINK.…

STM32F429-DISC1 Case

This is a functional and aesthetic case for the STM32F429-DISC1 board. Gives access to all of the necessary GPIO pins/inputs, screen, and peripherals. The case is a 2 piece design with a bottom and top shell. Assemble with 4-M3x12 socket…

Holder for STM32 NUCLEO-F411RE board

Updated : Added additional ribs for support. This is designed to have the short M3 heat-set inserts put into it. Personally, I use the ones from CNC Kitchen . I use M3 6mm socket head cap screws. This should work with all NUCLEO 64…

STM32 NUCLEO STLink Box

Hi, this is the case for STLink-V2 programmer which is part of STM32 NUCLEO boards (64 pins or 144 pins). The programmer can be separated from the board and used as standalone device. All available pins are exposed (SWD port, TX, RX, GND,…

Blue Pill Case STM32

I just wanted a basic case for the STM32 Blue Pill board. I couldn't find one that was a basic case much like many of the other cases for similar sized microcontroller boards. It has openings for the jumpers, the button, usb and…

STM32F411 Black pill simple 3D model

Couldn't find any printable case for my new dev board, so I went to design my own. While doing it, I had to model the board itself first. This is a simplified 3D model of the new Black Pill development board with stm32f4xx (I got the…

Black Pill case (STM32F411ceu6)

A simple case for new black pill dev board (version with stm32f411x, should be compatible with stm32f401x, not to be confused with old black pill with stm32f103). No screws needed, top should snap on the bottom. Bottom holes should fit…

STM32H747 Arduino Design Files

Watch the full video here : Check out PCBWay Here: https://pcbway.com/g/WQ1kw6 Waveshare microcontroller boards featured in this video can be found here: https://www.waveshare.com/esp32-s3-nano.htm?&aff_id=172582 My website with free…

High voltage 1000V Isolation Tester 1kV Curve Tracer STM32

High voltage curve tracer , isolation tester Some time ago I ordered 230VAC LED modules, consisting of an aluminium coolplate and electronics, separated only by a thin layer of isolation. I wanted to check the safety of the isolation, and…

Makita TM30D Multitool Holder / Halter

Ein schnell gezeichneter Multitool Halter zum an der Wand befestigen des Makita Multitool TM30D. Könnte auch für andere passen. Hoffe ich konnte vielleicht dem einen oder anderen damit helfen. Die Löcher sind 3,5mm im Durchmesser und…

STM32 Nucleo-144 Half Shell with Locking Tabs

A half shell case for the ST Microelectronics Nucleo-144 line of boards. Check the list below for tested boards. Many of the cases today rely on screws to hold them down. With some of the later Nucleo boards there are too many components…

Voltmeter Data Logger Continuity Diode Tester Arduino STM32

Description : This instrument has some useful functions for Arduino users. Besides being a voltmeter with data logging, it could answer questions like "how much voltage falls on the LED at 10mA current?" or "is this an IR LED or what?" by…

STM32 Nucleo mounting base with breadboard

I found plenty of mounts for Arduinos and PIs, but nothing for the STM32 Nucleo. So I made this. My board is the STM32-F446RE. It mounts to the 3 standoffs with M2 20mm bolts (18mm will probably do). There is space for a small breadboard,…

STM32 F401RE Enclosure

A very basic enclosure for a STM32 F401RE/F411RE board that utilizes a snap-fit to remove any need for screws.

STM32 Nucleo 144 Breadboard Station

A docking station for your breadboards and nucleo 144 boards. The Nucleo board fits snuggly enough on the base, but you can secure it with heatset inserts (M3) and bolts, but be careful when screwing the bolts (M3x12) not to damage the…

Thermomix TM31 Star Clutch

Draufpressen und fertig. Material muss Hitzebeständig sein.

