193 models
Would appreciate your make, a like and/or voting ;-) The wonderful Muli cycle carrier bike (https://muli-cycles.de/de/bikes/motor) has one weak point. When the bike is set out to rain/ wet weather-conditions, water tends to stay in the…
Print approx. €0.38–€0.47 excl. taxPreliminary estimate for one variant
After printing, bend the inner part out slightly so that it can snap into place later. Printing in PETG 15% Infill 0.20mm Quality
Print approx. €0.67–€0.82 excl. taxPreliminary estimate for PETGSource material: PET
Textima 8014 sewing machine repair part. The bolt sockets from the original part must be transferred and heat-fitted into place and some modification need because of the spring.
Print approx. €0.69–€0.85 excl. taxPreliminary estimate for one variant
For some reason, MFG of this Omron Air Compressor Model NE-C801 made a mount for the inlet cup that doesnt actually work! So I used this existing mount edge to make my own mount! And added a little tube holder since I dont want my…
Print approx. €0.33–€0.41 excl. taxPreliminary estimate for one variant
🟦 Zetor Crystal 8011 🟦 UPDATE https://www.printables.com/cs/model/446803-zetor-crystals-update-for-attaching-a-trailer-no-s From this day on, all my models will be in the better 3MF format Look forward to other similar models, I will be…
The existing 30mm fan for cooling the Raspberry Pi, BTT pico board and stepper drivers may not be sufficient if users want to fully enclose the V0.2 for ABS, ASA or Nylon with a hot chamber. I design a back panel to install a silent…
All the mounts I could find mounted the fan too close to the underlying surface when using the original feet, so I had to design my own.
This is an easily printable bearing (more like a bushing) with the size and shape of a standard 6801 ball bearing. It has two separate pieces that when printed are captured together but can still rotate. This works for a stand-in while…
FDM friendly version of the Mercedes hood emblem, optimized for 0.4mm nozzles. Will give even better results when printed using 0.2 or 0.25mm nozzle and 0.1mm layer height In three versions: Fully blank emblem plate and insert in one…
Just wanted a quieter printer, when it is idle. The Pi gets hot on it's own and needs some cooling, so I designed this back for a larger fan. You can connect it directly in place of the old one. BOM: The fan is 8010, mounted with 4…
I’ve designed a simple yet highly effective fan bracket to replace the bulky factory-installed one. This custom bracket fully covers the control board (mainboard) while still allowing for excellent ventilation. It’s designed for use with…
Wall mount your JC8012P4A1C panel in style with this bracket! Avoid cutting into your wall to get that flush mount. Two versions are included: a landscape and a portrait bracket. A small hole is placed at the bottom right of the mount to…
a mini Whelen 2801 Omni directional siren Print Settings Printer Brand: Creality Printer: Ender 3 Pro Supports: Yes Resolution: any Infill: i used 10 gyroid Notes: you can print it as one piece with a really annoying support removal or…
— — — Edit 11.06.25 Added CAD files — — — I couldn’t find a 10-inch rackmount that fit my MokerLink 2G080110GSM switch—so I designed one myself! The switch slides in from the back and is held securely in place by built-in hooks,…
Before you go further! This model is available for free for all my supporters in Printables Club 🧡 Consider joining my club to have access to all ⭐⭐⭐ exclusive projects ⭐⭐⭐ and be part of my community! This project is for personal use…
Clamp for the Hakko FX-8801 handpiece (supplied with FX-888D) from fns720 's h eat-set insert press modified to fit thrutheframe 's press for 2020 extrusion and MGN9 rail. The clamps are secured with a 40mm M3 bolt. Two versions are…
Print in asa, abs or petg. Use same parameters as other parts
This model is compatible with the lego system.
After my child did a pull-up, the clothes rail bracket broke. Unfortunately, this is no longer available at Ikea and so I designed it quickly. How I did it with a cell phone, Inkscape and Tinkercad, you can see in the video. Mehr…
Kluczyk do zastosowania z kluczem 13mm lub grzechotką ¼"
This model is compatible with the lego system.
