327 models
Thread Gauge Tester: A Handy Tool for Measuring NPT Hydraulic Pipe Threads Looking for BSPP thread testers? You can find them HERE! November 10, 2024 Update: Added tester variants with a tab for easy organization on a ring, cord, or zip…
Print approx. €2.18–€2.66 excl. taxPreliminary estimate for one variant
After stubbornly refusing to make the attempt, I finally succeeded in modeling ¾ inch NPT threads. This model can server as a plug for a ¾ inch PVC threaded female adapter. But it is generally useless on its own. What it does represent,…
Print approx. €0.46–€0.57 excl. taxPreliminary estimate for PETGSource material: PET
Thanks a lot to @Noname_Engineer for that great GoPro tripod model. I was too lazy to go out to a hardware store and buy thread parts. And I also needed a trippod mount very quickly (stores were closed). Because of that I just added the…
Print approx. €0.75–€0.91 excl. taxPreliminary estimate for PETGSource material: PET
I needed several inch threads for building waterpipe adapters in Freecad. They should be printed in PETG. The tools in the Fastener workbench did not have the correct pitches and tolerances. Here are some substraction bodies with a…
Print approx. €0.90–€1.10 excl. taxPreliminary estimate for PETGSource material: PET
Spool threads box. Hello, I am sharing my own idea of box, which can help in storing threads spools. Total size is around 17,2 cm x 17,2 cm x 8,6 cm. It can hold up to 36 spools. I've printed this one with 2 layers and 10% of gyroid infill.
Print approx. €2.05–€2.51 excl. taxPreliminary estimate for one variant
Hammerkopfmutter T-Nut Mutter mit M4 Gewinde für 30x30 Aluminumprofile Nut / Slot / Series / U 6
Print approx. €0.25–€0.31 excl. taxPreliminary estimate for one variant
Chick waterer made for the powerade zero triple thread bottle. Fills up about halfway in the bowl. There is also an anti drown model that should work good for quail chicks. But there are three sizes to fit any need! I made a holder with a…
Print approx. €0.94–€1.15 excl. taxPreliminary estimate for PETGSource material: PET
3/4-14 NPS (National Pipe Straight threads) Funnel. Made for most steel drums with these threads. Will take coffee filter is so desired to filter the oil. (I use it to check for contaminants.) https://a.co/d/caqnBdN Added coffee filter…
Print approx. €2.17–€2.65 excl. taxPreliminary estimate for PETGSource material: PET
Same as original but the top is altered to have a PC4M10 adapter thread with 1mm threads with a PTFE tube stop just below. The filament hole is 3.5mm with a chamfered lower exit hole. This positions the filament exit from the PTFE tube is…
Print approx. €1.33–€1.62 excl. taxPreliminary estimate for PETGSource material: PET
Less than 10 percent of people who download an item click the “like” button. Be the 10 percent. Click the “like” button and show your support. If you find this model useful, feel free to buy me a coffee . After much trial and error, I…
3D Printable Screw Generator for Fusion 360 This is a fully editable Fusion 360 file designed to generate screws specifically optimized for 3D printing. Most standard metric threads are designed for metal manufacturing, not for FDM…
I found a high number of measuring tools for metric screws. But what about a measuring tool for inch screws, nuts and wrenches? I couldn't find any, so I created one, or better two :-) The tool is created for UNC and UNF threads and…
These screws are inspired by ISO 8765 metric screws but they have standard pitch threads . They come with hexagonal heads, that are slightly bevelled on one side and contain a washer-like elevation on the other side. The longer screws…
There's a model for a 48mm thread (usually from European 5-6l bottles) and for a 28mm thread (ex. Coca Cola bottle). Using a 48mm thread is recommended because the seeds don't get stuck Poke a small hole in the center at the bottom of the…
Perfect for temporarily sealing hydraulic, pneumatic, or other system components during construction or maintenance, protecting against dust and debris. This design has been thoroughly tested in real-world applications, ensuring excellent…
I have been asked to create a measuring tool similar to my “Inch Measuring Tool” https://www.printables.com/de/model/345844-inch-measuring-tool-for-screws-nuts-bolt-heads-wre So here it is! The dimensions are based on ISO DIN 13. (I will…
Expands as screw is inserted to keep it snug in the drywall. No supports needed. Recommend printing at <0.20mm layer height.
