Counting matching models…
A simple case made for the OnePlus Nord 4, with optional lens protection. I printed my case with eSUN PLA+, using regular supports in the holes for the overhangs. The walls are just 2.1mm thick, so I recommend the extra lens protection as…
I made this quick release plate for my Velbon DF-60 / DF-61 tripod, to make it work with my Hadley telescope and the tripod adapter made by Gyoenastaader .…
Just a simple holder for 0,33L cans (tall & slim cans). 64mm between the two M5 mounting bolts (standard) Works fine with PLA and PET/PETG, but PLA might break after 50 cycles or so. I have added a TPU/FLEX-variant as well, because I have…
Toroidal propeller for a 10mm shaft. Check the drawings for dimensions, this propeller will NOT fit all flipsky 65161 motors. The hole for the shaft is 10.4mm as it is likely to come out closer to 10.1mm after printing. You can edit the…
Fits tape measure bands measuring 17mm by 1500mm (1.5m) The gear ratio of the planetary gearbox is 1 to 3.8. Only add glue to the blue surface (see photos) and the extra grip rings if you want to use them, the pins are press fit.…
I made this universal phone holder for the Hadley 3D-printed telescope, to make it easy to use Astrohopper for finding celestial objects. It slides onto the middle section of the telescope and sits fairly secure without the use of any…
This is a box to replace the original box for my 17mm, 19mm and 21mm wheel lug nut sockets. It will fit sockets with an outer diameter of max 32mm by 88mm length. I printed the bottom part and the lock-tab in PETG, the top was printed in…
Simple thumbscrew for M4 nyloc nut. Prints without supports.
Dovetail bracket for red dot sights with a 20mm clamp. Made to work with the HD101 red dot / reflex sight and the Hadley 114/900 astronomical telescope. Prints without supports. Astronomy finder scope dovetail 20mm picatinny rail
Works great in PLA with 80% infill
Printable bearing for the Hadley Telescope if you want to use 18x200mm boards for making the base. I printed it laying flat on its side, 30% infill and no supports. P.S: I used 2x “IKEA Snudda” for the circular bottom of the base, they…
Just a solid wall mount for Spectrum DX8 transmitter. Works fine with Spectrum DX6 as well. Wall mount in PLA with inserts of TPU. I printed the files in standing orientation with 15% infill.
3 files: I have uploaded 3 files, one variant for the bottom part and two variants of the top part. One with text and one without. Tolerances I have designed the parts with 0.2mm of clearance between sliding surfaces, so they slide…
Just a remix of the double dovetail mount, for use with heat set inserts. Works with M4 bolts and M4x6x6 inserts.
I designed this spool holder for my 1kg eSUN spools, and to make use of a bearing I have had in my garage for ages (6205/25x52x15 - single row deep groove). It works well enough, but there is a tiny bit of sag with the 6205 bearing,…
I crafted a containment unit for the elusive TengTools Spline Bit XZN-12 (measuring 12mm x 100mm) to thwart its vanishing acts, ensuring it doesn't pull a Houdini on me. You will need two M3x20 bolts for the hinges and superglue for the…
Emergency clutch lever for Triumph motorcycles with clutch wire. Compatible with many Triumph models. I have printed and tested this using PETG-CF filalment. It seems to be strong enough to last for a few days and a few hundred gear…
I printed the original bearings in PETG, but they lack some stiffness when moving the telescope along the azimuth direction by pushing and pulling on the telescope. By adding one more spoke, I hope to reduce wobble and settling time after…
These are all currently available results.
