NZXT Phantom 410 power button
This is a replacement power button for the NZXT Phantom 410 case.
- Downloads
- 189
- Likes
- 1
- Rating
- 0
123 models
This is a replacement power button for the NZXT Phantom 410 case.
This is my take on the NZXT "Puck" style cable organizer. This is designed to coil a headphone cable or VR headset tether inside the channel and hang the headset or headphones over the outside of the cube. Print instructions This print…
Comes in 4 pieces, split STL to objects in prusa slicer. There's a 0.5mm gap between parts; mask back panel, snap pieces into back panel, and fill gaps w/ JB-Weld or similar. This is to allow everything to fit on the bed and account for…
As printed by hundreds of H1 owners on Reddit, I present the: Triple & Dual 40mm Exhaust Fan Shrouds for NZXT H1 Case - Version 4.0 Benefits: Typically a 6 degree Celsius drop on RTX series GPUS with three fan version Additional 2-6…
My friend needed extra HDD/SSD trays, as his (bought used) NZXT H440 computer case only came with one. So, I measured the original and made this to fit the tray slots in the case. Fits both 2.5" and 3.5" disks. It's available in three…
My GPU was suffocating inside my H510 Elite, so I created a front and side panel for better airflow. Air filters coming soon.
printed in TPU, the softer the better, ninjaflex is a good choice, i did make the gormmets pretty “thick” its still not %100 but its pretty damn close
I wanted a bracket so I could mount fans in the back of my NZXT H1 case without them being visible while still being able to use the exiting back panel. Since I couldn't find anything quite what I wanted I designed my own. This should…
NZXT cases have a unique and clean look. But most of them, including the H210, have bad airflow with the stock front panel. This model solves this issue and will make your PC breathe a ton of fresh air ! It fit perfectly on the case just…
NZXT H7 COVER BOTTOM FRONT
Update: *2021-01-09 : Added 10mm, 25mm, and 29mm spacers with a different socket configuration (labeled mk II). This new configuration might work better depending on your printer tolerances. The 29mm spacer gives more room for fans on the…
Holder anti-sag for RTX 4070 Gaming OC Gigabyte graphics card to prevent pcb cracking issues or especially when the PC is being transported. Printed on X1C Bambu lab, no support, 0.20, 3 walls, 25% Gyroide density. You'll need two M3x5mm…
A sleek version of Daymo's NZXT Kraken Cable Comb (3580218). Slimmed it and added chamfers, designed with 0 tolerance sand/file/scale tongue to fit. at some point I'll return and mark it as an actual remix once thingiverse works again.…
These models are not mine I just uploaded it to printables because I thought others might search for something like this. Notes from the creator: I use superglue to assemble ill add a picture so you can see where everything goes I use…
An airduct/scoop to fill up the hole in the NZXT H7 Flow. The scoop directs the air from the front fans towards the GPU. This duct is specifically designed to work with 140mm fans. It bolts through the air duct into the 140mm fan as shown…
Moved one of the included 120mm NZXT fans from the h510 case to the bottom. Designed this adapter so it can lock into the holes at the bottom of the interior. They pressure fit into place (for removal I recommend pushing from underneath…
Just a simple logo swap from Corsair ship logo to NZXT text logo.
⚠ Warning ⚠ This model's lower part height is either slightly off or the print has warped during printing. If i would be doing this for the second time I would check split this into 4 parts instead of 2 and measure pin distances. Bottom…
Not sure exactly how this idea came to my mind, but hexagons look cool and I thought why not design some that click into the front of my PC case! The designs and colors you can add to the front of your PC are limited only by your…
I recently built a computer in an NZXT H210 mITX case and it has a spot for a single 3.5" HDD on the bottom. The room in the case allows for another 3.5" HDD on top of it without any clearance issues. I would imagine this would work in…
Feet extension for NZXT H510 case. No specific print instructions required, i did mine at 100% and PETG for strength and heat resistance.
