Full Desiccant Spool Holder for Dry Box / AMS with Hygrometer (UPDATED v02)
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
This is a full spool model to hold a 2+ lbs. of desiccant silica gel beads directly and fits the Bambu AMS.
- Rating
- 5 / 5
- Likes
- 117
- Downloads
- 655
- Makes
- 3
- Views
- 6,036
- Reviews
- 1
Updated at source:
Model information
- Source
- Printables
- Category
- Bambu Lab Parts & Upgrades
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
The full spool filament desiccant container is designed to hold comfortably 2 pounds of silica gel beads (leaving 30% headspace in the spool). The idea here is to maximize the amount of silica gel in the AMS while minimizing the number of exchanges. This spool should fit any other spool management / dry box setting. The spool measures 200mm diameter by 68 mm height, mimicking a bambu labs spool (200mm x 67mm). The model is printed in two parts and then glued (I used super glue). There is an orifice to use a hygrometer as a lid and moisture indicator (to know when to recharge the silica gel beads). Below this text are amazon links to the “rechargeable” silica gel beads (2 lbs.) and the hygrometers.
This solution is intended for those who are ok with sacrificing a spool spot to place this desiccant container, and fight with moisture (as is my case here in Florida).
Caveats / Warnings / Future Improvements:
- The model is not optimized yet, the main part prints in about 6 hours and the lid in 2 hours in a X1C at standard speed. The hygrometer opening needs supports (use Tree-auto and slim option - in Others - note activate advanced). An optimized version could perhaps print in vase mode.
- The model has two parts that should be glued together before adding the silica gel. See note below before connecting the two parts. I used crazy glue on PLA, but there may be better options.
- The main section of the spool silica container has an orifice that can be used to fit a hygrometer.
- BEFORE gluing the two parts: play around with with putting in and out the hygrometer. I sanded a bit the hygrometer interface as well as the orifice to be able to remove it easily afterwards.
- A future version of this model will try to find the balance between ease to remove/place the hygrometer, and keeping a good seal to prevent it coming off on its own. I am thinking small slots to be able to use your fingernail to remove the hygrometer with ease.
- A future version of the model will also include an alternative without the hygrometer (a lid to add/remove the silica gel) - the lid may be a screw on on the top/bottom or the side of the spool.
- IMO, 2 pounds is a good amount of desiccant to have in the spool container. This leaves about a 30% headspace which makes it safer when adding / removing the desiccant.
- The hygrometer and silica gel beads have their operating instructions, please read and follow.
- A future version may include also a rectangular orifice for other hygrometer form factors.
- UPDATE-1: A new hygrometer plug has been added to the hygrometer. The tolerances for this are close and will fit in one of two rotational directions (if it doesn't fit, rotate 180 degree). I left the tolerances very close because it is easier to file the plug a little bit than add to it to make it fit perfectly. This addition was suggested by @Doraemond_275138 and @Boosted_285384. With this plug, the desiccant spool can be used in a dryer box to dry the silica gel beads. Note that a heat appropriate material should be used for the dry box. I don't know either how the CA glue will hold with the temperature.
- UPDATE-2: The hygrometer orifice, now has a bit of space to use your fingernails to pull the hygrometer or plug out easier.
Intended Use:
- Fill the spool with silica gel beads through the orifice and cover with hygrometer (future version of lid will be available).
- Place spool inside AMS or dry box.
- Minimize the number of times you open the AMS/dry-box. Give the desiccant spool a rotation or two everytime you need to open. If there is gcode to rotate the AMS spool at will, this would be fantastic - please let me know in the comments.
- Remove hygrometer (see warning above), remove silica gel beads and replace. The ones I bought are supposed to be rechargeable - I'll test this and update this verbage to include my experience.
- Maybe if you are able to print a transparent / translucent desiccant spool, you may be able to use the color changing version of the silica gel desiccant.
Prerequisites:
- Round Hygrometer (about $2 a piece).
- Silica clear gel beads (this one is a 2 pound / 1 quart mass version) which are supposed to be reusable / rechargeable. There is a color version of these beads.
