Counting matching models…
Yet another electric powered "turbo"... but this one sucks really hard! [>1.0 psi easily] I set about designing a centrifugal compressor with a smaller rotor/shroud clearance that commonly found, in order to achieve high pressures more…
These hose adapters REALLY SUCK!!! This is a spreadsheet parameterized Freecad 0.18 file for generating printable adapters/couplers for vacuum hoses and accessories. It can make them in any size and gender, as long as it is a straight…
I designed this thing to mount a standard 2.5" SSD on a din35 rail. It has an offset to give additional room to the side where wires plug in. I added a "pry bump" to protect the corner of the SSD during removal. It prints best with no…
I designed this thing to open "brush-in-can" plumbing adhesive containers. These adhesive containers use a standardized 45mm diameter knurled lid. The lids usually become impossible to remove with bare hands after the threads get jammed…
I designed this thing to isolate dc ground from chassis ground for antennas panel mounted on metal enclosures. It is basically a pair of 1mm thick 14.5mm flange washers, with 6.5mm ID, and a 9.2mm OD 0.5mm thick flange. It mounts standard…
I designed this thing so I could use 18650 Li-ion batteries in one of my small flashlights. The flashlight is the kind that takes 3x AAA batteries in a removable holder, with a tube/cap that have ~M24x1.25 threads. This particular…
This is a remix of jsadusk's thing with added mounting flanges for use in my Tinker Friendly Ikea Lack printer enclosure. These make it very easy to disconnect/reconnect the case leds, spotlight, mixing fans, cooling fan, and filament run…
The latest in 'Cool-stepper' technology! I designed this thing to cool the z motor on my cnc, but it can be used on any NEMA-17 motor with enough clearance around the sides and back. It uses a 40mm fan. The square duct cross section…
I made this thing to replace the worn out velcro strap that came with my Stihl Magnum blower. I designed it for nylon; YMMV with other materials. It secures to the nozzle with a small ziptie, and hooks to the top corner of the blower (as…
I drew this from scratch to make it easier to remix, but I tried sticking close to smitty's original design. Smitty's box is almost perfect. My only 2 complaints were the slots are a little too large to keep the smaller Betaflight 1s300…
I designed this box for a Wemos D1 Mini powered smarthome remote. Here is the short list of the specific parts I used in this project: Wemos D1 Mini:…
Yet another grippy… but this one's kinda nice. ;) I printed with Siraya Blu on a Sonic Mini 4k printer, using Siraya recommended settings (4.5sec exposure, etc). The holes for standard brass threaded inserts are exact size. Inserts press…
I made this DIN-35 rail mount for the relay modules I prefer use on my automation and IOT projects: https://www.amazon.com/Relay-Module-Channel-Opto-Isolated-Trigger/dp/B09G6H7JDT/ref=sr_1_4?keywords=5v+relay&qid=1656290200&sr=8-4 *…
This is my remix of nogmasa's original rapidfire cover, to add room for ELRS backpack hardware. Here is a link to the original: https://www.thingiverse.com/thing:5182786 I used an RP1 elrs rx for my backpack. A DIY esp01f with…
I designed this thing to fly 1s300 packs on a Happymodel Mobula 7 frame. It has a good friction fit on the battery, similar to a mobula6/meteor65. It snaps in place so you can keep it in several packs in a row, and pop it out easily when…
I made these for my IKEA Lack enclosure, but you can use them on whatever you like. It is sized to fit a short piece of 8mm wide strip (6 leds). The fit is tight enough where you don't have to remove the adhesive backing, but loose enough…
Holds 3@ arrows of diameter ~3.5-5.5mm (freecad file provided if your arrows are a different size). This is not really a remix, but an accessory for the Mini Compound Bow designed by DonStick3l... Don thanks for the wonderful design!:…
I designed these things for my Sanwa OBSF-30 buttons, to silence the 'clacking' sound when the button is bottomed out from a hard press. Sanwa makes 'silent' buttons, which are very nice, but have a different 'rubbery' feel to them and…
I designed this thing to add a z-max switch to my MPCNC Primo. It is designed to work with the same size limit switches that are standard on MPCNC. It works with Burly style mounts, but may also work with others (the lever has to hit the…