Front tire for Husqvarna Automower 315, 320, 33X 430X 450X. Printed in Filamentum FLEXFILL 92A.
Volvo XC90 Folding Folding Seat Latch Release Handle (Rear, Interior code: RXXX, RXXX). Volvo original PNs: 39826799 ; 39826801 Two files, with and without Volvo logo available. If printed in high strength material (PETG, PCTG, PCCF etc),…
VAG clips N90833801 made in the program: Autodesk Inventor Filament material: COPET Resolution: 0.2mm V2 - stronger version( 02.04.2025)
The Ironclad Sentinel: Unleash the Power of Advanced Robotics for Your 3D Prints! By KRIT YAMSASO (YAMSASO DESIGNS) Step into the future of 3D printing with The Ironclad Sentinel, a formidable robot design meticulously crafted by KRIT…
This is a highly detailed fan-made bust of the iconic T801 – a cybernetic guardian with partial endoskeleton exposure and battle damage. Designed for display, this model combines mechanical aesthetics with character accuracy, perfect for…
Einsatz mit 24 Fächern für die "alten", kleinen T-Loc Mini Systainer. Insert with 24 compartments for the "old", small T-Loc Mini Systainers. Passt NICHT in die neuen Festool Systainer³ SYS3 S 76 NOT compatible with Festool Systainer³…
The Ironclad Sentinel: Unleash the Power of Advanced Robotics for Your 3D Prints! By KRIT YAMSASO (YAMSASO DESIGNS) Step into the future of 3D printing with The Ironclad Sentinel, a formidable robot design meticulously crafted by KRIT…
The Ironclad Sentinel: Unleash the Power of Advanced Robotics for Your 3D Prints! By KRIT YAMSASO (YAMSASO DESIGNS) Step into the future of 3D printing with The Ironclad Sentinel, a formidable robot design meticulously crafted by KRIT…
The Ironclad Sentinel: Unleash the Power of Advanced Robotics for Your 3D Prints! By KRIT YAMSASO (YAMSASO DESIGNS) Step into the future of 3D printing with The Ironclad Sentinel, a formidable robot design meticulously crafted by KRIT…
Gedruckt aus TPU 98A von 3DJacke. Auf die beiden Dichtlippen achten, diese zeigen bei der Montage nach außen.
Tool zum Öffnen und Zudrehen mit dem richtigen Drehmoment. Passt auf einen 1/2 Zoll Drehmomentschlüssel oder Ratsche. Der Durchmesser beträgt 40,7 mm mit 16 Zähnen. Ich habe das Tool aus PETG gedruckt. Bis 45 Nm kann man die Lager…
I haven't tested this yet but I'll be doing the 20K km service on my Street Triple soon and need this tool. Let me know if there are any issues with it. Designed for a 22mm socket. You'll need to consult your service manual for the torque…
There are several mounts for the Shimano BT-E8010 battery but they seem overcomplicated to me so I came up with this. The battery stays upside down and it's kept in place by it's own shape & gravity. Print settings Material: PETG…
Simple, well-fitted cover replacement for EA80* KRUPS coffee machines series. If you e.g. lost your original coffee container cover, use this one. Printed in PLA+ with supports, 0.4 nozzle, 0.2 layer height. I used mounting position…
Dishwasher spare part 807035801 8070358018 Mounting Holder Bearing Headboard for Spray Arm For: AEG, ZANUSSI, ELECTROLUX, WHIRLPOO
Ender 3 mainboard cover with 80mm x 10mm (8010) fan mount. Integral rear facing silencer. Mount fan from inside with 4mm x 12-16mm screws. Print inside surface facing down. No support required. Enable bridging. Print Settings Rafts: No…
LED Strip Mount (WS2801 5050FC32-CV)
TV Stand Feet for Kogan 49" Smart 4K TV (KALED49MU8010SZA) We used to have this TV wall mounted, but regrettably, threw away the stand. Since we took it off the wall later on, I made up some 3D printable feet! Requires 4x M6 40mm bolts.