Thread Gauge Tester: A Handy Tool for Measuring Hydraulic Pipe Threads Looking for NPT thread testers? You can find them HERE! ***Smaller Size UPDATE*** (July 18, 2024) Added the following measurements: 1/4 inch, 1/8 inch Product…
Fully printable T-nut for 3030 aluminum extrusions such as those found on the Prusa Mk3/Mk3S. Available in M3, M4, and M5 printed-in threads. Can handle light duty work as long as you're not hamfisted and over-tighten it. I've used these…
4040 T-Slot Nuts RV2 Series - M3 M4 M5 M6 Threads Suitable for: 09/05/2026 Update: Added Flat Version 04/06/2026 Update: geometries cleanup ***Warning: Dimensional Tolerance Notice*** This connector is designed for our standard profile…
General Note - This was tested on the Anycubic Kobra (regular/standard). This does not fit the Anycubic Kobra Max. I really liked the idea of storing nozzles in the aluminum V-Slot but I didn't really have any m6 nuts available to keep…
I couldn't find a suitable free tracer housing for my Airsoft guns so I designed my own. It fits an xcortech tracer down the end, so you can have extra barrel length inside the suppressor if needed. I added some electrical tape around the…
This is v4 of my print-in-place DnD dice storage box. The design stores a standard set of seven dice and I've user tested the pictured green model for 2+ years filled with heavy metal dice, so even in PLA it is a robust and proven design.…
Original description by Iker Libano | KNIN Custom , copied and adjusted to the FreeCAD version (changes in Italics): Update: The generator was designed in FreeCAD 1.1.1, therefore FreeCAD 1.1.1 or later should be used when using the…
harlot mod Category: Sport & Outdoors
I had the idea to extract the negative thread from a Fusion 360 model as a part that can then be used in your slicer to add a thread to a model without the need for CAD. To do this simply use Add negative volume. load… Position the thread…
3030 T-Slot Nuts - Collection - M4 M5 M6 Threads Suitable for: All our designs are free to download and use. Your support fuels our creativity, if you download/enjoyed this file, please leave a like. Thanks ***Warning: Dimensional…
Note: This was remixed from a model on Thingiverse and is now imported here. I saw on my Ender 3 V2 that I had screw holes that was intended for Creality's new BLTouch kit. I really like the mounts from prydonian and puturai, but both…
Following this schematic for canning jars I found I created male and female thread profiles for wide mouth and regular mouth canning jars. STL and Fusion 360 files are included. Also included a simple lid for both regular and wide jars.
I am told there is no standard for paint pole threads, but this fits the two paint poles and the broom handle that I have. This is just a threaded cylinder to use as a starting point for your model. I am including the .stl file and the…
This winder is a little more Versatile than other iterations, subjectively. It uses M5x0.8 Threads to allow each dipole post more secure into the winder. SO239, space for a T140-43 or smaller Toroid for a Choke. Pictured is the dipole as…
This cable mount for 6mm cables is based on the model by VC design, but easier to print and a bit more sturdy. I added a double mount for nicer double wires. Added a cap that pinches the wire so you can get nice straight runs.
