177 models
Create a minimalist and efficient workspace with this vertical laptop stand. By holding your laptop upright, it frees up significant desk real estate and promotes better heat dissipation for optimal performance. This universal stand…
22mm picatinny rail adapter to use in 11mm rail. Needs: 1x 20mm m3 screw 1x m3 nut
The scope mounts allow you to quickly and easily find the proper height. The mounts fit on an 11 mm dovetail and fit scopes with a tube diameter of 1" (25.4 mm). Have now added the mounts in 30 mm as well. The heights correspond to those…
picatinny adapter 20mm to 11mm (lower adapter to avoid raising the sights more)
The adapter is designed to connect a hose to a thread G1/2". Available diameter for hose: 7 | 7,5 | 8 | 8,5 | 9 | 9,5 | 10 | 10,5 | 11mm Print instruction: material: PETG layer height: 0,2mm (0,3mm) nozzle: 0,6mm (0,4mm) support: no…
A light frame for 11mm servo - weight is just around 2,4 - 2,6g Designed for a Graupner C2081 Servo - but other 11mm servos like Hobbyking 939 should also fit. To create a left and right version mirror the STL file in your slicer Print…
There are several variants of e-chain. E-chain ends are compatible with all variants. Segments can turn to both sides (in photo down) Segments are turnable just to one side. Good for horizontal orientation of the chain. (second photo)…
The adapter is recommended to print vertically at low print speed, 100% full, with m3x14 screws for mounting. It is necessary to use a filament with a very good connection of the layers.
I've been working from home for the last several months and I felt myself constantly readjusting my chair because I prop up my feet and I slide back. I've been using them for 2 months, no problems so far. Increase wall count, there is a…
The VW key logo, printed in 0.1 layers, fits perfectly into the key cabinet.
Easy to print! Print with e.g. 7 walls to make it solid. No supports or brim. May use mouse ear if you want. Use manual seam painting and place it on the middle of the standoff, not on the prongs/nubs on the ends.
Simple front sight that slides onto any 11mm dovetail rail as an end piece. Should fit very tightly without any play. Has a slot for a short piece of 1.75mm filament or optical fiber to serve as the dot. Designed to shoot a Steel Breech…
I wanted a decent scope on my Crosman 2250b Ratcatcher so made this. It holds in place on with the force of the scope clamp being tightened and I've had no issue with mine for years.
RV M8 x 11mm Bolt and Nut. Designed to replace bolt/nut on Lance travel trailer stove top glass cover. These fit the back attachment points and hinge in the middle. Likely fits many other RVs with glass covers on the stove top.
Small wrench for 11mm nut which is used to hold kitchen or bathroom faucet. For easier mount I also printed a 40mm bushing because threaded rod was very long. I've uploaded few versions of this wrench. If you use bushing then it's…
This is a remix of the existing model that fits for the thicker MacBook Pro (2023 model) and the iPhone 14 Pro with leather case. Hook is 5mm wide and slot for iPhone is 11mm wide. On the last image is the comparison with another model…
Designed to change the mountangle and adapt for 22mm Mount 1.3 and 5 deg version
Thanks to @Trajan_142247 for his 9mm Hook. I needed a slightly longer version to fit my needs. Thought to share in case someone else needed this. Cheers 🍻 P.S. Is supposed to be a flush fit with the HSW insert but I probably need to…
This is a remix from https://www.thingiverse.com/thing:3309461 using the hose adapter from https://www.thingiverse.com/thing:2735925 . The hose adapter was resized from original 14mm to 11mm. Print Settings Printer Brand: Creality…
PRUSA 3RC Based remix, shorter, without branding for 2x faster printing. Print 2 in 3 hours instead of 1 in 3 hours. Branding removed for easier disinfection as stated by hospital staff. Print instructions No brim required, place 2 in a…
they are thicker than the orginal scales but you can scale them down if you want.
Replace a lost non-metric M11 tube cap. Usually found on shoe paste, glue or mustard tubes. Just measure your tubes thread. If it is 11mm wide and got 3 thread layers. This cap will fit.
Used to fill and drain my aquarium and keep the hose hooked in the tank similar to the Python hook.