Introduction When I decided to assemble my HomeLab Rack I wanted each device to have its own dedicated holder, as I like to keep everything tidy and wanted to avoid a mass of shelves. Unfortunately I couldn't find any satisfactory…
In der Scheune wird es im Sommer zu warm und die Fritzbox hängt sich auf, daher nun eine Variante mit Lüfter, welcher vom USB betrieben wird. Mit genug Platz für Luftzirkulation sinkt die Temperatur drastisch. Lüfter ist seitlich versetzt…
This is a 2x1x3 Gridfinity bin for the Wiha 3801 stubby screwdriver. I believe this will also work with the older 380 model, but I have not tested this. It will not fit the newer 3802 stubby, nor will it fit other model stubbies (281, etc).
This is similar to another Eyoyo 8" 4x3 monitor stand , but with the following differences: Monitor tilted 20 degrees back instead of 10 degrees Larger, heavier base, with more material in back to make it easier to press buttons on the…
A0029880181 Clip für den Daimer, gedruckt in PETG oder PLA, ca 15 min.
10-inch 1U rack mount version for YuanLey YS25-0801 ethernet switch. Printed the ears with long edge on build plate. Source: yuanley_YS25-0801
Camar/Forest 801 cabinet hanger covers modified to be longer and with wider skirt. I printed mine with PLA, standing on the skirt using tree support. Step file attached so everyone can tailor for own needs.
Have owned this Irwin Tap and Drill Set for years, and every time I used one of the drills and taps I would invariably bump the open package and knock all of the taps and drills out onto the floor. Hate is a strong word, but I really…
Handy little cap to keep stuff out of the battery port when transporting the battery. I printed with PETG, fits snuggly, I don't think it's suitable for flexible materials. Print settings Material: PLA/PETG/ABS/anything solid Resolution:…
I have a Glitter 801D battery spot welder and while it comes with a stand I wanted one that would hold the electrodes and also the nickel strips. This was made by scanning the electrodes using a RevoPoint POP2 and using the scanned model…
Simple DIN rail mount for Huawei OptiXstar EG8010Hv6 modem. Part1 and Part2 should be glued together
Modified Ender 3 PSU cover for 80 mm x 10 mm (8010) fan. Integral rear blowing silencer. Mount fan from inside with 4mm x 12-16mm screws. Print inside surface facing down. I used 20% support density with 2x gradual support infill steps,…
This is a remix of the low profile version of https://www.thingiverse.com/thing:2153437 by @bobtidey. I created a cap for the power button, extended the lid 1mm to center it better over the I/O pins and added a little hole over the reset…
Hier biete ich den vorderen Filterdeckel mit Schlauchanschluss für ältere Entlötstationen von Weller an. Meine ist die VP 801 EC bei der leider der vordere Deckel mit Schlauchanschluss defekt war. Habe nun beide Deckel für den 3D Druck…
ULO EBL Type 801 casing for vintage mopeds. I needed a replacement case when I restored an old vintage Puch Montana from the 80's, this is the result.
UP1801 is a model rocket that is launched with 18mm model rocket engines and can be flown with or without an altimeter payload. Holes in the sides of the body section allow for barometric altimeter pressure equalization. Requires model…
Ein zweiteiliges Modell zur Reparatur des Drehgelenks an der Makita Akku Leuchte DML801. Die Bauteile können ohne Stützmaterial gedruckt werden und ersetzen das original Drehgelenk, ohne das die Kabel im inneren der Leuchte abgelötet…
This hinge ist for the AEG Parts numbers : 2231129012 2231128014 Left and Right are identical I was very fried and really pissed off at AEG for their crap quality this hinge broke after 3 months of use and even after two new free hinges…
T-piece original nr. SB-112801 Category: Outdoor & Garden
This remix wraps the Guition 10.1" / JC8012P4A1C display in a clean, frame-style housing suitable for wall mounting or desktop use. What's in the download: Source: STEP files are provided so you can adjust the dimensions or mounting…
A simple stand that holds the battery upright. It might fit some older/newer Shimano batteries too, as long as they fit into the same bike. Open the charging port cover before inserting the battery ! If the stand feels a bit top-heavy…
A conversion from 2x 4020 cooling fan to 1x 8010 fan over the mainboard to cool stepper drivers and host CPU heatsink. To do this mod you have to change the stock heatsinks of the TMC2209 drivers with low profile type, better use copper…
This model is compatible with the lego system.