GL threads are commonly used on glass laboratory apparatus. This GL thread parameters are optimized for vertical printing on MK3S/+. The threads on glass bottles with GL80 threaded necks are not the same for all manufacturers. For…
Quick model to make it more convenient to fill water balloons for the kids. It's a nozzle that fits standard garden hose threads (NH-11.5, female). The model has a 40mm long nozzle (easy to grip) with an OD of 10mm and an ID of 4mm. Even…
Update: new option for an infinitely adjustable moving jaw added! no need for the series of holes. The version included only works with a nominal 1x3" (actual dimensions 0.75inx2.5in- 19mmx60mm) Model files for this jaw are included in…
A basic 6 inch (150mm) long tripod extension with 1/4-20 thread at both ends. Diameter is 1 inch (25mm).. simply screw onto you tripod to add 6 inches.. This is perfect for a short tripod that just needs a little more height to get your…
Here are two shift knob designs with most common thread pitches to choose from: M12 x 1,25 M12 x 1,5 M10 x 1,25 M10 x 1,5 Knob sizes: Knob1: lenght 80mm, diameter 40mm, thread depth 40mm Knob2: lenght 90mm, diameter 40mm, thread depth…
Modified fs-cover for mk3s with threads for bowden
These screws are inspired by DIN 921 metric flat head allen screws. As I could not find standard dimensions for some of the rarely used screw variants, I decided to complete them with best guess estimations. The longer screws have partial…
Complete set of metric fine pitch nuts inspired by ISO 261 and ISO 262. The improved thread design does not require consideration of printer tolerances any longer - at least as far as the nuts are big eough for the printer. Print with low…
Description: In spaces where every inch matters, the Compact 90-Degree Bent Pipe with 1 1/2 BSP Threads takes center stage. This 3D-printable model is tailor-made for applications like water pumps in tight confines, providing a…
print with brim for better adhesion
These screws are inspired by ISO 8765 metric screws and they have metric fine pitch threads . They come with hexagonal heads, that are slightly bevelled on one side and contain a washer-like elevation on the other side. The longer screws…
This is a quick print to see how well your printer can print threads. Ranges go down from M20 to M16 to M12 to M10 to M8 with an M6 to finish it up. Print settings: 5% infill 2 perimeters 0.15 - 0.2mm layer height All parts should thread…
See video for more details.
Bolt on! Another PEG board with screws and threads. Whether as a toy for the kids or as an organisational wall for the big kids ;-), Bolt on can be used for many things. Basically, it's just a board with threads and screws to screw on.…
I added 6mm threads for my push locks instead of inserts to an existing design. I chased the threads with a tap. I also flushed the backside for printing on the butt end due to lifting as you cant really round the corners on this part.…
I had a hard time finding STEP files for NATO gas mask threads, so I made some myself. These are for use in other designs, its not useful to print these by themselves. CC0 licensed, no attribution needed. You may need to scale the female…
This model includes: ✅ 1x M5 × 0.8 ISO thread screw ✅ 1x M5 nut ✅ 1x M10 × 1.5 ISO thread screw ✅ 1x M10 nut All parts are designed to be 3D printable and are great for: Thread calibration (check your printer tolerances) Mechanical…
Dove body wash always leaves a lot of soap in the bottle when the pump runs dry. This allows you to let the last bit of the soap from the old bottle to the new bottle. Screw on and let the bottle drain overnight. Designed to fit the 34oz…
I removed the top 2mm of the bottom so the lid would slip down just a bit so starting the threads is a little easier. Thanks PsychProd for the original!!
This is a quick release plate to mount a GoPro on a generic tripod with ¼"-20 threads. Threaded hole is 6.8mm deep and set up for 0.2mm print tolerance. The plate will accept the official GoPro quick release . Print Settings Printer:…
Length: 180mm. Six models in total. Two bar variants: 1. with 1/4-20 and 3/8-16 threads. 2. with bare holes for (1/4-20 and 3/8-16) brass inserts. Four screw variants: 1. Long screw with 3/8-16 thread. 2. Short screw with 3/8-16 thread.…
Info about Gridfinity I printed it in translucent PLA with a 0.6 mm nozzle and 0.4 mm layer height. Of course you can use finer resolutions.