I needed an x-acto cover to print in bulk and I couldn't find any designs I liked that fit the larger handles for #2 blades. These will fit handles with 11.2mm-ish (7/16"ish) collars. I like this design because: it prints quick no support…
Print a couple of these guides to help you drill your mast and booms. They are designed for 11mm round spars, such as the ones from Sailsetc or PG. The holes are 1.5mm. Just drill them out if you need a slightly larger hole. The top of…
I needed a hex socket with a hole in the middle for mounting my kitchen Crane. Printed with PLA+ @0.2mm layerheight 15% infill
This is a spacer I made for my adaption of attaching the Luna Float seat to the Veteran Sherman
Non-standard metric size Allen keys: 11mm, 13mm and 15mm. Screwdriver with 15mm Allen Key Shank Combines screwdriver functionality with a 15mm Allen key. Allen Keys: 11mm, 13mm, 15mm Perfect for hex bolts and screws. Print settings Layers…
A cable gland for cables with an outer diameter of 11mm and with a M16 thread. I used it together with the junction box https://www.printables.com/de/model/775897
11mm Dovetail rail replacement for the Remington Express air rifle's rear sight. Uses the existing holes in the receiver that the sight originally mounted with. The many holes in the mount are for scope stop pins, which are on a lot of…
I designed this to make tightening coax cables easier without a wrench. Wrenches are not recommended as they can break the connector if you apply too much force. These finger wrenches allow more mechanical advantage without risk of…
Picatinny rail 20mm to 11mm for red dots or what ever and it rise 20mm or 30mm Print Settings Supports: Yes Infill: +20 Category: Accessories
I was looking for a small case for my home assistant pi 4 setup. I am using the geeekworm x862 ssd drive along with the 11mm embedded heatsink. This is a remix of https://www.thingiverse.com/thing:3714695 .
Print settings Material pla or petg Walls 3 Infill 15% Layer height 0.2
If you want to make me happy and you have Discord, join my server ;) https://discord.com/channels/974098819379777566/1053870875444785163
These tiny ampoules are very difficult to both hold and draw from at the same time. They can stand on their own but just barely and tips over at the slightest touch. This ampoule holder gives it the stability to stand easily and be…
3mm, 5mm, 8mm, and 10mm Speaker Baffles for the CRude Engineering 15x11mm Sugar Cube Speakers Speaker for sale on https://crudeeng.com/products/256019636071 Use code PRINTABLES for 25% off your speaker order!
Pipe connector with 11mm Outer Diameter and 6mm Interna Diameter. Suitable for joining 2 hoses with 10mm ID, requires 2 hoe clips or cable ties to seal the hoses. I printed using PLA, 0.2mm Layer height, no Support Required when standing…
For use with M3 nuts, bolts and washers. Recommend printing upright intough resin for sharp points or alternatively in PETG on a fillament printer, witha a <0.4mm Nozzle. Not tested in PLA. Category: Parts
Used to insert an 18mm glass piece in a 11mm ish bong opening
Couldn't find a design to fit a 30mm scope to a 9-11mm dovetail rail, so made one. This seems to work fine for holding an old Gamo red dot scope to an HW40. Two sizes included - normal and thin. I recommend the normal size. I printed both…
cortador pet botella con espacio para una platina metalica de 1.5 mm para protejer el plastico de desformacion,
Generated with Rhino 7, Grasshopper, and Kangaroo
just a simple spacef i made to move a bracket out by 11mm. i made it for a m4 bolt. when printed tho the screw had to be threaded through the spacer so i had to use a drill bit to open it up a little. im uploading this just as a test to…
Tested materials: PLA, PETG, ABS, ASA Tested layer height: 0.2mm (thread is toleranced therefore) Tested printers: Bambu X1C (Bambu Slicer), Voron 0.2 (Cura) NO supports needed, but you will need a few seconds more to assemble the inlets.…
Liquid funnel for refilling e-liquid bottles with an opening of 11 mm (Chubby Gorilla Unicorn 60 ml). Optimized for a quick liquid flow, makes refilling your bottles from a big flask fast and easy going. Print instructions Printed with:…