Supporting the Gigabyte 4090 Gaming OC in the NZXT H7 Flow is tricky. The support that came with the GPU did not fit in this case because of the cable cover. I used the 2 threaded extrusions that hold a cable tray on the back of a case to…
I designed this bracket to be able to install a 3.5" HDD drive in addition to one 2.5" SSD into my NZXT H1 v1 PC case. Just remove the original 2x SSD bracket and use my bracket instead. You will need some 90° angeled SATA connectors to…
The magnets used are 6mm X 1mm Printed face down and superglue together I have added the f3d,step and 3mf files Hope it helps
This is a replacement front panel for the H510 Elite from NZXT. This is a great case, and a cheap case at that! The single biggest issue is the entire front of the case is a glass panel. Read entire Instructions to see DIY steps, don't…
i designed a front panel for the NZXT H400 and H400i. It mounts on the existing bracket that hold the original metal panel to the case. You will have to cut the opening on the bracket, i used a dremel (see pic 2) PS: it's my first model…
I needed a second tray for my NZXT 710 case but it'll probably work with other NZXT cases. I this should snap in without the need for the screw but it does have a hole for it. I would recommend screwing it down if you're using an HDD but…
I found these hilarious feet models for a PC tower by pacypo and began making some. Then it dawned on me that I recently bought some TPU as I just got a new direct drive Neptune 4 printer (awesome printer BTW, would highly recommend) and…
Simple tube comb for NZXT Kraken AIO with 11 mm tube diameter.
Printing recommendations Print with 0.2mm or 0.3mm layer height and at least 3 walls and 4 or 5 top and bottom layers. I recommend at least 30% infill. After printing remove the slots support wall (integrated in the design) as shown in…
I noticed that the PCIe slot cover on my NZXT H510 Flow PC Case did not sit flush with the case so I'm using this model instead. The .3mf file contains four variations of the cover. There is a solid cover and three patterned/mesh covers…
Elevate your NZXT H1 V2 gaming experience with this custom-designed PSU replacement cover! This innovative 3D-printed accessory not only replaces the original PSU cover but also adds functionality and aesthetics to your build. With this…
Replacement fan grill for NZXT H1 radiator fan or really any 140mm fan. Just in case you accidentally send yours back to NZXT during RMA.
Printed in PLA at 0.12 and worked well
Anti sag brace for the NZXT H700/H700i
Inspired by some of the LCD mods on Reddit/SFFPC for the NZXT, I gave this LCD mod a crack and it worked out pretty well. You need the 3 prints.. one's the back plate, and two brackets to hold the screen in place. The screen i used was…
Foot for NZXT H-series case. Has recess for existing rubber mat. Modelled in Fusion360. Prints without supports.
There are two versions. With and without LED lighting. For all common keyboard switches
It's apapter for holding NZXT Kraken cooling system for NZXT H510 PC case when You lost or broke original holder plate Printed without supports, 0,2mm layer height, PLA probably PET-G would be better for heat resistance
Designed a GPU bracket that attaches inside the NZXT h510. It locks in behind the cable cover. This is originally designed for the Aorus Master 3070ti, a very large GPU. Feel free to remix as needed.
Just a simple replacement bracket for the NZXT H440 case. I saw that someone was needing one over on Reddit/hardwareswap and I have an H440 readily available so I figured it would be great practice modeling plus it is always nice to add…
Print in PET(G) or ABS/ASA for heat resistance. This specific chassis gets hot; feel the glass after a bench! Normal settings otherwise. Hope this helps someone!
Gaze not too long into the void, for you will inevitably think to yourself: “Man…I could fit another couple terabytes in there.” To remove the NZXT's front frame, you may have to use a pair of needlenose pliers to flatten the tabs on the…
I was fixing up my old computer for a friend and found that the buttons had all degraded, so I decided to model some replacements. These worked for me with no binding and smooth movement. To print: !!See photo for orientation!!. You will…
NZXT Kraken X60 AM4-Adapter To use the old watercooling AIO, I had to design a bracket to mount it to an AM4-socket. The original backplate and screws are reused. Use a 7mm drill to widen up the holes until you get a snug fit. printed in…
Inspired by this GPU support but the designs are so different I didn't end up calling this a remix. This is a GPU support bracket for an NZXT H700i or NZXT H700 case. It fits my GTX 1080ti Founders Edition, which means it should also fit…
RaspberryPi case that looks like the NZXT H510. Use a small piece of plexiglass or clear plastic for the side panel. Compatible with some heat pipe with fan coolers out there. Use a 16mm Pushbutton switch for the power button.