I have a bunch of relay boards around, and needed to add one to my cnc. I figured why not make room for a second relay, just in case... that later turned out to be a wise move. BOM: 2@ relay breakout boards (…
This is a 65mm spindle mount & vacuum nozzle for the MPCNC Primo J. I started with the original Burly mount cross section, and beefed up where it attaches to the z tubes. I made an adjustable height vacuum attachment for it, that bolts to…
This is a set of 2.5" hose adapters (large shopvac hose) for Dronnn's well designed cyclone vacuum filter design, which you can download here: https://www.thingiverse.com/thing:2829268 These adapters feature an aerodynamic transition to…
I designed this thing for my Lack enclosure. It covers a rear mounted 120mm exhaust fan to prevent heat loss when the fan is not needed, and opens to direct hot air upward when the fan is moving. The flapper is 0.6mm thick to keep it…
Many hobbyists like me have a few spare male dupont style jumper cables in their toolbox. This thing to turns those spare cables into articulating probes for your DMM or scope. My design is a remix based on giufini's Octo+ PCB Workstation…
I had a mishap when I went to replace the antenna on my Meteor65 pro 2022 version whoop. So I had to replace the VTx, and decided to use a unify pro32 nano. Here's the mount I made for it. It works much better than what I did before……
Not that there is anything wrong with drilling the holes out on a Burly tool mount, but that just didn't sound optimal to me. So I remixed it for all to enjoy. The original stl file I used is the MPCNC Burly J 6-32 tool mount:…
[Edit: Also check out version 2 of my z chain mount for an alternative configuration. It uses a wedge to anchor to the inside of the z tubes from the top. https://www.thingiverse.com/thing:4705663 ] I made this thing to hold cable chain…
I designed these things to filter cooling air on an assortment of devices I own. They feature Scotchbrite scouring pad filter media, snap on filter holder for easy maintenance, compact design, and tweaks for aero efficiency. Print the…
[ Updated version... tested and MPCNC Primo approved (unofficially;) )! I removed the old STL and replaced it with new versions. Both newer versions have a shortened clamp nose to eliminate interference with the home corner parts on a…
Yet another desiccant box... 56mm tall x 50mm wide: fits in the middle of most spools (Taulman inlcuded) Hex shaped: stackable, and better airflow around the sides (more even absorption) Horizontal thin bars: less "islands" to print…
I made it thin but with some clearance, to save filament and minimize interference. I also uploaded a rounded corner version if you prefer that aesthetic. It fits nicely for me printed in abs on my a8, with an 0.4mm nozzle and 0.2mm…
I designed these things to keep underground low voltage wire splices dry and clean. There are many different products available to do this job, but most of them are either messy, difficult to use, or unreliable. I modeled the general…
I designed this duct to fit a 40mm fan on the e3d hotend heatsink (fits V5 and V6, bowden or non). I had used a similar design for several years, but it had some quirks that were annoying to deal with. I also learned some interesting…
Print this thing and you will no longer waste time locating a drill bit that got obscured under other tools at the bottom of your bag. I designed this thing to keep a set of 12 hex shank spade bits organized in a side pocket of my tool…
I designed this thing to secure a Z cable chain to the top of the Y-axis on my MPCNC Primo J. I originally designed a clamp style mount ( https://www.thingiverse.com/thing:4672652 ), but I wanted to use that hard point to add on a heavier…
djk4linux's air-assist nozzle for the Neje 40W lasers is a bit long for cutting thick materials. So I remixed it for some shorter options. https://www.thingiverse.com/thing:5073015 The original nozzle extends 15mm from the base of the…
I got tired of working hard to avoid damaging cells as I pried them out of my commercial one cell holder after charging. That thing was sized for unprotected cells, but even those weren't very easy to remove. So I designed this thing in…
