Counting matching models…
===== CZ ===== Jedná se o kompletní krabičku pro převodník GBS-8200. Pokud stahujete mé modely, přispějte mi na vývoj pár korun. Vás to nezruinuje a mi to pokryje alespoň část nákladů na materiál spotřebovaný na testovací výtisky a…
Had someone ask me to model this up for them. They bought a similar one off Ebay and didn't like how thin it was, so I bulked it up a little and increased the supports. Holds the Dewalt DCHT820B hedge trimmer but I'm sure it could be…
Ersatz Gummipuffer Heckklappe am Megane 2 Coupe Cabriolet. Da dieses seid Jahren schon nicht mehr bei Renault verfügbar ist, habe ich selber einen Designend. Die Montage ist etwas unentspannt, da die Aufnahme sehr eng ist. Mit etwas…
Dremel support 8200 and other the pieces fit perfectly, if necessary give a little bit of sandpaper Print Settings Printer: Anycubic i3 mega Supports: No Resolution: 0,2 Infill: 20 to 100 Category: Machine Tools
Maturity: Good 3 prototypes. In use since 2024/02. You may add a pad as in my 3mf file to get a better printability. Print without support.
Arris Surfboard SB8200 Rack Mount Enclosure I wanted to rack mount my SB8200 but in doing so and placing it between 2 pieces of equipment it would overheat as it is passively cooled. So I set out to design an actively cooled rack mount…
Print using supports, at least 20% infill in your material of choice. I used PLA, and it works great. The V2 version has a support that pushes the blade out away from the wall, so that the hedge trimmer has a more vertical resting…
Support mural Bosch AL 1820 CV
GBS-8200 RGB to VGA Video Converter Board + SCART Case Remix adding housing for a SCART plug. This is the PCB mounted right angle version which clips nicely into the housing with the pins exposed so these can be attached to the wires as…
Will fit most Arris Surfboard Models (8200, 6141, etc). Complete re-design to fit the SB8200, re-measured, redesigned, and printed at least 10 different versions to ensure a nice fit on my own SB8200. Hopefully this fits better than…
Simply and fast printing wall / under mount for your Arris Surfboard SB8200 modem
HP Elitebook 820 G3 Ethernet port cover should be ok for other models from same generations, but i didnt check
A mount box to hide the cables that come out of the RLC camera. This one is made for my RLC 820A but it will probably fit other models as well. You will need some M3 heat-set inserts to put into the holes. Alternatively just edit the…
===== CZ ===== Jedná se o kompletní krabičku pro převodník HCKJ-8200. Upozorňuji že deska HCKJ-8200 má trochu jinak rozmístěny součástky než GBS-8200! Proto i design je jiný, viz foto. Pokud stahujete mé modely, přispějte mi na vývoj pár…
I made a vacuum hose adapter for my WORX WX822, since the tool originally only comes with a bag-like attachment to catch dust. It fits a 34.5mm vacuum hose, but the Autodesk Fusion files are included, so the model can be customized. This…
Oil Filter Wrench for Motorcraft FL-820S. 15 Flute, 93mm. Hand or 3/8" drive. Print face down with no supports. Compatible Vehicles Cadillac - STS V8 4.4 (2006-2009); XLR V8 4.4 (2006-2009) Chrysler - Aspen (2008-2009); Sebring V6 2.7…
Gridfinity compliant, low-profile tray/holder for the IWISS IWS-2820M and the IWS-2412M open barrel terminal crimping tool. I did not completely design it from scratch. I used schenklooza 's excellent Gridfinity Parametric Blank bin as a…
Case for GBS 8200 VGA video upscaler with GBS control The housing consists of two parts that are screwed together. Power of device is taken from USB micro module and runs through a switch On the lid there are holes for OLED and encoder.…
The first layer is 0.15 The remaining layers are 0.08 Width 0.4 3 perimeters Filling in 100%
This simple construction are for upgrading your K8200/3Drag to GT2 belt on X axis. It is a direct replacement, reusing the original mount screw and holes, adding the missing belt tension. For complete upgrade of X axis to GT2, you need:…
This simple construction are for upgrading your K8200/3Drag to GT2 belt on Y axis. It is a direct replacement, reusing the original mount screw and holes, adding the missing belt tension. For complete upgrade of Y axis to GT2, you need:…
Single piece hanger to fit a Ridgid 12cv lithium R82009 drill. Screws flush against wall. Quick and dirty design. I've not used supports, but my printed handles overhangs very well. As always, PETG is ideal for functional prints, but PLA…
Fahrradhalter für die Kurbel von Shimano GXR 820 Dieses Modell ist für etwas breitere Kurbeln und weniger Abstand zwischen Kurbel und Pedale. 90mm Höhe zur Pedalachse 40mm breite der Kurbel 20mm Kurbeldicke Angepasst für Giant Revolt…
The Brother QL-820NWBc label printer does not come with a bin to catch the labels that are printed. Therefore, these just fall to the ground. To solve this issue: a bin to catch the labels. This bin interfaces with the holes on the bottom…
Thanks to @Lannix3D for the original! I printed with no supports, removed the skirt loop and added some brim so I could print in one session aka all fit on the builtplate. I would recommend printing only the outer brim on the basket.