UPDATE: Completely replaced the DK thread library used for the NPT ports (and the prendered port objects). The new tool is much faster, and renders are much cleaner and lighter. UPDATE: Changed buttress thread to have a fancy radiused…
Update 20240229: Added step file in case any one wants to do a bit of DIY. -------- I've been looking for a mock suppressor that: 1. Looks long but doesn't add too much to the overall length of the gun. 2. Slim but also fits a tracer…
Headset holder for desk. Should fit desks up to around 40mm. Added two grooves on the holder if one would want to add TPU printed/or cut out rubber gaskets for better grip. Infill used for better strength: Gyroid (but use whater infill to…
Print Settings: Printer: Prusa MK2S+ Filament: PETG or PLA Tested with PETG Layer Hight: 0.3 Infill: 5%-10% Rectilinear Exterior Perimeters: 2 Brim: No Heated Bed: Recommended Supports: No Approximated Filament Usage: 11.79m Approximated…
The original Bum Buddy was a neat idea, but I couldn't find a bottle that it fit, so it ended up being useless. I remixed it to have threads that fit on more common US bottles. It has been tested to work on coke brand threads, including…
I liked FFFTechnology's clever little vise but kept being confused by the need to turn the screw counter-clockwise to tighten the jaws. "Righty tighty, lefty loosy" -- not so much. So here's my super simple modification: I just mirrored…
The original model was split in 2 parts, which is not necessary, if you have a 300mm printbed. Also, the original is a little too short, so that the eibos lid fits only with force. I added 1mm of length and chamfered the top part. Lastly,…
These screws are inspired by DINE6921 metric screws with hex flange head and they have metric fine pitch threads . The longer screws have partial threads. My inproved thread design has an accuracy of 2.5µm and should fit without…
Standard M24 Bolt with Left and Right hand threads Also includes Left and Right hand nuts Print Settings Printer: Replicator Clone Rafts: No Supports: No Resolution: 0.16 Infill: 13 Category: Construction Toys
Sharing several simple parametric thread patterns I've used in my 3D printing projects. Depending on filament and printer you may need to adjust the “delta” to make parts fit the way you like. Use negative delta for “bolt” and positive…
This is a remix of dePrintinator's HEPA Filter exhaust in which I added: Magnetic fan cover Filter receptacle which accommodates the flanges found in these filters and allows you to twist the filter into place I replaced the JST-XH…
Climbing stick clip with painter pole threads for mounting. I attach it to an extendable Mr. LongArm pole. Reuse some twist ties to hold the carabiner and gate open. Printed with default settings (0.2mm layers, 0.8mm shell, 10% infill, no…
As I like to keep it simple, I came up with these small clips to complete the Underware under my desk. Printing with three perimeters should provide extra strength. I also uploaded the Fusion 360 file so you can play around with it. There…
to be used when you design stuff
Didn't have any bolts at hand for the original model, so I added the thread for the camera mount, and used a zip tie to mount it to the printer!
This is a remix of the PC4_M10 slot for the original MMU Slot buffer. It contains two models. The first solely includes a recess where the handle attaches to the slot. The benefit is that the original handle can be used and the “fingers”…
There are two versions, with and without threads. I recommend printing with a .12mm layer height, this should allow the threads to print without a problem. If you have issues with the threads printing, use the other model without threads.…
Mostly the same as SPRINKLER base model, but with the BSP 0.75 threads of the inlet port replaced so that they extend to the outer part of the inlet port. The .f3d file is included in case anyone wants to see how the threads were…
5050 T-Slot Nuts - M3 M4 M5 M6 Threads Suitable for: ***Warning: Dimensional Tolerance Notice*** This connector is designed for our standard profile specifications and may not always fit the wide variety of commercial 5050 profiles…
I printed this to use in building the Digital Sundial, http://www.thingiverse.com/thing:1068443 Customized version of http://www.thingiverse.com/thing:193647 Created with Customizer!…
It can be frustrating to reproduce threads found on household screws, nuts, and fasteners with 3D printing. The clearances are very small, the threads are sharp and thin, and the steep overhangs like to sag and collapse. These threads…
Hide a fat roll of benjamins with your bananas in the kitchen, or use as hot dog storage? Maybe give as a gift and see how long it takes them to open it. The threads are pretty tight right off the plate, so you'll have to twist back and…
I modelled a chicken egg. Could be a nice gift for easter or a rhytmic device with rice in it. This is purely practise version for me to understand the process. Please contact me for ideas and suggestions. I printed with Prusa MK4 with…
I wanted to print some Presta valve caps. Unfortunately a lot of the existing models I could find needed weird scaling for the threads to work. I modelled these with the proper #12, 24 tpi found on the Presta valve core. I made a few…
This is a simple adjustable GPU riser, that hides the threads that other models usually have.