This is my enclosure design for the Arducam ESP32s UNO PSRAM board, a power switch, and 900mah lipo. I use this board to do timelapse videos. It gets over 24hrs battery life snapping 1600x1200 jpgs every 5sec, and the whole assembly costs…
This thing is a GPU support, but instead of just being a bracket it also forms a duct to bring in cool air from the back of the case. I am posting this thing more so to share my general concept with others, with a very low expectation…
This is a mount for an Arduino nano v3 and 2@ ACS7XXX hall sensor boards, similar to these: https://www.amazon.com/gp/product/B01FA2P1YW/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1 I printed at 0.3mm res with ABS, but other filaments…
I designed this enclosure for a small/cheap AC power meter (with power factor) I purchased for under $20 on Amazon: "AC Power Meter, DROK Digital Multimeter AC 50-300V 20A Voltage Ammeter Amperage Volt Current Power Factor Energy…
I designed this thing to flush mount a common 7" IPS touchscreen on a flat panel. The bezel is 28mm wide; the minimum that provides a 1/4" overlay on the panel (to allow for sloppy DIY cuts). There is 0.5mm clearance between the screen…
I made this compact enclosure to mount my Neje laser tester board on my cnc machine. Neje recommends operating their 40W laser at <60C. So I made this compact enclosure to use the Neje laser tester board to monitor my the laser module…
An updated version of this thing is available here: https://www.thingiverse.com/thing:4386075 Meet YARMAUS (yet another recycled mouse arcade USB spinner... not affiliated with Yar). I'm guessing if you are looking at this thing, you…
I got a new Rigol ds1054z scope that came with Rigol PVP2150 probes (the smaller, all black kind), and I needed something to hold the probes in place on circuit boards. I had already printed this very nice probing station designed by…
I designed this enclosure for a micro amp meter project I built based on the excellent work of [email protected]: https://www.openhardware.io/view/380/Micro-nano-ampere-meter-double There you will find the source code, operating…
I thought pyr0ball's mold design was simple and worked great as far as overall fit/finish and ease of use. However the socks it produced were about 1mm too long with the nozzle tightened down against the heat block. So I remixed it to…
I designed this to fit a PTFE filament guide tube to my Presto brand dehydrator. The tube hole is exact tube dimensions. Depending on your printer and preference, the tube may be too tight. If so, just drill it out after printing to get…
Remixed chschmit's brush boot part to accept M3 nuts, so it can be bolted to the router flange. Simply drill the router flange to pass M3 bolts for a non-glued quick release Colt vac attachment. Note that the 3 vertical parts inside the…
I made this filament jam detector to ensure reliability and ease of use with my printer. I've used it through countless spools of filament now, and can say it has definitely achieved it's goal. It has a some utilitarian features worthy of…
I designed this thing to facilitate installation of composite decking boards. Similar the tools you can buy from the manufacturer of your boards, this tool will helps ensure accurate board-board spacing and screw placement. I provided a…
This is a mounting flange for Dronnn's well designed cyclone vacuum filter design, which you can download here: https://www.thingiverse.com/thing:2829268 This thing is designed to go inside your bucket lid (or whatever you use) so the…
This is my second design of an Anet A8 direct drive X carriage, intended to fit an e3d hotend, bltouch, 40mm hotend fan, 40mm part blower, and original MK8 extruder. This revision compiles a lot of ideas I had operating my A8 over the…
I made some upgrades to my "garage all-in-one" smarthome device. So I had to make an updated enclosure for it. Here is the list of the parts I used in this project: Wemos D1 Mini:…
I designed this enclosure for an esp8266 powered all-in-one smarthome device. Here is the list of the parts I used in this project: Wemos D1 Mini:…
I designed these feet to protect the bar on my Bosch T4B Gravity Rise miter saw stand when the saw is being stored vertically (love the stand BTW). They also help take some of the heavy load off of the threaded feet when tilting the saw…
