Axial SCX10III Early Bronco Seat Back
I made these seat backs for when you flip the seat to fit a 6" driver. Flipping the seat makes the driver fit better but leaves the back open.
- Downloads
- 32
- Likes
- 3
- Rating
- 0
Counting matching models…
I made these seat backs for when you flip the seat to fit a 6" driver. Flipping the seat makes the driver fit better but leaves the back open.
* UPDATE: I made V2 with looser tolerances, V1 was a bit tight and needed too much sanding to fit. * UPDATE2: V3 further enhances strenght, more space for the foot bolt too. Length : 127mm Base : 17mm X 17mm Should be pretty perfect scale…
Armadillo off-road truck body for SCX10 III Hard body that has been designed to fit the SCX10 III Base Camp builder's kit chassis (AXI03011). The body might fit other 313mm chassis as well but the mounts need to modified accordingly.…
It's very close to the original and can be used as a template to create other parts.
Found this over at 3D warehouse, looks to be made by machfud. E. https://3dwarehouse.sketchup.com/model/4daea5e0-66f1-4aa2-acda-0a4cdee04284/SCX-10 Thought I would share it here as it is so useful to mock up parts. If the scale is wrong,…
This is a skid plate designed for the Axial SCX10. It has a flat bottom and counter sunk screws for high clearance and a pocket cut out for lighter weight and less filament/time when printed. Screw holes and counter-bores are according to…
20L Jerry Can
Want an overland style SCX10 iii Gladiator? You can now build one! The flat bed originally designed and printed for our SCX10 iii Gladiator Aussie Style Overland build . The flatbed comes with 2 different versions of an oversized, extra…
General description I was looking for a simple, flexible and affordable chassis for my many scale crawler projects. Nothing was optimal and I developed something myself. The chassis is based on the TFL-Racing carbon rails for the SCX10…
I made this toolbox specifically to fit the FCX18 FMS LC90 roof rack. Toolbox should be good for all 18 scale RC.
Wheel wells for FCX 18 - you'll need to perform a cut in the slicer and orient the flat parts to the build plate. Shock Keys, Rear keys are in 2 parts to make it easier to print. Front Shock keys I got lazy, just print the side with the…
Description General I have collected all SCX10 I & II parts i published on Printables so far. The chassis rails and skid of the SCX10 I are absolutely identical to those of the SCX10 II. So, many parts are suitable for both chassis.…
FMS FCX18 Toyota Land Cruiser 80 inner fenders with side steps. Print with tree supports due to the side step/rock slide part of the inner fender. Two screws are already present on the chassis to mount the inner fenders. The inner fenders…
I made this Cantilever Suspension to remove the rear shock towers so you can have more options for bodies on you Axial SCX-10. My Main goal was to use the stock shocks to keep the cost down. You will need to print the parts and purchase a…
Makes swapping batteries a lot simpler by keeping the body connected to the chassis. Uses the stock mounting points. Replaces the rear bumper mount and the mounting bracket connected to the roll cage on the body. 2 additional M3 holes are…
Center skid plate for the Axial SCX10 RC crawler. This gives you a little more ground clearance to prevent getting hung up. This skid plate DOES affect link geometry slightly. There are 2 version, once for the stock links using Axial…
Description: I designed these “Flex Blade” arms to get more travel out of the stock suspension when using the stock shocks. I have Treal 4 link arms installed, but it should work the same with the stock links. The mounting for the flex…
I found this on Cults and printed it using the SLS1S. It turned out really well except that the mounting pegs are just a few mm too narrow. I can still manage to mount it on my SCX10 Jeep but it gets tight. I also created a winch mounting…
This 32? Ford cab is designed by Ossum (you can find his design in the remix area.) I Basicaly squashed it down 20% to make it look more rat rod like. And some other adjustments to fit it on to a SCX10 frame. His work is amazing! Some day…
High Clearance front bumper compatible with the Axial SCX10 III Basecamp. Please note the bumper is NOT compatible with the JLU body or other bodys that use the “clipless” mounting system. Provides much improved approach angle vs the…
These sliders were perfect but they were too wide for the comp truck body so I made them smaller.
Whipped up a 40mm width mount for the nice front bumper farmersmark has made: https://www.thingiverse.com/thing:3531283 fits like a glove. I was lazy and you have to drill a hole through the smaller through-hole to attach the original…
Hey everyone, Here's some side trays/body mounts to install a RC4WD Xtra Cab body onto an Axial SCX10.2 chassis. Just slide some basic M3 nuts into the slots and you're ready to drop the body on. (You can either run the bolts like studs…
Normaly the bumper can print with the standard nozzle 0.4. But for good faces , you have to place it on the build plate in a angle from 39.50° . The tube was cutted in two part and print with a 0.2 nozzle. For the frontlight pls print…
If you want to use Losi Mini-T springs on your Capra or SCX10.3 shocks, these spring perches will allow you to make the conversion. The lower perch is designed to allow popping it off over the shock shaft without removing the rod end, so…
The stepfile is only the left side. Just mirror the side for the other. printed without support.