M3 heating nuts are used in the case. The speaker can be fixed with a hot glue gun. Inspired by this: https://www.thingiverse.com/thing:2931496
This is a small rain cover for a eufy Doorbell 2K HDR T8200 with optional mounting wedges (15° or 30°). I glued the 30° mounting wedge to the rain cover with epoxy glue and attached it to the wall with the eufy mounting plate and 3.5x40mm…
Introduction I've been printing a bunch of ESRack things for my work and home racks and I've always wanted to rackmount these annoying cable boxes. Unfortunately they have a case that's almost exactly 1U high, so the standard ESRack…
My version of GBS Control case for GBS 8200 and two sizes of ESP8266 modules, plus RGBS BNC connectors. The two sizes of the ESP8266 module supported are: 48 x 25mm 58 x 31mm Please choose the corresponding one when you print. Project is…
A case I designed for my HomeAutomation server based on Raspberry Pi 3B. The case is for: Raspberry Pi 3B Geekworm x820 Storage board v3.0: https://wiki.geekworm.com/X820 Geekworm x735 Power Management shield v3.0:…
Simply mount air nozzle on focusing lens. This should also fit on other Neje laser modules like A30130 External diameter of air input is 5mm. Nozzle mounted on laser: https://www.youtube.com/watch?v=fPiL8KUA4E4 Category: DIY
Here's my rebuild of the X and Y axis of the Velleman K8200. It features GT2 belts, tangential clamping for the use of Igus linear bearings (Also works for normal ball bearings). It is way more sturdy than the original design and it…
The mount may fit other 75% keyboards. Check the second picture for keyboard dimensions. Also fits my GMK67 65% Mechanical Keyboard.
You'll need: 4x 608 Ball bearings 2x M5x12 screws with corresponding nuts 4x M6x30 screws with corresponding nuts Print: 2x Spool Holder Arm 4x Spool Holder Spacer 4x Spool Holder Roller
This is a 2-part replacement case for the RTL SDR (model R820T2). It has provisions for the external antenna, a light-pipe for the LED indicator, and 5× light-pipes for the IR receiver. It also has hexagonal cooling holes on the bottom.…
You can use this nozzle on your Ryobi air blower to remove dust, and it’s especially useful for drying your car after washing it. You can modify the size of the nozzle in Fusion 360 using the provided file. By default, the air outlet…
This is designed/remixed to specifically hold the Arris Surfboard SB8200 Cable Modem and adjusted the pieces to reduce the flexing seen in other prints for this modem. Specifically, the tolerance causing the face of the mount to push…
Sur inspiration de gloda et Andy Forsberg , un redesign pour le AL1820cv. Fixation murale pour chargeur Bosch AL1820cv Impression en PLA en 0,2mm sans support
40mm fan mount for the All-Metal E3D v6 Hot-End to Velleman K8200/3Drag standard filament extruder. Fan duct snap on reusing original extruder screws and spacers, optimized for robustness and easy print. The 40mm fan is more quit than the…
To adjust the B-screw of the rear derailleur RD-RX820 and RD-RX822. Set the gap between the largest pinion and the guide roller: 34 Teeth - 10mm 36 Teeth - 6mm There is an STL and a STEP version, the shape is the same.
This is a placeholder you can print and/or incorporate into your models in place of an ISD1820 recording/playback module PCB. Useful for planning or test-fitting the module into your prints or other projects. There are many variants of…
This model is a bracket to mount a Commscope (formerly Arris) Touchstone CM8200 Cable Modem to an IKEA Skadis pegboard system. This modem is commonly used by the Australian National Broadband Network (NBN) for Hybrid Fibre Coaxial (HFC)…
This is not a mod for the faint of heart, it requires an almost complete disassembly of the printer base frame. And probably a lot of swearing and frustration, but I am quite pleased of how it turned out. I am marking it as a work in…
This tool is a perfectly snug fit to safely remove fuel filter on a Kubota Loboy Diesel Generator and B8200 Tractor without damaging it. 3D PRINTING SETTINGS 0.15 100% Infill PETG
The engine on my brewster buffalo broke as i was building it so i had to model and print a new one
model - PETG , vrstva 0.15 mm varrianty ASA,ABS,PA,PC…..
Bracket to hang the long Ryobi OPP 1820 on a wall. Room for both the tool and the extension pole. No supports needed.
Like Bryan Crow I wanted to rack-mount my Arris Surfboard SB8200, but I don't have a full-sized rack only a 10" mini-rack. Since his model is designed to be assembled, I redesigned the front-plate to be a one-piece mount appropriate for…
Since the design of my Screwdriver holder is going really well, I wanted to expand on other tools as well. First the Flashlight an now the chinsel holder. Hopefully you need it as well. If you want you can add a heatinsert for more secure…
Remix for the Sage/Breville standalone coffee grinder (Model BCG820 BSS) of a great desing by @Simbungu. The screws go too low in this grinder and you can't tighten the inner part to the base, so it keeps unlocking. Altered the dimension…
Dosing cup for Sage Smart Grinder (BCG820 BSS). Holds up to about 45g of coffee beans which means I can use this for my espresso and pour over grinds. Easy print.