With the original version, tightening the holder into the arm on the printer resulted in the roller bearing surface being on the bottom instead of the top. Backing out the holder so the roller was on the top resulted in it being so loose…
In situations demanding a space-efficient and versatile pump connector, look no further than the Compact Pump Connector. This 3D-printable spare part is a valuable addition to your toolkit, designed for home use. Dual Compatibility:…
This lathe change gears should fit most 9x10, 9x12, or 9x14 mini-lathes. This change gear makes it possible to cut metric threads on a lathe with an “imperial” (typically 16tpi) lead-screw. For details on using this gear, see this link:…
You will need a m3x40mm screw and a m3 (preferably lock) nut for and the similar spring to original (maybe longer) for the mag catch system, install like a real one. You will need two m3 nuts and two m3x12mm screws for the mag flare /…
Overview : I have several painter’s poles that adjust to various lengths. I’ve developed a number of attachments for them, but the ACME thread definitions in Fusion 360 are not compatible with the ¾” (075) x 5 tpi definition used for…
Use supports internally if you print it with the GOST threads on the build plate. Otherwise the valve might not work properly. The needle valve (unremixed) was printed with 100% infill.
remix of https://www.thingiverse.com/thing:3725862 cleaned up the threads so that it's actually printable. Flexes a bit under strain, but makes adjusting belt tension so much easier it's worth it. Print Settings Printer: Tronxy x5sa Pro…
These are metric inner threads, exactly as if they were part of a nut. They can be subtracted from your design. You can use them to create a special custom-design nut. You can use them to mount your design or to attach something to it. My…
Printed in ABS at like 20% gyroid infill with 2 or 3 perimeters and it feels pretty strong
Hundreds of UNC hex bolts with partial threads inspired by ASME B18.2.1. The thread lengths for the smaller sizes are not covered by ASME B18.2.1 and have been copied from ASME B18.6.3. All threads comply ANSI/ASME B1.1 with an accuracy…
Print these in black PETG with 5 perimeters. For the logo and shift pattern plates, do a color change after the 2nd layer. The holes will need to be tapped afterwards. There are intentional voids within the part, but they force perimeters…
I don't have a mask that takes these threads, but I used the same method to create the threads as my NATO set. Please leave a comment if they worked or not for you. Threads based off third image in…
DIY Adapter https://amzn.to/4ea2XaZ (rubber seal)
What? This little receptacle can be mounted on the edge of a table top ~¾ inch (~19mm) thick. The top arms angle inwards to help funnel any trash bits into the bin. Originally made for my Tailormade sewing cabinet, so I could sweep my…
Thread moulds for 28.5mm (1 1/8in) and 44.6mm (1 3/4in) pottery bottles. Allows twisting easily because of shape. Has room to use wires to hold it up if necessary.
Just a remix to accept a Bowden fitting instead of a slip joint so I could feed my neptune 4 max from above.
Upgrade your MMU2(s) or MMU3 to use the new chimney released with the MMU3. It gives you a more flexible way to adjust your probe to detect filament in the chimney. I have added threads for the chimney base so that it can be used without…
I remixed the original A motor cable cover with PG7 threads in order to attach a PG7 gland for umbilical setup.
Latest files are available on MakerWorld. Get the full Plate Print Profiles: https://makerworld.com/en/models/244302 === After creating the Pocket Pill Protector I thought to improve the design of my original Screw Top Container So here…
Holder for you boom mic pole or any pole that needs holding. Includes hole with 1/4-20 UNC threads for easy mounting
Took the original Prusa model and added reinforcement and M5 threads for a pneumatic fitting. The MMU2 version of the extruder with the chimney was way too complicated, and I just need a way to connect the normal extruder head to my dryer…
![Broomstick Spearhead [Kenteclaat Remix] (Modified threads)](https://media.printables.com/media/prints/586177/images/4677532_d3bc5908-5c4f-4b0a-b09f-c545092056fc/pxl_20230915_022558869mp.jpg)
