Liczymy pasujące modele…
These spacers are easy to print do not require supports or any glue. Don't have a 3d printer but still want these spacers? DE: https://www.megahobby-kugelbahn.de/ * Also want to sell my models? send me a message Updates 2-1-2023 Made the…
Release of the 2021 version (v4) Completely redesigned from scratch but kept most of the v3 design. I've done some extensive testing on all parts and the complete assembly so I suppose it would be fine to print. However if you experience…
I found a couple of rails here on thingiverse but wasn't satisfied with the performance results when building a track with it. Therefore I designed my own rails from scratch, including a 4 and 5 tile overspan. Check those YouTube movies…
These spacers are easy to print do not require supports or any glue. They are a remix from Matthijz98 done in PrusaSlicer and reexported as STL. Since they fit tight with themselves and original tiles I wanted to have some smaller ones as…
All these tiles can be used with the original Gravitrax. The tile are created with higher wall great for high speed applications. The tiles are printed in two parts and need a drip of glue to work, but no support. v2 Updated all the tiles…
update 5th of April Finally, the highly anticipated update to the base tile! The two part improvement was easier to print, but needed glue for good usability. I have been looking for a better solution for a long time and I think I have…
Gravitrax compatible bridge for multilayer tracks without supports
16 different insets which can be used with my basic tile. Update 8th of February 2022 added two new insets as requested by an excited user of my design ;) (1 straight, 1 long corner & 1 straight, 2 long corners) Pick the ones which you…
I divided it into two parts for better printing, if you have trouble with the overhangs. You'll need a lot of power to get through: https://www.thingiverse.com/thing:4800097 helps, normal gauss won't work Video:…
Scenic tile! Add some travel destinations for your Gravitrax marbles with the addition of the Eiffel Tower pass through tile. My wife did one setup where she put this tile in the middle of a bunch of wavy slow rails and she called it the…
This Tower is 140mm high and has an inner channel for balls. No print support structure needed. Thanks for download. 09/01/24 update outlet See video for demonstration:
These are straight rails for use with Gravitrax Print instructions Category: Mechanical Toys Summary These are straight rails for use with Gravitrax
Two kind of hammers for kicking the marbles up to speed in your marble run! The 13mm version uses normal Gravitrax steel balls. The 15mm version uses the larger 15mm steel balls which are also used for the Gravitrax scoop. I ordered both…
While many types of curved rails are available, I found that the types I wanted to use were rarely available and that many had very tight connections, making them difficult for me to use. Therefore, I decided to make my own. I also made…
Fünf auf einen Streich… Mit Stützstrucktur (nur für den Absatz unten) Standardmodell - ca. 33g (einfacher Druck) Lightmodell - ca. 23g (relativ großer Überhang, hat bei mir ohne zusätzliche Stützstruktur funktioniert)
Gravitrax Höhenstein. Passt mit originalen Zusammen und hält stabil auf der Platte. Gedruckt aus PETG. Der Höhenstein sollte mit der eigentlichen Oberseite auf dem Druckbett gedruckt werden. Support auf dem Druckbett sollte aktiviert…
My version of a high speed curve for Gravitrax, with a separate connector on the bottom that you can glue in. This makes it more easy to print. I added the Fusion 360 file if you want to use it as a base for your own creations. Category:…
This is a spacer to be used with the Gravitrax marble run system. It has been designed so that no support is needed. Various sizes have been provided for your convenience.
A funnel for Gravitrax that allows the ball to move slowly and smoothly. I've been working hard to add more practical entry points, and I'm really happy with how it's turned out. The entire funnel is held up by three rings attached to…
this amazingly fun addon for gravitrax adds a fun new twist to your existing tracks. it suddenly drops and then comes right back up, it incredibly satisfying & smooth!
This is a new extension for Gravitrax, well I haven't seen it so far although its quite simple. Needed: - Neodym Supermagnet ⌀ 10 x 5 mm - ⌀ 3 mm Pin ( a toothpick will work as well ) Just put the parts together like in the Video (I have…
A horizontal loop inset for the basic tile. Note; this design is ONLY compatible with my 6 exit basic tile. The basic tile is compatible with gravitrax. You’ll need this part to put the inset in:…
A fun rail for gravitrax. The rail is a larger wobble rail. Designed in OnShape.
