1 / 7
RV Sewer connectors for standard flex hoses AND 3" corrugated drain pipe — image 1
1 / 7

RV Sewer connectors for standard flex hoses AND 3" corrugated drain pipe

Order a print of this model

We calculate the final price from your selected file. You review and accept it before payment.

Saved on this device.

Connect any combination of RV twist lock connectors, soft RV sewer hoses, and 3" corrugated drain pipe. More to come.

Rating
0 / 5
Likes
2
Downloads
7
Makes
0
Views
41
Reviews
0

Updated at source:

Model information

Category
Bathroom
License
Creative Commons — Attribution — Noncommercial

I made these connectors because flex hoses disintegrate over time if left in the sunlight, and it's tedious to install a new flex hose onto the crappy store-bought connectors (pun intended). My connectors are easier to use, make a much more reliable seal, and don't require any metal parts (reducing the risk of corrosion). I added a long section of corrugated pipe in a semi-permanent position, as an "extension cord" to reach my RV without needing to stretch out 20 feet of flex hose. The corrugated pipe stays in place, and the flex hose connects it to the RV when it needs drained (otherwise it stays capped).

Printing the connectors

  • Filament type: prefer ASA or PETG, but PLA works if kept out of direct sunlight.

  • Print with high nozzle heat and thick layers for maximum bonding (for waterproofing).

  • Make sure your wall thickness is enough to completely fill the interior... do not use sparse infill! They need to be solid for waterproofing.

  • Supports: Print all with a 6mm brim, and supports enabled. Make sure your brim bongs strongly to the base (I use 0.1mm spacing).

  • Set the support threshold angle to 30 degrees, since the threads do better without support, but some features still need it.

  • Print gaskets out of TPU, or use print them from PLA to use as a template for cutting out rubber. You can use just about any kind of flexible, durable, waterproof material for this. And in a pinch, caulking works too.

Installing the connectors

Flexible hose
  1. Use a heat gun to heat up the flexible RV hose, then pull on the end to spread out the folds and increase the interior diameter. Alternate with the heat gun and your fingers for a minute or two to get a uniform shape at the opening of the pipe. Make sure the end of the spiral wire is reachable, even if you have to cut back some of the vinyl.

  2. Guide the wire onto the beginning on the threads. The wire should ride at the peak of the thread as you screw it on, while the folded vinyl sits in the valleys.

  3. After a few turns, stop and make sure it aligns all the way around before you twist it the rest of the way on. Misalignment can cause leaks.

  4. Thread it all the way on, and make sure the end of the hose presses against the tapered section of the connector, covering all the threads.

  5. Clean the area around the end of the hose, then seal it with RV caulking, or weather-proof permanent tape (caulking is best).

Corrugated drain pipe
  1. Cut the end of the drain pipe so it's even all the way across the opening, with no cracks or tears.

  2. Screw in the connector in until you can't turn it anymore, and you see that the mouth of the pipe is uniformly stretched around the tapered insert. The sharp threads will bite into the pipe, and pull the tapered connector tight. Use heat to soften the pipe if necessary.

  3. Clean the area around the end of the pipe, then seal it with RV caulking, or weather-proof permanent tape (caulking is best).


Editing the models

I've included the original FreeCad files in case you want to adapt these to other connections. If you have any requests or suggestions, I would love to help out. I'm relatively new to 3d design, so I haven't done everything perfectly, but I have endeavored to make things adjustable without too much hassle. I learned a lot on this project, and future versions will continue to improve.

  • Each part contains interchangeable bodies, so technically the male and female versions for each connector are just hiding/showing some bodies within the part.

  • Once you have what you want visible, you can select the part in the labels tree and press Ctrl+E to export it as an STL or 3mf.

  • Use the spreadsheet (where relevant) to modify global reference variables. I''ve just learned how to do this, so I'm slowly retrofitting some of these models to be more parametric & scalable.

Tags