Counting matching models…
Update 03/01/26: The file Vice-Body2.stl has been updated to Vice-Body2a. The original did not include the thread for the table screw. Update 10/02/26: I've updated the Vice Screw to now be comprised of two parts, a knob and a threaded…
General. Modular shelves for the 5x4 Gridfinity light cases by Suit, in 6U, 9U and 12U heights. I've designed these shelves for storing 5x4 cases in the van. To stop the cases sliding out they are held in place using a lip along the front…
General: This is a three axis, rotate and tilt vise. Similar vises that I have downloaded and printed in the past never seem to hold in position very well. So to overcome this, I've designed the axis pivots with a tooth and pocket…
A collection of conduit/pipe clips for the following sizes of conduit/pipe. Nominal outer diameter: 20mm, 25mm, 32mm, 42mm and 55mm. Maybe used for both rigid or flexible conduit. The clips may also be clipped to each other, side-by side,…
A collection of circular conduit boxes for 20mm bond in conduit. 2 off No: 6 x ½" Panhead self tappers or 2 off M4x12 Panhead screws are required to secure the lid. 1 off No: 6 x ½" Panhead self tapper or 1 off M4x6 Panhead screw and 2…
Using D Series XLR patch panels and stage boxes along with modified blanking modules provides an easy way of making custom panels. I've used these on numerous installations over the years. The files are basically blank modules with the…
A collection of blanking plugs, bushing, locknuts and washers. Blanking Plugs: for blocking off holes in metal trunking, panels or equipment racks. Plain circular with screwdriver slots (BPP) or hexagonal (BPH). Bushing: for routing a…
This fitting is for connecting a 32mm (outer diameter), square grooved, flexible conduit to a panel or equipment rack. Just because I wondered if this was possible, although it would be easier and cheaper to buy some from an electrical…
This is a redesign of Joshed's cable winder in five sizes. The cable entry to the winder is more tangential which helps reduce drag on the cable when winding it up. Mini. Outer Dia 84mm; Inner Dia 75mm; Overall Height 24mm; Capacity:…
A simple clip for holding two walking poles together. Clips poles that are 15 to 17mm in diameter. Print in PETG with 5 perimeters and solid infill.
A simple gridfinity 5x4x2 tray for holding a set of Milwaukee spade bits. Pockets for 12mm, 15mm, 18mm, 20mm, 22mm, 25mm, 28mm and 32mm bits. Note: the photos show the tray in a 5x4 case which is not included, however you can download…
This is a simple wine rack system for bottles with a diameter of up to 78mm. Three base versions are available for 5, 10 or 15 bottles. Each version comprises of an End and one or more shelf sections, i.e.,. 5 Bottles will need one End1…
I needed a gridfinity case to hold firstgizmo's spool holder . The 5x4x12U box by suit was perfect but the lid needed to be a little deeper. This was acheived by removing the gridfinity grid from the lid and adding 2mm of extra depth.
A 3x4x4 gridfinity storage tray for eighteen Hex shanked HSS drill bits. Comprises of a tray and two, clip in, hinged, bit holders. The two bit holders are numbered to indicate drill bit diameters from 2mm to 10mm in 0.5mm steps. The tray…
A range of large diameter hole saws for cutting mineral fibre ceiling tiles only . These are not suitable for cutting anything else. They are sized for cutting holes for the Penton ceiling loudspeakers listed below. However, they may be…
2x4x4 gridfinity masonry drill bit holder. Two part design with a hinged holder for Milwaukee masonry bits of the following sizes: 2 x 4mm 2 x 5mm 2 x 6mm 1 x 8mm 1 x 10mm 1 x 12mm The bit holder simply clips into the gridfinity bin.…
A modified slide for the Zinc 0.50 incorporating a short picatinny rail for optics.
A simple junction box for housing a single Zenitel/Application Solutions EOLZ01 end of line module. The EOLZ01 is a tuned load for use with the V2000 amplifier frame impedance monitoring function. By adding a load at the end of the…
My lynx was getting a standard deviation of about 22 for a 20 dart average. This mod replaces the screw head pusher with a longer ported pusher that fully chambers the dart into the barrel and directs airflow onto the rear of the dart.…
These are all currently available results.