I needed to fit my H5 Flow case into a lower height cabinet, so I modeled some shorter feet. They fit really well, snap into place and then you can screw them in. STL foot is 7 mm high. I included a F3D file, so you can very easily change…
This is a remix of another adapter for the NZXT H510 that will make it easier to mount fans on the bottom of the case for better gpu airflow. In the remix I just duplicated it and merged 2 sides together so that you can fit 2 fans. One of…
I made a hook that holds my headphones that clips on the front face plate of the NZXT H440 Print instructions Category: Audio Summary I made a hook that holds my headphones that clips on the front face plate of the NZXT H440
SSD Bracket to add more hard drives to a NZXT M59 Case. You will need to print x2 Brackets and 4 screws per SSD/HDD. The locking tabs don't quite lock in 100% but it fits perfectly and snugly fits a typical SSD/HDD in the bracket. Print…
I wanted to add more drives to my NAS but keep using my old cast-off H440 case. Since the drives mounts are spread far enough apart in the original design it's actually possible to fit two 3.5" drives in 4 of the 5 original mounting…
Front grill for NZXT H1 V1. I'm not sure about V2. Set top 0, bottom 0 layer and chose the infill patten you like for the grill. You can print them all at once or print separately like mine and stick them together using superglue. Double…
The base is slightly beveled so that the disks hang vertically and thereby leave as much space as possible from the PSU. The SATA cable can be conveniently hidden there. Disks can fit behind the cover even with a straight end of the SATA…
This is a drop in replacement that allows an NZXT Kraken watercooler to be converted to a standard BSP G1/4 water cooling loop. Just swap the O-rings and screws from the original 3/8in barbfittings. Not sure how this needs to be printed,…
A cover I made to hide the cables of the NZXT Kraken x72 cpu cooler.
NZXT PCI Slot Cover should work with others models too.
My computers live underneath the corner of an L-shaped desk, so I always like to replace their feet with casters to make it easier to access ports, etc. I printed these in nylon (Taulman3D Alloy 910, black) for strength/impact resistance,…
Haken um Kabel am Tower zu befestigen. Die Haken passen in das Lochgitter vom NZXT H710 Case.
Remix of a NZXT 510 Case for Raspberry Pi 3 Model B. Changes only to the outside part. I printed mine in PETG but PLA is probably fine too. Use brim. Optional rubber feet, print in TPU. Currently working on a fully own NZXT 510 case for…
For my custom loop NZXT H1 V2 I designed some parts: Backpanel for 240mm Radiator + Fans Pump Bracket for EK Classic 160 Foot with Base and Diffusor
MOAR AIRFLOW FILTRATION If you Feel like you are choking your NZXT H7 Elite because you put a Toaster in your PC blowing with absolutely no Airflow, This Will Help you get Airflow and Keep Esthetics as well! This includes An Air Filter…
Fan Cover for 140mm NZXT H510 computer case. It has no functionality, I made this because I didn't like the original design from case. Use the original screws from the manufacturer.
The bar has the following Japanese proverb "Fall down 7 times stand up 8" embossed on the upper part. Printed it with brim and laying it down on its thin side, with organic supports. Added split parts for smaller printers
An updated version of my previous design. Easier printing , better finish of the front side, less support needed and stronger too. The previous version had some issues with deformation over time. I have this version for 2 years and with…
The arrows are for orientation, it goes on the inside of the case. Iron for a nicer look.
Remix of Supahobnobba's O11D XL fan duct to fit the NZXT H9 Flow 2023 side fans, simply changed Z height and enlarged screw holes for easier mounting
Over time the original injection molded plastic clip just got brittle and fell apart. After a quick search I saw there was no replacement readily available to print, so I made one. Printed in PETG on a 45° angle for additional strength.…
This was designed to replace my old model. This design in more durable, better looking, and fully customizable. Throwing out old things that work is dumb, and I've seen at least 5 of these cases being sold used specifically because of the…
This is a wall mount for NZXT H510 Elite, but I think it will fit other NZXT cases to. Mount is 215 mm wide. Print Settings Printer Brand: Creality Printer: CR-10S Rafts: No Supports: No Resolution: 0.24 Infill: 40+ Filament: 3de PLA Max…
A bracket to allow you to use a X63 AIO on the AMD BC 250 ex-mining card, use ABS/ASA. Requires 4 1mmx8mmx15mm springs.