STM32 Microcontroller Case (B-L4S5I-IOT01A)

This is a case for the STMicroelectronics B-L4S5I-IOT01A Discovery Kit. It has cutouts for all connectors on the top and sides as well as for the integrated range sensor. The board itself has outer dimensions of 90.1 x 62.1 mm and a hole…

Case for Trezor DIY (0.96' Display + WeAct Studio STM32 Core STM32F405RGT6)

Software and assembly video here: Case is ideally held together by either melting with a soldering iron or just using glue. Electronics Used (Including Purchase Links) WeAct Studio STM32 Core (STM32F405RGT6):…

Teltonika RUTM30 DIN rail mount

Teltonika RUTM30 DIN mount for following holder: https://www.printables.com/model/1453174-din-rail-bracket-58mm-heat-insert-screw-version

STM32MP157x-DK1 Case

Case for the STM32MP157x microprocessor Discovery Kit, by STMicroelectronics. Freely inspired by the Raspberry Pi 3/4B+ Case by Stramos .

Thermomix Dough Tool TM31 - TM5 - TM6

Thermomix Dough Tool - 1x for TM31 / 1x for TM5/TM6

Case for Trezor DIY (2.42 Display + DIYMore STM32F407VGT6)

Software and assembly video here: Case is ideally held together with 15mm M3 self tapping screws. Electronics Used (Including Purchase Links) DIYMore STM32F407VGT6: https://www.aliexpress.com/item/1005002186031065.html 2.42 SSD1309 SPI…

STM32 Nucleo-64 base

A simply base to hold down STM32 Nucleo-64 development board. This way the bottom pins are not touching any surface (so no shortcircuit or scratching). Additional you can put it back into the cardbox and it should not arttle around. I…

OpenFFBoard Enclosure (TMC Motor Driver / STM32 Mainboard)

This is a simple enclosure to mount the OpenFFB TMC Motor Driver & STM32 Controller stack and provide some level of protection to circuit boards. Learn more about the OpenFFB project here: https://github.com/Ultrawipf/OpenFFBoard/wiki…

Blue Pill STM32 Mount

This is a simple mount for the [initeq] STM32 ARM STM32F103C8T6 Blue Pill Minimum System Development Board. Needed one, thought I would share mine. Feel free to use this for anything. Contains 4 holes for mounting, using 3mm screw,…

STM32 Nucelo-64 case with lid

Overview This is a compact and lightweight case designed for Nucleo development boards. Key features include: Protective Top Cover: Features a latch to protect against dust, loose debris, and accidental pin bending. Safety Hinge: The…

STM32 case (BLUE PILL) USB-C

Simple case for STL32. Case is FIT without tolerances, no screws needed. Two versions: open rails top open rails bottom (You can freely mix, to made it fully open or enclosed)

Marlin 2.1 Kingroon KP3S STM32F407VET6

Marlin 2.1 Kingroon KP3S mks_robin_nano_v1_3_f4 STM32F407VET6

STM32 Nulceo-64 Case

Case with press-fit mounting for STM32 Nucleo-64 development boards. Print Settings Tested with Spectrum PLA, 50% infill, and 0.2 mm layer height. No support needed Tested Boards Nucleo-L476RG Nucleo-G474RE Let me know if it works with…

OnStep MaxSTM3.6 Box for mount on EQ5 mount

This is building on top of the design from MikeyB from OnSteps forum. You can see the original here: https://onstep.groups.io/g/main/files/3D-printables/Board%20enclosures%20%28Cases%29/Max%20series%20cases/MaxPCB%20case%20by%20MikeyB…

STM32 (FK723M1-ZGT6) Development Board Case

Summary This is a case for a EC Buying STM32H7 development board. The part number on board is FK723M1-ZGT6 V1.0. Purchased Parts The board was purchased from Amazon , but looks to be available on AliExpress, etc. as well. Qty 4 - M3.0x6mm…

Deckel Thermomix TM31

Als Ersatzteil, kleiner Deckel für den Thermomix TM31,

SSH1106 OLED Display enclosure (STM32 + W5500)

This is an enclosure I've built for my electric boat. It houses the electronics to read out the state of charge, cell voltage and temperature of my battery packs. A STM32 uses ethernet to interface with a battery management system via…

Adafruit STM32F405 Feather Case

Small case designed with the STM32F405 feather board in mind. It has a button for the reset switch and a slot in the rear for memory card access. No provision for LiPo battery connector or I2C (yet). Also tested and working with Bluefruit…