These bridges give some new possibilities and can help save some spacers. Al files can be printed without any supports
I first designed the plate as one piece based on the original cardboard and then “cut” it into 4 different pieces in order to print it. Use the 4 files gravitrax_hexa_plate_top_left, gravitrax_hexa_plate_top_right,…
The spiral is modular . That means that there is a minimum set of required parts, and a few optional parts to increase the height, change the marble inlet, add stabilizer pillars etc. Marbles cannot fall out of the Spiral - no matter how…
An accesory to lift your Gravitrax-rails. Use the enclosed F3D.-File to scale the height to your needs. Contains files for: 1HU - original height 2HU 3HU 4HU 5HU 10HU Print instructions Print in PLA. No support needed.
Power Cannon for GraviTrax by uhltimate This is my Gravitrax compatible "Power Cannon". It is easy to reload and has more power to gain height. You can print it without using supports. There a two different designs. Power-Cannon, same…
This is a catcher for your Gravitrax catapult. Use it together with the original Gravitrax base stone. The special thing about this catcher is that you can use the inset to choose which exit the ball should take. Tip: Glue the funnel into…
I had two design goals. First a fast print. And second in one piece without support. For the last goal the inner plate was skipped. AFAIK this surface isn't necessary in any condition. The spacer is still stiff. Even more, now a marble…
The stones are as high as 2,5 height stones. There are two parts on every design. Print the inlay up side down and glue them together. For the STLs use the “split to object” function in Prusaslicer to split the parts. Update 2022-04: I…
This is my version of the Gravitrax compatible baseplate with 6 exits and interchangeable insets as well as corner holes for height blocks - all for the construction of flexible tracks. To be able to use this building block, you need to…
Remixed from Thingiverse User thomasdr if you like my model please leave a like there
To print in two colors like in the images, set up your slicer to change filament at approx. 10.5 mm. For best results, place a dummy cube next to the object and make sure that it is printed first on every layer so that the nozzle is clean…
Here you can find an organizer for Gravitrax rails. They are available in the three common rail lengths. The stackers fit on the original Gravitrax playfield. Happy printing!
——————- Notification: motorized lift 2021 edition (v4) is now available and includes improvements over the v3 model https://www.thingiverse.com/thing:4751904 ——————- This is the fully revised version of the motorized lift for marble…
Meine 140mm Spacer findet ihr hier: https://www.printables.com/de/model/17152-spacer-140mm-gravitrax
UPDATE: The reported issue with the bridge has been solved. Additionally, you can now downland both right to left and left-to right orientations of the bridge. This collection of GraviTrax Junior-compatible tiles contains replacements for…
140mm Spacer für Gravitrax Hier findest du noch andere größen https://www.printables.com/de/model/511208-gravitrax-spacer-50-100mm if you like my model please leave a like there
An extendable track for your marble run compatible with Gravitrax. Depending on the height, the original rails were always a little too short. With this track you can adjust the length variably. Print instructions: You can print it…
UPDATE I'm working on printing this and I think it might be a little small. The printer is having some trouble with the statue's details. I'm going to try a slightly larger model and see how it works and I'll update the files here soon.…
The elevation system to use with the basic tile to create different levels in your marble track. The sticks fit into the holes of the basic tiles and can be fitted either in; the ground plate, another basic tile or the spacer plate. The…
These raisers are made for the GraviTrax Junior marble tracks to raise the tracks for longer runs
Durch diese Brücke spart man sich nicht nur viele Höhensteinen, sondern hier können neue Ebenen geschaffen werden. Die Mitte ist zwei Steine hoch. Sehr einfacher und schneller Druck. Die Drei Steine mit der großen flachen Fläche mit…
This is a set of Gravitrax compatible 'standard' inserts. More of my models Click here if you are interested in seeing more of my models for Gravitrax Feedback is always a good thing. To encourage me or other designers to make more…
One of the cornerstones of the Gravitrax system is building at height. These columns are a flexible way to build the marble tracks in an efficient way. The advantage is that the columns together with the base plate are flexible and allow…
Level up your GraviTrax Junior fun with this compatible 3D-printed spacer! It's a nifty add-on for creating epic marble runs. Just pop it in and let the marbles roll! Will require supports and some minor cleanup work. Disclaimer: Only…
Not fully tested yet but wanted to share anyway. The goal of the design was to randomize the way the marbels are coming out.