After designing, printing, and installing this on my A8, I gave the tops a twist and they are now completely locked in. No print volume is lost, but it will reduce ringing. It's an easy print, and even easier to install. You should give…
This thing is meant to fix/reinforce hcooh's Dyson V7/8/10 accessory rack found here: https://www.thingiverse.com/thing:2027523 It is a remix of Blkhawkdrv's clip, with a screw added and a rounded taper cut on top so the canister doesn't…
I am giving credit to IsmaelPR1 for his a8 e3d direct mount design, which I used as inspiration for my x carriage design. His original design is unfortunately meant for 45mm rod spacing (older a8's), lacked a decent z probe mount solution…
Din mounts for rpi are great as long as there are other devices that can fill out the rail, but a pi din mounted all on it's own takes more work and uses up more mounting real estate. I was faced with such a situation while building my…
I made these spool shaped racks for drying desiccant in dehydrators meant to fit spools of filament. The mesh gaps are 1mm wide, which should not allow most reusable desiccants through. The ID of the "spool" is 2.25inch, which is the same…
This is a modification of Ryan's excellent MPCNC Primo J cnc machine design, which can be found here: https://www.thingiverse.com/thing:4493589 The stock design uses the z stepper motor axle to support the weight of the z gantry. This…
This is an improved version of my original 'Y.A.R.M.A.U.S.' spinner design, which can be found here: https://www.thingiverse.com/thing:4354590 Standard Y.A.R.M.A.U.S. Features (V1 & V2) Fits a standard Happ joystick drill pattern Dual 608…
Updated code: https://github.com/truglodite/Dehydrator I decided to hack my Presto 6302 food dehydrator to control it with an Arduino 328p. The result is a smart dehydrator that uses a table of drying profiles (temperature and time) based…
Changing the tools on an MPCNC Primo is a bit of a task. So I designed this thing to quickly swap in a laser diode module without having to remove my Bosch Colt 1hp router mount. It simply slides into a 1hp Colt mount like the router…
I made this to enjoy higher rpm, louder noise, and higher pitch when operating my air raid siren. :D After I printed myself MlePh's air raid siren (THANKS!) I gave the crank a good spin and ran in to hard friction before even reaching…
If you bought some nice new Sanwa OSBF-30 buttons for your arcade stick, and figured a 1 1/4" drill bit is close enough to use on your wood box, you probably feel the pain I felt when I saw just how loose that fit was. The 2mm variance…
This is a remix of yinyang's remix of Krohm's original mob6 adapter, in order to add M2 inserts.
I made these tool mounts for convenience on CNC's that use a 65mm diameter spindle mount. Left to right in the first photo, a Roland style dragknife, a 2.5W diode laser, a 40W Neje diode laser, and a router table stand. The STL files are…
I designed this thing to mount this 4 channel mosfet driver board to my Ikea Lack enclosure: https://www.amazon.com/gp/product/B01MRQFYJN/ This allows me to add control of several 12V fans and case lights with Marlin firmware. Of course…
I'm building a Lack enclosure for my A8 and wanted something to mount the LCD underneath. Instead of designing from the ground up, I designed this angled mount to go with sportssedan's Anet A8 LCD Flush Mount. So to use this thing, you…
I designed this front bumper antenna mount for the TBS Sourceone v3 7" quad. It has a horizontal mount that fits a standard Happymodel ELRS 2.4 dipole antenna. Due to the design of the HM antenna, making a solid and reliable mount that…
I have one of those pet hairdryers that comes with a poor air filter design, like this:…
Properly swapping the tool mounts on an MPCNC Primo cnc router is a lengthy chore. So I designed this thing to make it easier to swap between a Bosch Colt router and a Roland style dragknife. This thing just slides into the Primo 1hp Colt…
I designed this thing to secure 2.5" flexible vacuum tubing on the z-axis of my MPCNC Primo (1" ID clamp stretches to fit all versions of Primo). The design uses a slide on dovetail attachment, to give a robust/keyed in mount that can be…