I didn't see it directly but my jigsaw was crooked due to two holes being drilled non-horizontal internally. It resulted, at first, in my jigsaw cutting into the plate and ended up shattering it completely after some use. I remade the…
My original power button on my coffe machine (Krups EA8010) had broken, so I designed this model to fix it. It fits OK on the PCB - it's not terrible, but definitely usable - and the small mounting legs are a bit fragile and tend to break…
Hey, this is a simple holder for the Roco/Fleischmann 10764/680801 digital control unit that goes with the first generation Multimaus/Lokmaus. It can be mounted using for screws. Two holders are required for mounting.
Maytag and other brand fridge part that is no longer made
New Krups buttons, maybe they will need some adjustment. I got no feedback.
Holds the following capacities: 15x 608 (3 slots) 14x 6801 (2 slots) 14x 625 (2 slots) 14x 624 (2 slots) 18x 623 (2 slots) Printed with PETG 2 walls, 8% lighting infill
This is a mount for the M4P in the Switchwire. It's REALLY tight. You need 90º USB adapters to use the USB ports on the M4P, but this blocks the Ethernet port. Installation: I also added a mount for an 8010 fan to cool the steppers, this…
The spare tyre carriers on VW Transporters have spacer sleeves on their support bolts which are apparently intended to prevent over tightening of the carrier. Unfortunately despite being designed to be held on captive “barbed” bolts, they…
This a simple tablet holder for the FYC JK8801F Folding Treadmill. The area for devices is far too small for a tablet to sit in landscape view, so I created this that slots into the existing device holder. I printed mine in PLA with 15%…
This is a drill template for making 10mm holes for the Camar 801 (also sold by Hafele as 290.40.905 and 290.40.906). Note that dimensions are very slightly larger than recommended by Camar — I found by experimentation that the recommended…
Parts slightly modified to suit the characteristics of 3D printing
I really liked the original ESRack system design created by @EvilProphet . I create my own support for GPON Terminal Huawei HG8010Hv3 from the Blank Module and share it here You can put the Huawei HG8010Hv3 on 2 side (connecting on front…
-Lav cage requires paperclip pieces to glue in (don't use pliers as they may create burs that catch on cloth). Widen holes with tweezers if necessary . -tapedown clip is superglued to a piece of leather. -use clear nail polish over top to…
DXF for laser cutting and STL for printing. Here's my config based on BTT skr pico [temperature_fan Panel_fan] pin: gpio20 kick_start_time: 0.5 sensor_type: temperature_host control: watermark target_temp: 50.0 # max_power: 0.9 min_temp:…
Hier biete ich den hinteren Filterdeckel für ältere Entlötstationen von Weller an. Meine ist die VP 801 EC bei der leider der vordere Deckel mit Schlauchanschluss defekt war. Habe nun beide Deckel für den 3D Druck konstruiert. Als…
Just a different version of the cover for https://www.thingiverse.com/thing:4083857 to have a 8010 cooling. This was not printed so please report any issue and post your make if you are printing this version so i can mark it as no longer…
I modeled a spacer bracket so the door would fit with other part cooling solutions as well. Link for Bracket Here the honeycomb grille can be a bit tricky to print if you are on a .6 nozzle. it will not slice correctly unless you set your…
My version is 20mm longer, due to a different layout of my Artillery X4. I do not know if this is a difference between pro and plus s1 version, or different hardware manufacture date — Original description from Andrzej:…
This is a snap in adapter for the Hako FX-8801 soldering iron used with the Modular Arm by @reemo3dp and for the heat insert press here: https://www.printables.com/model/808502-heat-insert-press Printed my first one in glass filled PETG…
Náhradní víčko pro konvici Catler KE 8010.
