Counting matching models…
Want a squeezer that is simple, sits flat and doesn't distort the empty end of the tube? Here's your answer. Designed for a toothpaste tube that is approximately 54 mm wide. Scale the part in the X dimension to fit your custom tube. This…
A 10 round box for 0.22 caliber long rifle. So many of the ammo boxes out there hold 50+ rounds. That's a lot to lug around if you're hunting. The friction fit lid can be slid open to dispense as many rounds as you want. Perfect for cold…
I thought this would be a a simple part to design… boy was I wrong. The reamer on the 91mm Swiss Army Knife (same reamer on the Ranger Grip series) has a curved edge, it begins at a 96° angle from the knife body and is bulged for the nail…
Two versions, one barbed, one stubby beaded. I highly recommend you print this model with the barb pointed down. This accomplishes three things: You'll need supports regardless. They might as well be easy to remove. This orientation…
Beads (vs barbs) are meant for soft tubing like silicone. Use teflon tape on the threads to get a proper seal! I was a bit lazy in designing the straight fitting and scaled the entire part down so that the NPT threads would fit. The hose…
Comes in two sizes, thick (5 mm) and thin (1.6mm). They consume about 80g and 25g of filament respectively. Obviously the thin version needs to be attached to something rigid. Scale the sign equally in X and Y to get the size you desire.
Comes in two sizes for the front and side of your shelf. 4 models total. The photo shows the large sizes. The hooks are surprisingly strong when printed with just 2 perimeters and 2 top & bottom solid layers. BUT BE CAREFUL; overloading…
All the other print sheet holders out there are difficult to use. I wanted something better. So, I created the pivoting print sheet holder! Holds 4 print sheets. The parts are meant to be held down by magnets. Magnets to hold the base in…
A bike light mount designed for the Cateye TL-LD130 / TL-LD150 and similar Cateye lights. A 6-32 screw and nut works well to secure it. It's a friction fit with the bike light, if your tolerances don't provide a tight fit, then scale the…
Holds 70 AAAs and 65 AAs. Plenty large enough for those bulk packs at costco, sams etc. After printing this design and loading it up I realized there was a “problem.” The design uses very little plastic and packs the batteries tightly…
A clamp designed for a 2.45" (60 mm) diameter vacuum hoses. Two versions: Flexible (shown in photo). Easy to pop on and off. Just enough to hold a hose wrapped around the vacuum, for example. Stiff for more holding force. It's thicker and…
The ObXidian nozzle I bought didn't come in a plastic case so the original design this remix is based on wasn't going to work without a lid. How I made this: Printed the 2x2 nozzle holder bottom out of Prusament and measured the width of…
The original knobs are terrible. Probably because they don't want to increase the height of the device to keep packaging costs low. Anyways, print two and slide them on for much more pleasant user experience!
I bought this BeaverCraft leather strop and it didn't come with a handle, so I designed one. It uses 2, #6 wood screws.
A side handle for a Rival Crock Pot model 3040. Both of my original handles were cracked and falling apart. This new design is sturdier and provides a better grip. The model fits both sides (right and left). Do not print this handle out…
These sensors are not very robust. Protect it! PLEASE be careful when inserting this model into the fan grill. It's designed to snap in. Insert the bottom edge first and then rotate the part up to insert the top edge while gently wiggling…
The handle's blind hole is 15mm deep for a secure connection. I recommend using an epoxy.