Gobelet Doseur Thermomix TM31

Gobelet Doseur Thermomix TM 31 troué pour éviter au fouet de sortir de son axe pendant qu'il tourne

stm32f4-discovery box

slight change from original removed bottom access holes (I don't need them, I access all gpio pins from the top, bottom is just allowing crap from the table to make shorts) had to cut of pieces of pcb support as on number of boards…

Greaseweazle 34pin Adapter with STM32 "Blue Pill" Case

34pin version of the 26pin case. Had to modify it a bit as the “Blue Pill” design seems to vary a lot. This case is 2mm taller to accommodate the USB connector plus a lower right angle jumper hole and larger top hole as the top pins are…

STM32F429-DISCOVERY enclosure

This is a simple STM32F429-DISCOVERY enclosure, without screws, just snap-in connections. Cack site is for dust sensor.

STM32 WeAct BluePill+ Case

I wanted to add a BTT SFSv2 to my Sovol SV08, and needed additional pins to support both the motion and runout sensors than the SV08 mainboard supported. While there are alternative approaches (including wiring the sensor to the toolhead…

Keyboard for Arduino, RPI, STM32, ESP8266, ESP32 i2c peripheral

Arduino 39 keys keyboard with i2c interface for STM32, AVR or any other microcontroller with 3.3 or 5V supply. Size 4x10 cm using 6x6 mm tactile switches. The controller (Arduino Mini 3.3V 8Mhz) is dedicated to this application, and…

Greaseweazle 26pin Adapter with STM32 "Blue Pill" Case

Little case for the 26pin Greaseweazle adapter board soldered to a STM32 "Blue Pill". Includes easy access all of the jumpers etc... so no need to take it out of the box. Top does clip in but I usually glue it for stability.…

STM32 Nucleo Case

A simple and functional case for your STM32 Nucleo board with an embedded logo lid that clips onto the base. The board can either be simply placed inside the bottom part of the case or be secured in place with the included rings (XY hole…

Storage system with NFC card, STM32 and database on SD card

Writer / reader for NFC storage system with cards of 144 byte capacity. Remember the days searching for your tiny SMD components with a magnifying glass. This is over. Type in the text you search for, hold the reader near the storage…

Ewrf e708TM3 VTX - 30.5mm stack slot

Ewrf e708TM3 30.5mm slot which can be mounted onto standart stack 30.5 x 30.5mm. Secure with zip ties. !!! DO NOT USE PLA !!! Print instructions Category: R/C Vehicles Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts: No…

STM32 Nucleo-144 Case With Ethernet Cutout and Ext. Mounting Holes

Added EXT mounting holes

Frame for STM32H7B3I-DK evaluation board

Frame for STMicroelectronics evauluation board STM32H7B3I-DK.

Frame for STM32F750F-DK evaluation board

Frame for STMicroelectronics evauluation board STM32F750F-DK.

Shroud for weact STM32H723 board

Protect underneat your board while you work on it ;) See The OnshapeLink , Modify as needed.

Compact/Portable T12 STM32 (KSGER) Soldering Station with EC3 and USB-C input

I designed and printed a custom case for a STM32 T12 Soldering station as my previous setup was a lot of pieces. It turned out a bit bigger than i wanted but still quite compact. It is quite a bit smaller than even the smallest regular…

STM32F407G-DISC1 Bumper

Minimalist bumper designed for the STM32F407G-DISC1 development board. Initial insertion of the board is tight; slide the micro USB side of the board in first before securing the board under the two 1.5mm retaining tabs. Printed on Bambu…

STM32 Nucleo-64 Case

To mount a Nucleo board to this only M3 screws are required. The holes are 11mm deep, so with the Nucleo attached at maximum a M3x12 screw can be used. M3x6 or M3x8 is probably already sufficient.