Axelstand for your rc crawler more specific Axial SCX10 III portal axels AR45P (AX1232022, AX232023). Can be used on front and back. Hardware 2x M3 x 8mm Cup screw 2x M3 nut For more info in swedish Buttyboys.se…
Normaly the bumper can print with the standard nozzle 0.4. Support is recommended.
Front : New version stronger and looking more like the orginal one. But still very short ! Rear : just the same with reinforcement. Print Settings Printer: anet A8 Rafts: No Supports: Yes Resolution: 0.2 Infill: 100 Notes: Printed on my…
-uses m3 screws -can be flipped upside down so the text is not visible -The pintle hitch mount is for this pintle hitch!! https://www.printables.com/model/279936-18-scale-110-scale-pintle-and-pintle-ball-combo-tr/files
Drew these up myself for ease of printing. STL is left and right. Same file is compatible with front and back. May require 180degree rotation in slicer to make it easier to print. Enjoy.
FMS FCX10 front bumper with an integrated mount. It features a winch plate mount, license plate mount, and towing shackle mount. Several variants are available: I suggest printing with supports to strengthen the chassis mount part (to…
These are rock sliders that can be installed on the Axial SCX10 iii Basecamp. I printed these from Prusament PLA as a prototype and have yet to break them. If they break, I plan to use some Prusament PC blend CF. You will need two M3x10…
Modeled this SCX10.2 flat skid to install a Vanquish VFD transmission basically as far forward as possible. Used this along with the Xtra Cab trays I also uploaded. Certain bodies may require some modifications to the body and/or the…
Scale accessory for Axial SCX10 III Jeep JLU Wrangler. Roof rack that can be mounted in the front, middle, or rear of the roof. There are two mounting options: either using double-sided adhesive tape or by screwing it directly through the…
This is a front bumper that allows for good approach angle and has a much narrower profile then the original. My front bumper kept getting caught on the tires, so I designed this. I used PETG-CF as the main material and used PLA for…
A wedge to raise the motor up away from the rails when using a HobbyWing Fusion with GSpeed skid plate and chassis rails. The opo named files tilt the transmission side to side while the other files tilt the transmission front to back.…
PLA for indoor use. 2 or 3 walls depending on nozzle diameter, 20% to 24% your favorite infill. No Supports Required (4ea Required) Saw Horse Stand Vertical Piece (2ea Required) Saw Horse Stand Horizontal Piece (8ea Required) 3mm x 10mm…
I tweaked the original so it would line up better on the SCX10 II, then replaced the stinger with a bull bar and tweaked the bumper to fit the frame more closely and allow better approach angle. TinkerCAD for front bumper:…
downsized frame from scx10 to scx24 . skid plate included I used and battery/ESC/receiver tray I put together.
So this is my first part for the FCX18 K10. In this case there will follow some more.
STL VERSION RELEASED! - It is time (after 2+ years) for this model to be freed from my Patreon I grouped the three handle versions together because I couldn't stop them from laying on their side in the slicing software and it's a pain to…
Made this for modeling up RC Crawlers, Not sure how accurate the motor mount is I think the motor sits several mm too low, but it all seems close enough to me. Found a better picture for the motor mount, I expect everything is accurate to…
Looking for a clean, adjustable, and fully compatible battery tray solution for your Axial SCX10 III Coyote ? This tray is a drop-in alternative to the original Axial AXI-2999 battery tray , offering flexibility without compromises. Key…
This is a new roof rack that uses the same mounts as my previous model. The idea is that you can replace the roof rack without having to modify the mounts if you have drilled and screwed them into the car body. Link to previous model:…
Here is my version of a simple toolbox for the fcx18 K10. Printed with a 0.4mm nozzle,heights of 0.16 or 0.12. Filament could be a silver silk one. Top parts must be glued.
Fits Axial 1.9 bead lock wheels. Category: R/C Vehicles
This model is a front bumper for the FCX18 K10 and can be installed using the original hardware. I printed it in PETG-CF, but any material should work. I used a 0.4 mm nozzle, 0.2 mm layer height, 3 perimeters, and 15% infill. There are…
Habe mir zwei Rock Slider erstellt. Abgestimmt auf den Jeep Cherokee von Axial (SCX10). Vorteil: man kann die Karosserie in den Rock Slider klemmen und die Seitenschweller in der Breite einstellen. Karo klappert nicht so, einstellbare…
I play a little with the thinkercat and designed a body for an Axial SCX10
A simple front bumper for a SCX10, have not tried it on a SCX10-2 as of now. You can print it without supports but it may not be optimal for the end quality. There are also holes for 2x 5mm leds.
