Counting matching models…
I really liked @episco 's OLED terminal but didn't wand to glue the OLED into the frame so I came up with this little clip to hold it in place. To install it, just put the OLED display and the the clip in place and push the clip down. Due…
I wanted to substitute the barrel jack on my DPS power supply with USB-C PD but didn't want to redesign the whole case, so I made this adaptor that fits in a 12mm opening like a lot of panel mount switches. For the PDC004-PD trigger board…
A cutting guide for straight and perpendicular cutting. I needed to cut 5-10mm thick material but had trouble cutting perpendicular to the plane of the material and ended up with the top side having the desired thickness and the bottom…
I needed a D1 Mini mount with access to its USB port, so I designed one based on the DIN rail clip by @spckr and inspired by the D1 Mini clip by @froetz . The D1 Mini clips into the mount quite nicely, but has some play when installed…
Case for a DPS5005 (or other variant) power supply module with power button, 4mm banana jacks and DC barrel jack input. Unfortunately the closing mechanism was somewhat of an afterthought and therefore requires 4 of the hooks to be…
I needed some grooved tweezers to better hold wires or pins when soldering, because even the serrations in some tweezers would allow the wire to rotate. I found the 5-064 style of tweezers from Bernstein, but since I have a 5-434 I…
The pegs can be used to adapt the 40mm spacing to the 45mm of a Netgear GS105, or any other device with that pattern. In “reverse” order, the pegs can provide a 35mm width pattern. The holes are 3.5mm to be tapped M4 and the tolerances…
DIN rail endcap to mount it between two parallel surfaces. I intended to use to mount a DIN rail with some power supplies and relays between to legs of a modified Ikea Lack enclosure. Update 2024-04-25: Added v5 with modified 50mm hole…
A holder for the USB-C power brick of a Rigol DHO800/900 series or DB858(E) device to attach to the VESA mount on the back to clean up the wiring. The power brick and its USB-C cable are attached with cable ties… … and then the holder can…
Ikea Micke desk insert for holding a lamp and 22mm socket adaptors. USB socket I used this USB-C panel mount socket. Unfortunately the included nut was too big to fit into the underside of the holder so I printed a smaller one. (See…
DIN rail mount case for DPS/RK power supply or WEL electronic load modules. Uses 12mm openings for button, safety 4mm lab sockets and power input (e.g. my panel mount USB-C PD trigger holder ) The back attaches via M3x8 counter sink…
3D printable modifications to attach an oscilloscope probe to a low cost magic arm mounted to a Stickvise: StickviseArmBase: Base that goes between the Stickvise and its jaws, onto which a magic arm can be mounted via M5 threads…
DIN rail mounted holder for oscilloscope and multimeter probes with storage space for oscilloscope probe cap hook. Tested with the shown probes, but please reach out if I can make them fit more. Prints in two pieces that fit together. The…
I wanted to give the RP2040 a try as a logic analyzer and the Scorpio is a prime candidate due to the 5V tolerant pins (as advertised by Adafruit on the Scorpio product page ). But I didn't want the Scorpio flying around my desk with the…
A holder to attach a DIN rail to the back of a FritzBox 7583. The 7583 has a very odd shape with a big cutout in the back, making it protrude quite far from the wall. To reclaim this lost space and to better organize my Raspberry Pi…
After sawing some aluminium rods and pipes to length I always end up with a bad cut and rough edges. The inside edges of pipes are easily cleaned up with a deburring tool but the outside edge is more tricky (if you don't have a belt or…
Remixed version of the @Adafruit Snap Fit Case for Feather RP2040 Scorpio for their FT232H Breakout . Modified to fit the smaller FT232H breakout and added options for no mounting tabs on bottom and embossed name. Removed mounting holes…
Remixed the the “holder” part of Bosch UNEO additional drill holder to hold 21 ¼" screwdriver bits or drill bits with hex shank before additional holders were available.
These are 3D-printable dividers for SMD component books as can be found e.g. as filled assortments on eBay etc. or empty on Adafruit . In addition to a filled book I also got an empty one, as well as some extra pages for 8 and 24mm…
These are all currently available results.