Continue your Gravitrax marble tour around the world by visiting London and seeing Big Ben! I'm enjoying adding some scenery to our marble layouts and will be doing a bunch more. Enjoy! This is a remix of these models:…
This is a high quality curving rail compatible with the Gravitrax brand marble run. This is designed to be easy and reliable to print with minimal post processing. There is a single layer of "support" built into the model to ensure that…
S-Curve compatible with Gravitrax. Easy to print , needs only support where the hooks are (see image), all other overhangs are 45 degrees at most. Maybe you can even turn off support at all if you print slow enough and your…
UPDATE: now also includes tunnel with a slope With this model, you can print a tunnel compatible with the GraviTrax Junior and extend your marble run building options. This model can be printed without any support and assembled without…
This is a lane switcher which causes half of the balls running through the marble track to go left and the other half will travel right. It consists of to parts which can be clicked together to prevent them to be separated when storing…
Presenting the leaning tower of Pisa in a Gravitrax tile to continue the scenic tour around Europe. Have your marbles enjoy the views while using gravity to follow your pre-determined paths along the way! Printed with two different…
This is a seesaw for your GRAVITRAX marble run system. The special thing about this seesaw is that you can use it with 2, 3 or 4 balls. Use the dividers to keep the desired number of balls in the seesaw. Remember that there must be at…
An improved tile compatible with the Gravitrax brand marble run. This tile consists of a single straight and two sharp turns. No supports are required and the design incorporates a small chamfer on the bottom that nearly eliminates the…
Kompatible Gravitrax Wippe Kleine Feinarbeiten durch schleifen notwendig.
A tower for Gravitrax printed in PLA. Support not needed
v4 foundation is confirmed compatible with OEM baseplates. This foundation piece resolves a number of issues identified with other foundation pieces I've seen on this site, mainly: tile spacing, proper hex shape, compatibility with OEM…
if you like my model please leave a like there
Here are two different spacers with 9.5° and 4.75° inclination for Gravitrax marble tracks. For the 9.5° sloped spacer block, the top track entry is 10mm higher than the bottom track entry. For the second spacer block with 4.75°…
The organizer is a simple plate with 8x3 Slots for Gravitrax elements, and can store up to 24 elements. Even most special elements fit, although they will block other slots. Freecad file for easy modification included. I printed with 2…
See https://www.printables.com/@Dom360/collections/1929103 for more gravitrax junior pieces Update: updated models to not catch the marble if its going too slow
materiál PLA tryska 0,4 mm vrstvy 0,20 mm počet kusů naznačen v názvu souboru šroub M8x8 + matka 2x šroub M3x18 do otvorů 1,8mm možno zakotvit filament jako nárazník
2 collectors which can be used in my basic tile to create new marble tracks. One is the drop collector, which catches the ball from a higher level, redirecting it to a rails to continue it's journey. The other is the endpoint of a marble…
This drop tube collects the balls and guides them down through the tube. The exit of the tube is compatible with the marble rails (see my other designs). Note; this design is ONLY compatible with my 6 exit basic tile. The basic tile is…
Every gravitrax lift is motorized but not this one. That is very handy, no cables and motors, but just with your hand. You can raise your marbles to different heights. !! Now With Knob !!
Start- or droppoint for your track. the model has 3 parts. Print the parts individually.
First I needed a way to put a gravitrax tower on top of a lego baseplate, and then I needed this, a way to put a gravitrax piece on top of a lego structure. The lego side was designed to be a 4x4 lego but the gravitrax design is not the…
Here's a simple castle model on a Gravitrax pass through tile to add some scenery to your layouts. I haven't printed this yet, but when I do I'll add photos of it here. I'm planning on changing the filament between the white tile and gray…
In order to spice up GraviTrax Junior, I created a set of vertical drops, a catcher as well as a small and a big vortex to collect marbles from multiple tracks. The drops can be stacked on top of big drop towers to adjust for height and…
(25/1/4) I removed models with larger elevation differences because the ball sometimes falling off the course. I apologize for the inconvenience. --- I previously developed a Spiral Fall system capable of withstanding and adjusting for…
24/12/22 : I updated to ver. 2.1. In addition, now supports a wider range of heights. 24/12/23 : I added “6legs +30mm” ver. ----- This spacer allows you to stack genuine GraviTrax tiles on top and create higher structures. Please note…
Looking for straight extendable rails? This set/work is still in progress. The connector is very tight to get a stable connection between tiles and rails Most rails have walls to work even with high-speed marbles Easily printable - with…
After getting a request to transform a design into a printable object I've created this trampoline. It's based on the design of Christopher Jeschke which had the smart idea to use a balloon as base part for the trampoline. I've optimized…
My version of the tower, compatible with gravitrax pro, allowing you to use walls and drop the ball in the middle. Print instructions No supports needed. Tested with PLA/PETG Brim: 5mm Resolution: 0.2 mm Infill: mid-layers 60%, others 20%…
You can never have enough spacers! And as your marble run may get really high, higher spacers might be helpful :-) The model does not use round edges (fillet or chamfers) for easy printing. Version 2, 2024-01-10: updated STL files with…
No support. See me other gravitrax models : https://www.printables.com/social/38889-djedje_zr7/collections/386109 F3D files on demand
This set is designed to create an easy-to-assemble zigzag course and get a good visibility of passing balls. The design has been simplified compared to the previous version, featuring a more streamlined look and the use of different…
Continuing with the scenic tour through Paris, here's the Arc de Triomphe! I have 2 options for printing: A complete model all ready to go, just glue in the bottom ring when done printing. Two pieces that you can print in different colors…
To print with supports→ In all parts, the paths can be used in both directions except theses ones who are decribed below.