Rings for the beadlocks can be found here https://www.printables.com/model/744137-bead-lock-ring-for-axial-scx10 https://www.printables.com/model/744136-axial-scx10-bead-lock-spyder-lock-19 1.9 Beadlock wheel for R/C car 12mm hex
Secure mount for a battery in the front of the SCX10. Uses 4x M3 screws. Sized for a 5000mAh box LiPo. I can alter the size for different batteries, just shoot me a message. The Basecamp body still fits in this configuration but I can't…
This is a full back of cab for a RC4WD Mojave body and Skids that will work on an SCX10 ii or similar to mound the cab using screws there are optional brackets to mount the back using screws or you can just glue in place.
I designed this piece to work with my trans and motor flip mounts for a 10.2 kit chassis. Steering servo in stock position and a servo winch flat and as low as can fit up front on the chassis. You may have to space your servo up depending…
AXIAL SCX10 Ball Joint nozzle 0.25 or smaller
Simple trailer hitch that fits the standard rear bar on the FMS fcx18 Lc80. A 5mm ball joint fits snug over the ball.
Chassis kit: https://www.axialadventure.com/product/1-10-scx10-ii-4wd-raw-builders-kit-v2/AXI90104V2.html Body kit: https://store.rc4wd.com/RC4WD-1985-Toyota-4Runner-Hard-Body-Complete-Set_p_7220.html The rear hinge comes in 2 parts. Use…
Narrower wheel wells and lower rear shock keys for V2 body. You will have to reroute the wiring for the rear lights. The rock sliders are from here: https://www.thingiverse.com/thing:7247724 Edit: I updated the rear shock keys with the…
Motor flip mount for the original scx10 transmission, A little bit thicker in design then my 10.2 style flip mount but otherwise a similar design. Should also fit 10-14 pinion, maybe a bit more and a bit less. I also mirrored my trans…
Simple 1:10 Toolbox for scale RCs. Category: R/C Vehicles
Flip your 10 ii kit transmission and motor forwards for the best cg! The motor flip mount fits a good range of pinions, 10-14 at least, maybe a bit lower and higher. The motor mount is pretty solid as long as you print it pretty thick, 5+…
Remix of SCX10.2 shock front hoops by justicedspencer This is the V1.0 of shock hoops for the SCX10 2 that allows for near 1:1 motion ratio and scale angle shocks (straight up and down, not angled) and allows for long shock travel while…
FMS FCX18/FCX24 Wall Mount – Because Your Floor Isn’t a Garage Sick of tripping over your crawler and transmitter? Hang that beast on the wall like the trophy it is. This simple 3D print keeps your RC life tidy and your significant other…
Designed for the Littleguyracingparts Super 8 axles, which means anything with an wheel to wheel of up to 13.5cm. Stock width is like 9.5cm. Works with stock axles, stock axles+hex extenders, Meus isos, Lgrp super 8s axles without hex…
general description The chassis geometry is 100% identical to the original RC4WD Trailfinder 2 (11.2"). All mounting points, bumper mounts, body mounts, shock mounts, and leaf spring hangers are 100% RC4WD compatible. The Gearbox. Only…
Battery tray to take the big hard case 5200mah 3S lipo batteries, mounts to the original tray mounting points on the right hand side, made it as low as possible without cutting original splash guard, 3mm walls, print with supports.
Add magnets to your GCM Racing J2 Skeleton Chassis with China JK body for quick and easy removal. Holds great. I also added an area for the on/off switch to go. Can be trimmed if not needed. You will need to drill 4 holes in your chassis…
Rings for the beadlocks can be found here https://www.printables.com/model/744137-bead-lock-ring-for-axial-scx10 https://www.printables.com/model/744136-axial-scx10-bead-lock-spyder-lock-19 1.9 Beadlock wheel for 12mm hex R/C vehicle.
Shock extensions based on aluminum aftermarket ones. 3 files are included - the specific setup I have for front and rear, and a universal one for more adjustment options. You will need 2x M3x10 screws for each extension, so 8 total if…
Fits Axial's 1.9 bead lock wheel. PoisonSpyderRings_V2_1_fixed: recessed holes for screw heads, larger inner circle. PoisonSpyderRings_2: standard bead lock, smaller inner circle. Category: R/C Vehicles
Being the sucker I am, I spent too much money on a vacuum to only have it break within a couple of weeks of owning it. This model replaces it with something that requires much less parts and has been more reliable. Print Parameters:…
this link works great with the ball bearing that you can find on printables if you type in scx10 all my links that are 1/10th uses them and in the hole with minimal filing. Printed in PLA then PETG 100% Enjoy! MRC
2025 06 25 : News : i've added a full 3 links set : the C-hub and the panhard bar support, see pictures. Beware : to have no bump steer the panhard and servo link need to be the same length and to be parallel. Use the v3 and the servo…
Imported from my designs on Thingiverse. Original upload was 18.07.2019 (dd.mm.yyyy) I do most mechanical design. Can do easy basic patching. Mount/bracket for your "CNC Black Aluminium Transfer Case" with mostly 2:1 gear ratio. It has…
This parts are detail for FCX18 K10 frontgrill. Look at picture of the positioning. Parts will be print with a 0.2 mm nozzle. Parts must be glued in the original grill.