version for table raised by 11 mm with spacers. For setup https://www.printables.com/model/1202837-air-duct-for-chc-hotend-installed-on-k1c-creality
This one has not been tested yet but is using the same design as the 14mm which has been tested. I made this 11.4mm inside. Tolerances are 0.2mm so print this first- https://www.thingiverse.com/thing:3569489 More sizes to come. I…
Korsar dovetail 11mm to STANAG (Piccatiny) rail adapter, Use ABS with support
Hi ! Sadly my christmas led string was defective when i have put all the illumination on my christmas tree, i decide to investigate... i found easily the cable was broken at the plug entry, unfortunatly this plug is moulded.. The only…
11mm diameter sheave block designed for use on an rc sailboat. For assembly you will need the 3 printed parts along with a piece of filament and 150mm of line ~1mm in diameter. Assembly First clear out the two small holes on both body…
Türerhöhung Fitschenring Türbandring 11mm
Introduction This is a 6mm (1/4 inch) hex-bit driver I made for my 111mm Victorinox SAK. It will only work with 111mm Victorinox knives, but I will make one for 91mm ones as well once mine arrives. I tried to make it as durable and…
A simple bracket for mounting a Ziply/Verizon/Frontied I-211M-L ONT in a Leviton structured media center. Requires 2 #8 panhead screws and two 47615-NYL mounting pins. The holes for the #8 screws are 70mm apart. Print Settings Printer…
Plant holder for garden supports 11mm
Note: This stand requires the original mount that with AC511M to work.
A simple stand for an office chair. Compatible with 11mm wheel hole.
Two drilling depth sensors that cover the drill diameter from 1 mm to 11 mm. It is convenient to have only 2 limiters instead of 5 or 6. They are easier to find storage space, they take up less space in the case for a screwdriver or…
Hikvision base, one tilted by 14°, one normal. With hole for a PG16 grommet for ethernet cable. Included small grommet/end cap for microphone cable, if you have "-IS" version. A low ring is for testing. Layer 0.25mm, Nozzle 0.4mm, Infill…
It's an 11mm DD shell I created for my DIY, I haven't ordered parts for the DD shell but I'll edit this post once I have gotten it. Anyway, feel free to modify the shell to your liking, be sure to use a small nozzle size for printing to…
I have a floor drain, basementstairs coming from the garden. Often found little babyfrogs down there and was wondering, where they came from. Some day i saw them coming through the floor drain. I didn't want to step on a babyfrog, so i…
Print on the side to avoid overhangs and ensure the best strength. If you want it tighter you can downscale it a little bit. You can also use “break to bodies” button in your slicer to print a single piece and test the fit. p.s. Please…
Very small and simple pill box - 24mm x 11mm. Can be printed with standard (will work fine) or high settings (nicer look).
I'm unhappy with how this has turned out, it wobbles too much to be useful. Use my updated design, V2 which clamps to the barrel properly and securely. It is a great improvement. For mounting a dovetail optic on a barrel. Either on the…
Differences of the remix compared to the original I took an already remixed version, from the1maximus, I really liked how he had created Betweeners that matches the corner profiles. I didn't need the LED 45 degree mountings so I removed…
Customized version of http://www.thingiverse.com/thing:16627 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: idler = 1 no_of_nuts = 1 pulley_b_dia = 20…
T-Shaped laminate floor space for expansion gap. I printed 30 of these and used two per board length and 1 per edge. You may need more, if you do just print more. My flooring was 8mm thick with 3mm underlayment. I set this up for 11mm so…
Needs to be printed with support. I printed in translucent Petg. Follow any other instructions from original print.
Connector for garden supports 11mm Off course 2 pcs is a set. You need also M3x6 and nut.
