Counting matching models…
This bracket attaches to the wall via the screw holes in a standard US outlet box where you would normally screw in an outlet or switch. It then attaches to the WAP (wireless access point) using the bracket that is included in the box…
Designed for any power supply with 78mm M3 hole spacing on the back. Can be mirrored in your slicer software if you want to change the direction the power supply will face when mounted on a DIN rail. Originally designed for the Meanwell…
Allows for mounting of a MikroTik CRS305-1G-4S+IN almost anywhere using double sided sticky tape. The posts of the print go into the bottom of the router and then double sided tape goes on the bottom of the flat piece. Stick it where you…
Allows mounting of 3x 5 port Wago to 3030 aluminum extrusions for 3D printers
Here's a larger electronics enclosure for a VC4 500mm! This should also fit a VC4 400mm, but will require some changes to the power inlet enclosure bolt hole spacing, the mains conduit piece dimensions, and also drilling holes to mount it…
This is for those running the V-Core 3.1 beta 1 or 2 toolhead and the funssor CNC super lightweight XY joiners (see photo for the exact model - this is the lightest weight one they make). Running the stock end stops will result in your…
V1.0 now available here: https://www.printables.com/model/1374495-ratrig-v-core-filter-10 This is designed to fit a 400mm RatRig V-Core 3.1 to provide both fine particle filtration and VOC filtration. With some quick modification, you…
Simple printed piece that bolts down to the stock RatRig spool mount for the V-Core 4. The piece has printed threads for an M10x1.0 thread, which is the typical thread for the PTFE pneumatic fittings like pictured. This helps hold the…
This combines the endstop for the Y-Axis on RatRig V-Core 3.1 machines that use the RatRig toolhead (Beta 1, 2, and final release compatible) with a PTFE guide. This allows for internal spool holders to be used and to run the filament…
This enables you to mount heavier duty M12 Stud feet or leveling casters to your V-Core 3.1 & 4 printers while strengthening the frame and still allowing for it to be leveled on the floor. I disliked the idea of using the stock M8…
Finally, a way to run a Chube Air on your otherwise stock RatRig V-Core 3.1! Requires a new metal toolhead plate and Chube Air (with heater and thermistor). These are available from Luke's Laboratory:…
This protects the wires from the Z motors on a ratrig v-core as they enter the electrical compartment. These wires run on the bottom of the 3030 extrusion at the bottom of the machine and can easily snag on something while moving the…
This allows for non-destructive and reversible mounting of an August 4th Gen Wifi smart lock to a door. It is only compatible with the type of door handle found in the last image (unable to find a part number for this, sorry). There are…
This allows you to take the easy to find & affordable Chinese Lab oven and convert it over to a controller that has programmable ramp & soak features all for about $550 (including the lab oven cost of ~$400). I use this to anneal PPS-CF,…
Please refer to the Annex Engineering Documentation at Github for how to set up Belay: https://github.com/Annex-Engineering/Belay This remix allows for a more direct integration into a RatRig V-Core 4. The components are: Belay Frame…
Allows for easy routing of filament and mounting of the BTT SFS v2 if you have an internal spool holder. Shortened PTFE holder uses an M6 bolt. BTT mount uses an M6 bolt The side holders use M3 bolts.
These can usually be CNC milled for around $100-$150 from JLCCNC or PCBWay for a full set (CoreXY motors + AWD Motors, so CoreXY alone is even cheaper). These feature holes designed to be tapped so that shoulder bolts can be used for the…
This is a gasket to help better seal your V-Core 3.1 with enclosure 2.0. The size of the round opening will depend on your exact umbilical size and how many cables you have. This is sized for a USB cable for a toolboard, a second USB…
Fits the Astrodyne TDI 084S.01500.00 and 082S.01500.00 C14 power inlet. This is a high quality power inlet for 120v 15amp max 3D printers. It is normally a “snap in” power inlet and is held in place by metal tabs, but often the force of…
Uses an M6x12 and M6 3030 T nut to install underneath a V-Core 3.1 or 4. Designed for 1 inch or 25mm thick PIR (also called Polyiso or polyisostyrene). STEP filed provided if you would like to adjust it for different thicknesses. These…
Improved electronics panels for the VC3.1 400mm to enable mounting of additional PSUs (2x Meanwell LRS-200 or 350W equivalent and 1x Meanwell LRS-150 equivalent), dual SSRs (bed + chamber heater), and fixed mounting for a Raspberry Pi and…
Overview: This is a modular, stackable filter for fine particles inspired in part by the BentoBox, Nevermore, and many other 3D printer filters. It features more powerful 80mm server fans that move significantly more air, helping to…
This is a fan shroud for an octopus max EZ board on a 3D printer to direct airflow from a 120mm to the stepper drivers themselves. It is specifically designed to work with the following fan holders:…
One of the major flaws with the stock VC4 spool holder is that when the build plate gets low enough, you can no longer remove the spool to replace it. This mod allows for the arm that the spool rests on to be removed, without tools, from…
Holds your Corsair K95 RGB PLATINUM on the wall. Uses 4 screws to mount on to 4 anchors installed in the wall.
These sealing plates are designed to be bolted around 3.2mm (0.125 inch) metal AWD plates and help cover up a lot of the gaps for better temperature retention in the enclosure. These are sized specifically for a 400mm V-Core 3.1 with…
Please refer to the Annex Engineering Documentation at Github for how to set up Belay: https://github.com/Annex-Engineering/Belay This remix allows for a more direct integration into a RatRig V-Core 3.1. The components are: Integrated…
Examples of the parts I used: 15 amp lighted circuit breaker switch - https://www.digikey.com/en/products/detail/schurter-inc/4435-0377/2646545 Filtered C19 power inlet -…
This adds additional magnet on each side to the original method of preventing the corners from warping. You will need to install the original mod that this is a remix from: https://www.printables.com/model/986607-fix-corner-warp Requires…
These help better seal your chamber in a V-Core 3.1 with the Mandala Roseworks Z Motor Mounts (which you can purchase here: https://mandalaroseworks.com/products/ratrig-z-motor-mount-for-vcore-3-1 ). For the trim pieces that go under the…
These are all currently available results.
