Counting matching models…
Wago mounts I needed a mount with two sections so I could join multiple fans on tha same line for The Filter project, while original had only three sections variants. I also chaged the model cosmetically a bit. Wago Splitter I've also…
I've adapted similar panels from the big Voron 2.4 design, I've uploaded here: https://www.printables.com/model/525452-voron-side-and-corner-round-panel-locks p.s. the part blocking the screw hole is intentional, it is only .2 thickness…
I really liked these panel locks, they look very pretty and have less moving parts than panel clips. My Formbot kit came with unusual acrylic panel thickness of 2.5, so adding a sealing foam of 3mm, my total depth should be 5.5. I've also…
Just wanted a quieter printer, when it is idle. The Pi gets hot on it's own and needs some cooling, so I designed this back for a larger fan. You can connect it directly in place of the old one. BOM: The fan is 8010, mounted with 4…
This mod allows you to replace the original carbon filter, but let's you have up to 5 umbilical cables through the back of your printer. The design allows you to have a clean wiring inside the chamber and let's you manage all the CAN…
I wanted to tidy up the wiring under my printer, especially around 24v powerline. Also I am using the heat set remix of an amazing DIN rail clip by Fabian , which was removed somehow, so I've made a mount for that clip. There is a slot to…
I wanted a stand with a very steep angle, close to 90 degrees. I've seen a very nice-looking model for the mini and used it as an inspiration. If you don't want the stand to move around add small rubber feet to it. You can barely see it…
I ran out of space in my Voron 0, when trying to fit: Raspberry Pi BTT SKR Pico KlipperExpander CanBus UTOC (from Mellow), most likely works for BTT too Meanwell RS-25-5 BTT Octopus 1.1 WAGO 211-415 To organise things better, I've mounted…
Wanted to raise my laptop screen to eye level and have some usable space below it. If wanted, you can reinforce it with some screws, but you need to use some heat-set inserts, same used for Voron builds (M3xL4xOD5). Made it a while ago,…
This mod allows you to mount the CEB pcb to the back of your printer and hide your CanBus cable management neatly in a pretty box. It goes nicely with another model I've made that allows you to route the cables via the back filter: Voron…
Introduction I tried to print and install a quite brilliant EMS made by Fizzy Tech, but found out that it requires to disassemble whole bed and once mounted and assembled back it would be not possible to move components around. So I set…
This simple mod helps you to make your toolchanger cables to point up. This helps them to move freely without entangling with each other. Each section have 3 holes: 4mm for PTFE tube 1.2mm for the metal wire, if you have one 6mm for the…
I rebuilt my printer to Tri-Zero, which uses different skirt design. And also installed ZeroPanels, which started to interfere with the mounted display. So I've modified the original mount to accommodate the display mount I was already…
This is inspired by Magnetic Door hinges for Voron 2.4, but adapted to 0.2 Additionally you can use magnets from ZeroPanels to help with the tight seal The design assumes your total thickness of the panel and foam is about 6mm with the…
Just a simple protective cap for the light bulb. It has an opening, so it does not offer full protection, but it prints nicely without any supports
My wooden wrist rest started to wear out, so I made a quick design for the new one. I have Planck keyboard with kailh choc switches, so the profile is low. I've also included the Fusion 360 file, so you can alter the height and depth to…
I was using an amazing stand by Lucendi ( Voron toolhead display stand ) for my very first StealthBurner that I've assembled. But then I needed to put 3 more heads next to it and realised that it takes quite some space. I then got…
I wanted to switch from rollers to rails on my Ender 3 v2 and use StealthBurner, as I had a spare SB2040 and full head from my other build. The carriage is a modified version of Switchwire carriage, but moved 7mm to the front, as it was…
These are all currently available results.