Easy to print may require a small amount of filing to fit the ball joint in. Have fun! MRC.
FMS FCX18 Toyota Land Cruiser 80 Inner fenders with side steps + display stand This model is designed for the FMS FCX18 Toyota Land Cruiser 80 version with removable fenders . The set includes: Inner fenders with integrated side steps /…
WORK IN PROGRESS. Just want to share. 1.9 Bead Lock Wheel Split into two pieces, thus no support required. However (5) M3x6mm screws are required to secure the back to the front. (12) M2x10mm for the rings. Rings for the wheel can be…
These are bumper brackets for the Axial SCX10. Made these so that I could extend both the front and back to fit a new body. Also added stabilizers to use towards the battery holder as I had to move mine to the front. The battery holders…
This adapter will fit RC4WD 1/10 scale Warn winch to the RC DC front bumper for an Axial SCX10. I will download the RC DC front bumper file and give credit in a separate model profile.
1.9 Beadlock wheel 12mm hex. Uses Vanquish Products SLW style hub to mouth to hex. Modeled to match my Full size truck wheels. The file ending with BIS has a support structure already built up to support the print Category: R/C Vehicles
general I often build crawlers with third-party links, custom links, and other rodends, and I always have problems getting the links to the exact right length. That's exactly what these tools are for. Currently only available for the TRX4…
8 hole beadlock wheel for 12mm hex RC vehicle. Split into two pieces, thus no support required. However (5) M3x6mm screws are required to secure the back to the front. (12) M2x10mm for the rings. Rings for the wheel can be found here:…
I wanted to be able to mount a Tamiya f350 body on my axial based 6x6. So I came up with a factory ish option to be able to mount it. Bolts on just the same as axial sliders and has side screws for the Tamiya holes. You can also use long…
Axial SCX10 Shock Seals The SCX10 factory shocks are well known for their terrible leaking. I've tried a very simple approach at fixing this issue by replacing the spacers beween the O-rings at the shock body bottom. After this simple…
Need 6mm OD aluminum tubing. Cut to taste and glue (cyano should do the trick). Should also work with the FCX10 K5 provided you print a mirrored one for the driver-side.
an upgrade to Ascender body mounts for SCX10 II https://www.thingiverse.com/thing:3210534 These should be more universal to different lengths of bodies. part A screws to part B, separated for strength. Bumpers can be found here…
battery tray mounted in the front and center I printed mine in ABS, but really anything would work. I printed it with the small closed end on the bed seems to work well. You will need longer m3 bolts
Front motor mount for injora gearbox , others should fit. Needs M3 square nuts and m3 screws. Transfer case, use parts from the SCX10 gearbox ( bearings and gears ) . M3 x 30 screws and nylocks. Grease if you want. It slows the rig down…
Mine developped a crack and was floppy. Here's a replacement with and with tow hitch mount. Used an existing bumper mount as a base but can't found it back, sorry. 15-08 : added reinforced mounts (v2)
This is a front bumper / grill for an scx10 hot rod build. it includes a servo mount under the grill. I haven't printed it yet to know how well it fits, but it should be good. There is a pretty good remix of this over here…
A roll cage style bar that sits inside of the lexan of the windshield on the Axial Scx10.3 CJ7. descrete and provides ample protection to keep your widnshield form getting caught on rocks and ripped off. made because my friend and i have…
Print in TPU. Glue to the rear lip of the rear inner fenders.
My kids have a bunch of the Bruder brand toys including the big lowbed trailer. I thought it would be fun to tow it with my Axial SCX10 RC truck. I wanted something simple that bolted on easily. I found someone had already designed the…
SCX10 II style transmission skid plate available in three different versions. One has built in mounting tabs for the rear upper links which can conflict with some longer motors. The second has no tabs and will require the use of a nut to…
Эту модель я сделал, чтобы переместить бампер ближе к кузову, так модель выглядит лучше, а также улучшает внедорожные качества. Для печати я использовал abs gf. Но вы также можете использовать abs/petg. Для большей прочности используйте…
This is an add-on for body post/mounts if you printed my remixed long travel shock mounts/hoops ( https://www.printables.com/model/730892-long-travel-shock-mounts-for-axial-scx10-2 ) These just bolt onto the inside of the shock mount.…