Comes in two sizes, one for a 5/16" rods and 6mm rods . Lansky rods are 5/16" and some diamond rods from the far east are 6mm. If I have enough interest, I'll redesign it to have storage slots for the sharpening rods. Let me know if that…
Designed for two 4.5" (114.3mm) long, 5/16" (8mm) diameter ceramic rods. You can buy them this short, or cut a 9" stick in half. I cut a 9" stick in half. It was quite easy. A dremel cut off wheel was used to score the stick. By the time…
5 models at various angles 15° through 22°. Crayons work really well to fill in the recessed text on the handle (photo shows candle wax which isn't as opaque). If I have enough interest, I'll redesign it to have storage slots for the…
Most methods of hanging towels are boring! This one isn't. Fully printed. No fasteners required. Print conditions: PLA or PETG (other materials have not been tested) Supports required on the inner axle track of the body. Included 3MF…
I wanted to print dozens of these tiles so I thought I was efficiently organizing the tiles by neatly placing them together as a complete pattern in the slicer. I managed to get 24 on one sheet. Turns out… putting them into a simple 5x5…
A socket rail clip for your store-bought socket rail. Mine is a Kobalt (Lowes) branded rail. Designed to be printed out of TPU (95A or 98A). Print conditions: 2 perimeters 40% infill or higher to keep the legs stiff enough from detaching…
This model is an improvement on the foam insert that comes with the CORE One Advanced Filtration System. I'm calling this foam piece the "gasket adapter" because it seems to try to adapt the non-uniform surface of the blower to the flat…
Designed for two 8.5" (216 mm) long, 3/8" (9.6 mm) diameter ceramic knife sharpening rods. Arkansas Sharpeners is the brand of rod I am using. The 15° and 20° sharpening angles are “half-angles." For example, each side of the blade is…
The hole for the sharpening rod is 6.3mm. I don't have these 6mm rods to test how well they fit. Please comment on this design if the tolerance to too large/small. I will change the design based on feedback. Unfortunately 5/16" (~8mm)…
A clamp designed for a 2.45" (60 mm) diameter.
I like keeping a clean swiss army knife but cleaning the inside with exposed blade(s) is dangerous when the knife is all soapy. These covers are friction fit and work when to all the other tools are open. These covers are designed for 3…
A Cateye light mount for a 22.2mm handlebar diameter. The design comes in two variations depending on what screws you have laying around: #4x1/2-inch wood screw PC case fan screw (5mm major diameter, 10 mm length) Print conditions: PETG…
I recommend printing this model with random seems and staggered inner seems. These two settings significantly improve a print's ability to hold liquids. Side note, are the ants not going for your sugar-based bait (e.g. Terro)? Mix it with…
Designed for 32 mm OD caps/lids on wax paper cartons. Now a days these lids made to be low-profile, cheap to manufacturer and create less waste but that causes a problem when it comes time to spruce up our coffee! They're hard to grip!…
A replacement door latch arm for your Panasonic microwave. Mine is a "the genius Prestige" model #NN-SN797S built in March 2013. The two guide pins on my latch arm broke as shown in the photo. Print Instructions: PETG is recommended. PLA…
The power cable on the All American Sterilizer models 50X and 75X has no strain relief, and the cable experiences unnecessary wear at the cable grip. Print this piece out of TPU, wrap it around and secure it with 2-3 zip ties. During…
This model does 2 things: Centers the presta valve stem in a hole meant for a Schrader valve Keeps the presta valve stem nut from scratching your rim (also makes it easier to take the nut on/off)
I like the Defiant (Home Depot brand) smart plugs, but not enough to connect them to my WiFi. I can program & control the plugs with my phone's bluetooth, but since they're not connected to WiFi, they'll sit there and blink all the time.…
The original shower door rubber bumpers are awful and make a loud clunk if you accidentally close the doors too hard. These TPU bumpers absorb an accidental hard close without waking up your partner :) These bumpers are designed to fit a…
Printing instructions: There are two print orientations: Print on its side This puts the layers in the best orientation for part strength A brim is highly recommended OR, print the part on the two flat surfaces such that the part makes an…
Did you adapt your MK4 MMU3 to your new CORE One? Then you probably don't have enough of those rectangular magnets to fill the slots on the BUFFER_HOLDER_R_R1 and BUFFER_HOLDER_L_R1 parts. Modify these STEPs file to accommodate your own…
Your sawhorse may be branded under a different name. The square tube steel legs are approximately 20.3 mm wide. Friction fit.
Printing conditions: Use clear PLA or clear PETG Vase mode @ 0.2-0.25 mm layer height 0 bottom layers ~10 mm brim Print slowly (20-30 mm/s) Use dry filament! Any moisture will cause unwanted imperfections that will easily be seen. Using…
This clip is designed for Planet Bike fenders that are 45mm wide and 20mm tall. A very common size for road bikes. Comes in two styles: Baffled: An OEM reproduction Smooth: no baffles, slightly cleaner look I recommend printing this in…
These are all currently available results.