Looking to DIY an esp8266 powered smarthome device that reads temperature, humidity, luminance, microwave motion, and outputs to a relay and a beeper? You found a great place to start... or finish it. I designed this enclosure for a smart…
I tried out several other online available hero3/4 mount designs for my s1v3 7", but they all resulted in major jello. So I set out to design my own, focusing on advice from Oscar Liang that a harder mounting is better than floating. The…
I designed this enclosure for a RX5808 Pro Diversity custom PCB, oled screen, LM2596 buck regulator, and LM2940 ldo. The enclosure includes a T-nut insert for mounting to tripods. More info on the RX5808 Pro Diversity project and code for…
I designed this thing to replace the keys on my Vevor brand steel enclosure with knobs. Since my enclosure is in my garage, the keys were very inconvenient. These knobs press fit into the barrel of the keyed latches. So the knobs are…
I designed this adapter to fit my Neje 40W doide laser module onto my MPCNC. The adapter slides into a Bosch Colt clamp style router mount, like the one I designed here: https://www.thingiverse.com/thing:4632040 It's designed so the laser…
This is a redraw for the spring retainers used on Claghorn's open cable chain, which you can find here: https://www.thingiverse.com/thing:611593/comments The original design is awesome, however I had a lot of issues with 1st layer…
Instead of drawing a case for to fit my new tft35 to my printer enclosure, I decided to make some brackets for BigFunkyMan's case design. The assembly fits my enclosure just like my old RRD graphic LCD used to (top mount w/ 8* tilt).…
I designed this thing to mount a mister to my MPCNC Primo J cnc router. To use this thing, you will need: 1@ Printed mount 1@ Rattmmotor brand mister nozzle (…
These EXPO fine point dry erase pen compatible parts are for use with smily77's "v2 version" of the plot clock / thermometer: https://www.thingiverse.com/thing:371248 Actually it's technically not a remix rather than a redesign, since the…
I run an elrs 2.4 dual rx on my 7" sourceone v3, and needed a better front mount to go with it. So I designed this in f360, and it works well. It features a stiff mount for less vibes, and no printed material wrapping the feed point or…
I just got a GTR board to upgrade my printer, but could not find a case that would work for me. So I sketched this up, and it works quite well. The 2x 40mm fans are centered on drivers 2 and 5, giving optimal cooling where it's needed.…
This is a remix based on my Expo fine point parts, intended to fit the larger chisel style Expo dry erase markers. To use this you will need to print the rest of the parts for a plot clock. I liked smily77's "V2" arms and PIR mount:…
I liked the plot clock body designed by stylesuxx, but I needed to add some holes for the temp sensor and power cable. To use this, you'll have to print the covers and servo housing from stylesuxx here:…
I designed this dual mosfet enclosure to mount underneath my Lack enclosure, using these mosfet boards I bought from Amazon: https://www.amazon.com/initeq-MOSFET-Printer-Controller-Current/dp/B073QGHTZL Of course it may fit other…
I plan to mount my Dasaki designed Ramps box underneath my enclosure. So I did this remix to add a flange and holes to accept a pin/bolt that locks the lid shut (so it won't fall from gravity). Category: 3D Printer Parts
I designed this "roof and filter kit" to harden the a mega+ramps enclosure against a cnc router environment. This kit is designed to fit the roomy and robust enclosure designed by iPa64. Here's the link in case you don't already have one:…
Updated source code: https://github.com/truglodite/3D-Printer-Enclosure I designed this for my Lack enclosure arduino control panel circuit featuring a 7.75" 2x20 IEE VFD. The model number of my VFD is 05464ASSY35119, but there are other…
I designed this 3 piece antenna mount for my TBS Sourceone v3 7" quad, but it may work on many other designs that use 5mm standoffs. It fits an ImmersionRC Ghost antenna. The 90mm mast has a 40degree rear tilt, and the antenna top has a…
These are all currently available results.
![Shopvac Hose Adapter Generator [Parametric]](https://media.printables.com/media/prints/322217/images/2782354_8da81c7b-012f-4dbe-a5bc-3735b8ff12a7/0329ca18c119e225468b09b64970899e_display_large_322217.jpg)