Mounting plates for original Geeetech GTM32 Pro PCB and LCD

I added some intermediate mounting plates to use original electronics with the Standalone version This is a remix from https://www.thingiverse.com/thing:398515 Category: 3D Printer Parts

Case for Trezor DIY (2.42 Display + ESP32_Mini V31 STM32F405RGT6)

Software and assembly video here: There are two sets of parts for the top+bottom+buttons depending on the screen size you want. Case is ideally held together with 12mm M3 self tapping screws. Electronics Used (Including Purchase Links)…

Mixraumverkleinerer TM31

Mixraumverkleinerer Thermomix TM31. Gedruckt in PETG. Achtung! Darf nicht in den Geschierspüler :-)

Case for STM32F103C8T6 "Blue Pill" with Goldpin Headers

This is a sleek and functional 3D printable case designed specifically for the popular STM32F103C8T6 development board, often referred to as the “Blue Pill”. Why you need this case: Whether you're using your STM32F103C8T6 for embedded…

STM32-DVM USB Case

This is a simple case for a MMDVM USB board created by N3XCC and sold at Repeater-Builder. http://www.repeater-builder.com/products/stm32-dvm.html Screw holes are not created yet as I am not sure how to implement them. I will update the…

STM32F103C8T6 mini

STM32F103C8T6 mini

STM32 Mount/Support (untested)

Simple STM32 mount/support Adjusted to fit a STM32F103C6T6/C8T6 *53mm x 22mm (untested)

STM32 Oscilloscope Enclosure - ToyScope

Enclosure for modified version of stm32 oscilloscope Remix of a firmware is here (STILL WORK IN PROGRESS, feel free to contribute): https://github.com/Kaminariss/STM32-Oscilloscope You have to use some sort of prototyping PCB, the one i…

STM32F4 Mount

I simple mount for an STM32F4VE that has a loop for a zip tie to hold the USB cable in place. Print Settings Printer: HEVO Resolution: 200 Infill: 15 Filament: Tecbears PLA+ Category: Electronics

stm32

KSGER STM32 REMIX FOR 2020 PROFILES

KSGER STM32 REMIX FOR 2020 PROFILES. Designed for my original design of Multipurpose Arm and compatible https://cults3d.com/es/modelo-3d/herramientas/miltiproposite-arm Print in the filament of your choice: Filling: 25% Quality: 0.3 or…

Box for OnStep STM32 Blue Pill

Telescope OnStep goto controller Box for STM32 Blue Pill More info about OnStep goto controller on Howard Dutton project Box FreeCAD source on GitHup BOM additions 8x 2x6mm self-tapping screws 1x Small power ship type switch size 15mm x…

STM32 Nucleo + IHM071 + heatsink

En las imágenes aparece una placa adicional que utilizo para adaptar la salida a cable plano flexible. Entre el radiador y el L6230 utilizo un pad termico. Los tornillos son de M3 rosca para plastico cabeza de allen.

Canaduino STM32 Screw Terminal board tray

A tray/holder for Universal Solder 's “Canaduino” STM32 Screw Terminal Adapter for Black Pill STM32F411CEU6 boards and similar. This exists so I don't accidentally short out proto boards on my excessively chaotic desk. Print Settings…

Thermomix Griff handle Vorwerk TM3300 und Dichtung

Ohne Stützmaterial druckbar auf der Seite liegend. Der Griff passt auf den TM3300. Bitte eine etwas längere Schraube mit Unterlegscheibe verwenden. Ich habe mit PETG gedruckt. Die Dichtung ist fester als die alte wenn man TPE druckt. Aber…

Portable soldering Station for KSGER STM32 OLED V2.01 T12

I needed a portable case for my soldering station do solder LED stripes on the go. I had a controller laying around and some 3S LiPos, so I came up with this design. You will need: KSGER STM32 OLED V2.01 Temperature Controller…

STM32 Nucleo64 Protoboard coaster duo

Nucleo boards are inexpensive, powerful development boards from STMicro for their STM32 family of microcontrolllers. Albeit they break out all the signals from 64-pins packages, they're unfit for an easy use with breadboards. This coaster…

Macropad STM32F4x1

This is a remix of the hand wired macropad VOID9 by Victor . Instead of the Arduino ProMicro this version fits a STM32F4x1 (aka "Black Pill"). I provide only the redesigned bottom part, please visit the original thing for the top pieces.…

STM32 Nucleo-144 Lid

No support. Just making sure print with the top upside down

stm32 holder for DIY steering wheel

I made a stm32 board mount to make it easy to mount on a sim racing wheel or use this mount to create any project. use: 4 m3x10 hex screw

Thermomix RepairhelperTM31 TM5 TM6 Motor Container

If you want to wash your Thermomix Motor with Alcohol. For repairing of course.