Needed a mount for my Fluval planted light that would fit a 20-gal long rimmed tank, and saw this one made by Nolibert. However, it wouldn't work for my tank or light since it's far too small, so I made some minor adjustments. Tank grip:…
Customized version of http://www.thingiverse.com/thing:16627 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: idler = 1 no_of_nuts = 1 pulley_b_dia = 20…
Gridfinity Socket Holder for Dewalt Deep Metric Sockets, Size 7-11MM, 1/4 Inch Drive 2x3 Gridfinity Grid I mistakenly overwrote the fusion 360 file for this model, so sadly there is no source available. These sockets are part of a set of…
Hose adapter 11mm to 7 (from an 11 mm valve to a 7 mm pipe) Adaptateur de tuyau de 11 mm à 7 (d'un robinet de 11 mm à un tuyau de 7 mm) Print Settings Printer: Artillery SideWinder X1 Rafts: No Supports: Yes Resolution: 0.2 Infill: 10…
Mit disem Klip kann man ein Kabel einer 11mm dicken Stange entlangziehen. Andere durchmesser gehen auch, man muss den Clip entsprechend skalieren.
My parents bought an IKEA Baggebo shelf for storing trays of small plants in the spring. With this attachment they can move it around freely. Originally it was designed for some rollers with M8*12mm theaded rods in the top, but I also…
This is a picatinny to dovetail adaptor for mounting optics to whatever you have picatinny on. Feel free to judge my f360 files. All files are 50mm in length, if you want a dif size just send a comment. PRINT INSTRUCTIONS Print both the…
I ordered a Drag Chain and needed a couple more end pieces.. Befenybay R18_10x11mm_outside open I used Organic Supports, 0.15mm layers As always, I've included the Fusion360 files(in case you want to mod)
I have a newer honeycomb from XTool and the holes are 11mm in size and the hurricane bases for this alignment tool is 8mm. So they didn't work for my honeycomb and I design a new base to accommodate my honeycomb.…
Customized version of http://www.thingiverse.com/thing:16627 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: profile = 12 teeth = 24 additional_tooth_depth =…
I always find myself searching and rummaging through my toolbox for the right wrench. To solve this, I decided to organize them neatly on my Honeycomb Storage Wall. However, I didn’t want to place each one into a specific holder manually.…
Couldn't get the mounting rings i wanted, at least not for a reasonable price, so i designed my own. 11mm Dovetail Mount as found on many air rifles and the like. On PCP / low power rifles the mounts are sturdy enough. Depending on the…
holds cables nearby. added material to the corners. gcode has supports baked in
This item was initially designed to replace a broken roller blind bracket. That particular roller blind had cogged inner recess (which the 11mm version matches). But these can be used in general with hollow metal rods, so have added…
Rear motor mount for the HAWk Modular RC Wing Airplane with 11mm hole spacing and 3M screw holes (2.6mm hole diameter for self-threading). Recommended print setting sparse infill 100% for maximum strength
Quick replacement part to make the mount that comes with the Dell Stereo SoundBar AC511M useful if you don't have a dell monitor stand. Unscrew the existing front plate from the mount and screw in the new 3d printed part, assemble like in…
Friend needed some longer camera mounts for their pro cam so I quickly whipped these up Its not really 11mm long but its something close to that
Klucz do baterii umywalkowej 11 mm Długość klucza 80 mm dodatkowo kwadratowy rządek natkę grzechu. Dodaj także plik .step do zmiany.
Raiser for doe rolling pin. Attach these to the end and you will exactly 3mm high dough. Really good in case you are making thin sheets of sugar coating to cakes for example. Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts:…
Adapter to convert muzzle on KWA KMP9 to 11mm thread to make it possible to fit your suppressor or tracer unit. Slide in and turn then tighten the thread to a tight fit.
A cover for the X-ACTO Knife with a 7/16" (11mm) Handle
The housing was designed to mount a toggle switche on my Ender 5 to switch the build plate lighting. Of course the housing fits other Printers as well which use the 20mm extrusions with 6mm slots. For mounting you will need two screws M4…
this holder lets you hold 6 shafts, 3 darts, 6 points, and 36 flights.
7070, 5050, 4040, 3535, 3030 Footprint. Height 0.6mm - 1.0mm. PLA not recommended due to 50°C heat deflection temp, starts softening. I use ASA for 100°C HDT, but PETG should be fine for 70°C HDT. Use white colour filament. 0.08 - 0.1mm…