Basic replacement leg for the NZXT PC case. Printed at 15% infill. I used 0.6 nozzle and printed at 0.3 but should work fine with your standard settings.
Simple really, this is a straight replacement model for the existing PSU Cover. Mod to your delight. Fusion 360 model included. Drop me a comment or a rating if you like this!
just a remix. print with the pegs facing up.
NZXT Kraken X61 AM4 bracket. 3D printed and working well for me.
A two-part headphones/headset holder designed around the NZXT H510 PC case, although this part will work with similar cases that have 25 mm tall feet. Only requires one 20 mm countersunk magnet, unlike my other design. The holder tucks…
lost my bracket for my ssd made this does the job
a support for my vertically mounted Gigabyte RTX 3080 OC, which is mounted using a cooler master V2 universal vertical GPU bracket, the holes slot into the base of the case like lego. Category: Other
This is a mini-computer model that harnesses all of the basic ideas of building a Pc. This can be used for teaching purposes or simply for enjoyment. This model helps you enjoy creating a pc without any of the little details or the cable…
Similar to my EKWB pump / res combo holder: https://www.printables.com/model/291904-ek-pump-holder-for-nzxt-cases This mounts the Alphacool Eisstation to the vertical bar inside NZXT's PC cases.
Made this to use with my NZXT computer case since the magnets that I was able to find weren't strong enough to hold the headphones. Created in Autodesk Inventor, added .step file if you would like to modify it.
Headphone hanger for NZXT S340. Fits on the front air intake.
This mount is for NZXT H1 V1. It probably won’t fit V2 of this case. Installation is pretty straightforward. The only thing that you will need is additional SATA power cables for your PSU since NZXT only provides a single SATA power cable…
The Smart Device V2 comes preinstalled with the NZXT H510i and some other cases as well. The new NZXT RGB & Fan Controller doesn't have the same dimensions. It comes with magnets and Velcro to mount it in the case, however I didn't like…
This piece replaces the original cable shroud cover in the NZXT H7 Flow (2024) for better clearance. All screw and hardware mounts are the exact dimensions of the original. Print in 2 pieces A+B are needed, also comes with an extended…
This custom remix was created with the goal of improving cooling performance for my PC without needing to overhaul my case or break the bank . My cooling setup was already decent, but I wanted something more efficient. After searching for…
This adaptor plate allows you to mount an EK-Quantum Kinetic TBE 200 D5 (or similar) PC Water Cooling pump to the removable bar of NZXT's cases that have the vertical cable management bar. As seen in the picture, this allows the pump/res…
Was moving around my workstation and somehow lost one of the foot pads. Rather than rip the others off and let it go, I ripped off the rest and made replacements. I used some double-sided tape to stick them on, but I'm sure you could add…
Uchwyt anti-sag do karty graficznej Gigabyte GeForce RTX 4070 AERO OC, zaprojektowany w celu zapobiegania wyginaniu PCB pod ciężarem chłodzenia, szczególnie podczas transportu komputera. Wydruk wykonano na drukarce Creality Ender-3 V3 SE,…
Power Light Diffuser to cut the glare on NZXT 510 PC Case and may fit others, I got tired of the glare and flickering of the power button led as it blinks with drive activity. Orientation should be automatic with 4 top/bottom and 2 walls,…
Cover for the grafics card calbe hole of a NZXT S340. With and without the p. Print Settings Printer: CTC Bizer Dual Rafts: Doesn't Matter Supports: Yes Resolution: 0,2 Infill: 10% Category: Computer
Made a mount for Waveshare 5' display . It can be mounted instead of the SSD holder on the side of the PSU shroud. The cables for the display should be routed under the cable bar.
Hey guys, this is my very first thing I created on my own. I hate it when my graphics card bend to the bottom because its too heavy. So I created this graphics card holder to hold it right in the way. This holder ist designed for the NZXT…
This headphone hook sits on the front panel. It doesn't conflict with the front panel filter. Print as is. No need for supports. Perimeter: 2 Layer Height: 0.2mm
Decorative plate to modify your side panel and fan grill. Custome inserts could be made for your own design too. Required Parts 9 - 6x2 magnets
A low-profile hook that press-fits into an NZXT Puck (magnetic cable management device) for hanging IEMs or other smaller items. Printed in ~25 min with 12% infill. You could boost your holding force with a magnet in the base, but it…