Dual DAR filter adapter design for m8018 abcros mask. Print instructions PET-G Infill: 50%+ Contur 4x Support : no
The Sunbeam EM0480 coffee grinder has bulk grind adjustment achieved through adding shims under the burr attached to the motor. They come in 0.25mm increments but they leave a small gap under the burr which can trap fine grinds. If you…
The fan does not have a speed control, so the 3296W 500 ohm tuning resistor is also mounted. It is enough to reduce the speed by 50%. Just insert and move it up. M3 threaded inserts with a length of 3 mm were used for fixing in the power…
I have ZTE MC801A1 5G Best covarage is at the Window so I made this design
This is a programming jig to program the relatively inexpensive HolyIOT 18010 NRF 52840 chips. This design requires pogo pins P50-B1 (0.5mm Length 16.35mm). The fit is very tight and I recommend re-enforcing your solder joints with epoxy…
This model is a remix inspired by 👉 Rugged Multipart Wowstick Case V2 by NikitaDKS Original: https://www.printables.com/model/427337-rugged-multipart-wowstick-case-v2 The outer design concept served as a reference, but the internal layout…
Organic suports. Check shield (optional, but with better pinout then original) https://github.com/FRautenberg/Logic-Analyzer
A light burnt out in my Onkyo amplifier. In my case - the “Super Servo” one. The original part was flexible, so after many iterations I have landed on this particular design which can be printed in PLA and is just flexible enough. It…
The holder is without holes due to its design. The holes need to be drilled during assembly. There is a storage space for the cable at the back. Suitable for use as a screen for a chip device, or as a photo frame. The top cover serves to…
Nachmodelliert vom (gebrochenen) Originalteil. Aufdruck der Fadenführung als erhabene Kontur hinzugefügt. Es sind das originale Lochblech und der Druckknopf für den Lichtschalter erforderlich. Falls noch eine Glühlampe verwendet wird, ist…
Print upside down, lying flat on the top.
Mamce na digestoři chyběla krytka žárovky. Jelikož byl rozměr díry 6x18cm, tak byla tvorba nového velmi jednoduchá i v Tinkercadu - jen váleček a kvádřík! Po chvilce přemýšlení nad co nejjednodušším designem, je to vymyšleno tak, že se…
![Display Stand for LEGO NINJAGO Dragon Rising 71801 / 71802 / 71803 [last update 12.02.2024]](https://media.printables.com/media/prints/762092/images/6042600_120223d5-b10b-4048-beea-1b98e3640694_699057dc-07eb-4476-848a-dc9cb0bae83f/71803-1.jpg)
![KRIT YAMSASO [20250928010]](https://media.printables.com/media/prints/d422032e-9dc3-435c-936e-e940745dcba5/images/10777285_4b04d07e-25e3-4e1c-8354-8da82f1f9fe2_00193e95-6ce6-4784-9d75-af23e69c5401/010.png)
![KRIT YAMSASO [20250928012]](https://media.printables.com/media/prints/f329c1ab-a9a1-419d-8d38-d870e9d8f25f/images/10834670_f0201601-7eea-41da-86fd-578a62beb553_a625444e-8c1a-41ae-b240-6965c3e771ca/012.png)
![KRIT YAMSASO [20250928013]](https://media.printables.com/media/prints/10358b81-84d9-47af-8b3a-1db4f3930538/images/10834692_cedf4bb9-78a1-451b-a9de-eaafa0a3ba64_f357cd1c-6d05-4e70-a36c-09902acc3798/013.png)