STM32H747-Dısco Display Box

STM32H747-Dısco Display Box

STM32 disco Organizer and case

17/04/2026: Added taller top cover so it can be closed while wires are connected Magnets needed are 6x3mm and are friction fit into the organizer. The screws for the top cover are M3, length does not matter. The screws for the LCD holder…

Thermomix TM31 Topfverkleinerer

Das Model verkleinert das Topfvolumen. Beim Zerkleinern von kleinen Mengen wird das Gut nicht mehr im ganzen Topf verteilt. Ich habe das Model mit PETG ausgedruckt.

STM32L496 Display Stand

This is a simple holding stand for the STM32L496 Disco board. It keeps it off the bench so things don't short out on the pins underneath.

FYSETC STM32-Mini12864 Cover with SWD and RESET

This is a remix of the STM32 Mini12864 adapter cover by Voron Design to fit the boards sold by FYSETC with pre-soldered SWD headers. The STM32-Mini12864 module is used to replace the EXP1 and EXP2 ribbon cables with a USB Micro connector,…

LQFP-64 Holder (STM32F105)

This enclosure is designed for convenient and safe storage of microcontrollers. There are also grooves on the sides for easy handling with tweezers.

19" Mount for Watchguard XTM3x Series

Angepasst an die Firewall / Router von Watchguard - XTM3x und XTM2x Drucke es auch gerne aus ... einfacher unter https://www.3dhubs.com/service/182243 ordern Category: Computer

STM32 Microcontroller Organizer

Organizer made to fit: STM32 Microcontroller Case by Martin_Url https://www.printables.com/model/671138-stm32-microcontroller-case-b-l4s5i-iot01a Adaftruit half sized breadboard https://www.adafruit.com/product/64 Includes pockets for a…

Thermomix TM31 Topfverkleinerer

Das Model verkleinert das Topfvolumen. Beim Zerkleinern von kleinen Mengen wird das Gut nicht mehr im ganzen Topf verteilt. Ich habe das Model mit PETG ausgedruckt.

buttonbox freejoy stm32

Простой buttonbox на 8 кнопок и 4 энкодера. энкодеры ec11. кнопки 12mm. https://aliexpress.ru/item/32814739163.html?spm

STM32 BluePill+ plus case

This is really a "first cut" of a case to house an STM32F103 WeAct Studio BluePill+ development board. The design prints in two parts and can be connected together using a piece of 1.75mm 3D filament as the pin in the hinge joint. You can…

Tray for STM32 Nucleo 144 and breadboard

Half-case for NUCLEO-L552ZE-Q with breadboard pockets Tray for the NUCLEO-L552ZE-Q (Nucleo-144, MB1361) with pockets for a 400-point half breadboard and a 170-point mini breadboard. Hole positions were taken from ST’s PCB design files…

STM32 herní konzole pro výuku programování

Studenti dostanou možnost naprogramovat vlastní hru na předpřipravené výukové konzoli. Výsledkem je tak pro studenta funkční hra a pro vyučující multifunkční výukové zařízení.

Macropad STM32F4x1

This is a remix of the hand wired macropad VOID9 by Victor . Instead of the Arduino ProMicro this version fits a STM32F4x1 (aka "Black Pill"). I provide only the redesigned bottom part, please visit the original thing for the top pieces.…

STM32 (FK723M1-ZGT6) Development Board Case

Summary This is a case for a EC Buying STM32H7 development board. The part number on board is FK723M1-ZGT6 V1.0. Purchased Parts The board was purchased from Amazon , but looks to be available on AliExpress, etc. as well. Qty 4 - M3.0x6mm…

Deckel Thermomix TM31

Als Ersatzteil, kleiner Deckel für den Thermomix TM31,