1 / 6
Magnetic Chisel Holder for 1/4" Pegboard – Holds 3, Fits Any Brand — image 1
1 / 6

Magnetic Chisel Holder for 1/4" Pegboard – Holds 3, Fits Any Brand

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Holds 3 chisels of any brand or blade width. The handle end sits in a countersink and the steel leans on a magnet bar.

Rating
0 / 5
Likes
4
Downloads
6
Makes
0
Views
25
Reviews
0

Updated at source:

Model information

Category
Organizers
License
Creative Commons — Attribution — Noncommercial

No slots, so any chisel fits

Most chisel holders have a slot for each blade, sized for one set: Narex, Stanley, Irwin or Craftsman. If your chisels came from a different set, or you bought them one at a time, they don't fit.

This holder doesn't touch the blade. The end of the handle sits in a countersink, and the steel leans back against my Magnetic Tool Holder Bar, which hangs higher up on the same pegboard. Any blade width works, and you hang the bar at whatever height suits your chisels.

How it works

  • Countersinks for the handles: three countersinks across the top, 1-3/4" (44.5 mm) across, 1/4" (6.4 mm) deep and 2" (50.8 mm) apart. The end of the handle drops in and can't slide off the front.

  • Magnets hold the top: the steel leans back against the magnets on the bar above, so the chisel can't tip forward.

  • One hand to take one out: tip the chisel forward off the magnet and lift it out of its countersink. To put it back, drop the handle in and lean the steel back onto the bar.

What it holds

  • Three chisels

  • Handle ends up to 1-3/4" (44.5 mm) across. The flat bottom of each countersink is 1-9/16" (39.7 mm) across, so most handles sit flat on it.

  • Any blade width, because nothing holds the blade except the magnets.

  • Any length: hang the magnet bar higher or lower on the board.

How it hangs

It uses the same printed screw as my Magnetic Tool Holder Bar, Epoxy & Glue Bottle Holder and Tilt-Out Screwdriver Holder. The screws go into the board first and the heads stay out. The rack hangs on them.

  • Grips the hole: the special 1/4"-20 thread is slightly oversize, so it bites into the edge of the pegboard hole and holds tight.

  • Self-centering: a tapered tip drops into the hole and centers the screw as you start it.

  • Flat-blade drive: the head has a slot for an ordinary flat-head screwdriver.

  • Locks the rack on: the underside of the head is a cone. The two keyhole slots on the back of the rack, 4" (101.6 mm) apart, have tapered lips that fit that cone, so the rack can't pull away from the board.

Prints on its bevel, no supports

The bottom edge of the back has a 45° bevel. The rack prints standing on that bevel, so the countersinks face up at 45° and the keyhole slots face down at 45°. It prints in one piece without supports.

Pegboard compatibility

  • Standard pegboard with 1/4" (6.35 mm) holes on 1" (25.4 mm) spacing

  • The two screws for the rack go in one row, 4" (101.6 mm) apart

  • The magnet bar takes three more holes in a row higher up, 3" (76.2 mm) apart

  • Tested on 3/16" (4.8 mm) thick pegboard

  • Not for IKEA Skådis or other slotted boards

Dimensions

  • Rack: 6.00" wide × 2.44" deep × 1.86" tall (152.4 × 61.9 × 47.2 mm)

  • Countersinks: 3, each 1-3/4" (44.5 mm) across and 1/4" (6.4 mm) deep with a 1-9/16" (39.7 mm) flat bottom, on 2" (50.8 mm) centers

  • Countersink centers: 1.44" (36.5 mm) out from the board

  • Keyhole slots: 2, 4" (101.6 mm) apart

  • Sticks out from the board: 2.44" (61.9 mm)

The STEP file is included if you want bigger countersinks or room for more chisels.

Print settings

PrusaSlicer estimates 1 h 14 min and 57 g of PLA for the rack on my Prusa CORE One (screenshot in the gallery). The two screws add about 9 min and 2 g. If you also print the magnet bar and its three screws with this profile, that's about 55 min and 30 g more. I printed mine in white PLA. My PrusaSlicer config file is included.

  • Printer: Prusa CORE One, 0.4 mm HF nozzle

  • Slicer profile: 0.25mm BALANCED @COREONE HF0.4 (PrusaSlicer 2.9.6)

  • Material: Generic PLA, 230 °C nozzle for the first layer and 225 °C after; 60 °C bed

  • Layer height: 0.25 mm (0.2 mm first layer)

  • Perimeters: 2

  • Infill: 5% grid

  • Top / bottom solid layers: 4 / 3

  • Supports: none

  • Brim: none

  • Orientation: the rack stands on the 45° bevel along the bottom of its back, with the countersinks facing up; the screws stand on their heads

You'll need

Assembly and installing

Check that these steps match how you put yours up, and add how many holes above the rack you hung the bar.

  1. Pick two holes in one row, 4" (4 holes) apart, for the rack.

  2. Start a printed screw in each hole. The tapered tip centers it.

  3. Turn each screw in with a flat-head screwdriver until the underside of the head touches the board. Stop there, because plastic threads strip if you overtighten them.

  4. Line up the wide ends of the keyholes on the back of the rack with the screw heads. Push the rack flat against the board, then slide it down until it stops.

  5. Stand a chisel in a countersink and lean it back against the board. Find the row of holes just above the handle, where the steel starts. Hang the magnet bar there, centered over the rack: its middle screw goes in the column halfway between the rack's two screws.

  6. Stand your chisels in the countersinks and lean them back onto the magnets.

To take the rack down, lift it up and pull it off the screws.

More pegboard holders with the same screws

Tags