Some different magnetic gauss cannons to use with the basic tile to create some spectacular marble tracks. Note; this design is ONLY compatible with my 6 exit basic tile. The basic tile is compatible with gravitrax. You’ll need this part…
Gravitrax Finish track including Fusion 360 file. The one in our set broke so I made a new one. new Updated version with cleaned up geometry and slightly smaller nubs so its easier to connect. Print Settings Printer Brand: Prusa Printer:…
Here's a castle style bridge (medium length) for your Gravitrax setup. It's quite large, strong, and beefy so it will take several hours to print. Also, with the way the bricks are designed it might not print too well for you, but it…
We're heading over to Easter Island to see the Moai heads with this scenic tile. I suggest printing a few and having marbles run through them while they visit Easter Island. Single piece, change filament around layer 48 if you want to…
This is my Magnetic Starter for the Gravitrax Marple Run. Here, you can see how it works and its assembly: What you need: 2x Spring with 5x18mm (or from a pen) 2x 6mm Ball Magnet 10x5mm
gravitrax larger curve rail, fits between two supports. I printed it without supports or a raft, however you may need a raft if your printer isn't perfectly level. printed with a .4mm nozzle and .2mm layer height, but bigger would…
Here's a simple barn cover over a Gravitrax compatible rail. I basically combined a barn model with a double track to make this. Added a couple supports to fuse them together and was done. I have printed a couple with supports to the roof…
Printed with 0,6mm nozzle, 0,2 mm high layer and without supports
This is one example for my gravitrax parts. Another 35 parts are here: https://makerworld.com/de/models/1833676-36-different-gravitrax-parts#profileId-1958420 Dies ist ein Beispiel für meine Gravitrax-Teile. Weitere 35 Teile gibt es hier:…
It's the Gravitrax Viking house scenic tile! Saw this on Thingiverse and had to make it into a Gravitrax compatible tile. You can either print this in two parts and glue them together, or print as one model and do a filament change around…
This model is an Extension with a straight tunnel. It is compatible with the Gravitrax Junior Marble Run. I optimzied this model: https://www.printables.com/model/744471-gravitrax-junior-compatible-tunel I used the tolerances of this…
Auf der Länge von drei geraden einen Hohenstein unterschied. Ich drucke die Schiene nach Unten. Die Reste der Stützelemente und Kanten mussen leicht nachgeschliffen werden. Viel Spaß damit.
this is a ball lift compatible with Gravitrax. it will lift the balls to 8cm high. you need this motor: https://www.ebay.com/itm/403839534271 and two m5 screws. no support needed. place two short pieces of fillament in the tiny holes in…
Verwendbar im normalen Gravitraxsystem, sitzt etwas strenger als die normalen Kurvensteine von Gravitrax wurde aber den Originalen Nachempfunden.
Add some action to your GraviTrax run! 🎯 A rubber-band powered cannon that fits standard GraviTrax-compatible tiles. Cock it, pull the trigger and launch your marble down the track. Based on the design of mechanic403:…
Eine praktische Kiste für bis zu 25 Gravitrax Kugeln (13mm). Der Deckel wird hinten eingehangen und hält dank 4 10x2mm Magneten sicher auf der Box ;) A practical tray for up to 25 Gravitrax balls (13mm). The lid is hooked in the back and…
Transform GraviTrax Junior with this compatible 3D-printed corner piece! Take marbles on a thrilling ride with twists and turns. Also contains a hole so you can add your favorite accessories. Will need some support and a little bit of…
Update 12.08.2025: Added Pillars in 50mm, 60mm, 80mm, and 90mm NOTE: The “Pillars height” is not its actual height, but the total height of the tower you get using it. Example: Base + Pillar50 + Head (Another Base) has a total Height of…