GBS 8200 RGB to VGA Converter/Upscaller Box. Two holes at the back: one to allow for an alternate power cord (I use a USB power source) and adding the possibility of mounting a micro USB connector PCB; second hole for an input cable (I…
Wrist rest for Ajazz Ak820 Pro. Printed with Centauri Carbon: White PETG No supports 0.2mm layer height Could also work on other 75% keyboards with 20mm height and 327mm lenght Split it in half in the slicer like i did, if you have…
GBS 8200 RGB to VGA Converter Box extended to the right so it can fit a NodeMCU ESP8266 chip to use with the gbs-control custom firmware. Also room for a 6pin DIN sock and a switch which I use to turn off the CFW if required This was…
Design After seeing Voultar's install video of this, I had an idea to make a housing for it myself, which was inspired by original cocktail arcade cabs. Video can be found here: https://www.youtube.com/watch?v=1AVXhiTlmgo Hardware Most…
GBS-8200 RGB to VGA Video Converter Board Case with 6pin DIN & Wemos D1 Mini Wifi Designed to house the Wemos D1 Mini to use with the customer firmware https://github.com/ramapcsx2/gbs-control Cut-outs for all the connectors including…
I modified Modellaner's design. I aligned the openings in the front of the case for the Component RCA Jacks (and vga port). I moved the SCART Port as far back on the case as I could to help it clear the RGBS Header internally, so it…
This is a mount for a DS18x20 sensor for ventilation temperature monitoring
Simple information plate Print Settings: Layer Height - 0.3 Infill - 20% Walls - 2
A tray for the ICON 10 in. Pliers Wrench [58200] There are options for stackable and nonstackable with both small and medium tolerances, as well as basic non-gridfinity trays
Coupling for microwave oven TEKA ML820BIS. The coupling on my microwave oven broke (it split where the motor
An K8200 / 3Drag enclosure for the RepRap Full Graphic Smart Controller . It was my design goal to achieve a solution with as few components as possible and preferably without screws. In the design process, my goals were achieved, but the…
This is a replacement part for the aforementioned headphones. It reuses the original screws and (when done carefully) can be installed without re-soldering the cable with its many flimsy wires. As you can see in the photos, its not a…
3D Printed enclosure for RTL2832U + R820T USB SDR if you have lost original one or want to shield it better. Power LED is visible through top hole. Easy to print and assemble. 8 x M3 bolts are required.
30mm fan mount for the All-Metal E3D v6 Hot-End to Velleman K8200/3Drag standard filament extruder. I liked the original fan duct and mount from E3D-Online and wanted the Hot End to mount on the original K8200/3Drag extruder using the…
This is a base setup to create modifications on this printer. I converted many parts from the OBJ model of http://www.thingiverse.com/thing:203292 but, many of them have been measured by hand. It have been made on Catia V5, aprx 20 hours…
Dieser 3D-gedruckte S-Haken dient als Ersatz für das PLAYMOBIL-Teil 30 22 8202 , das in der Falkenritterburg (6001) und möglicherweise in weiteren Sets verwendet wird. Der Haken wird für bewegliche oder verbindende Elemente der Burg…
Podstawka do miernika oraz pojemnik na kable i końcówki A stand for the meter and a container for cables and terminals
Replacement foot for SK-8820 Lenovo/IBM keyboard. Fits perfectly on my keyboard, even has that nice click Prusa mk3s 0.4mm nozzle 0.2mm layer height 100% infill Print with supports for the locating pins Shown printed in PETG but should…
Imprimir el fuelle en TPU sin soportes. El resto de piezas imprimir en PLA o PETG. No requiere soporte. Imprimir a 0,2 de altura de capa.
This part broke on my microwave and a replacement is about ~$60 here in Canada (slightly cheaper if if I order it from the US). I decided I would print my own, and hopefully others can use this as well. My microwave is a KCMS1555RSS but…
This is a K8200/3Drag frame mounting clip with locking screws. It is based on my redesigned of the K8200 Frame Wire Clip On . Next step will be to use the clip in other designs there could benefit from the more secure frame clip. This…
Tece -Entnahmewerkzeug Duschstab Artikel-Nr. 9820422 Das original Werkzeug von Tece bricht sehr leicht ab, deswegen habe ich selbst nachkonstruiert, um es jederzeit neu ausdrucken zu können.…
This is my 2nd upgrade of the K8200 3D Printer. It will transform this printer as a Prusa Mini. Part 000425 : Planetary gear, 23 teeth, 0,85 modulus
Flexible mount for the Digital Multimeter to keep the hands free. It is a holster and I use it with my mount system: https://www.thingiverse.com/thing:4110316 But it can also combined with any GoPro compatible mounting parts. I've…
Use the Skadis T-Nuts and some M2 screws for mounting You also need 1x 6x3 magnets and some glue
This is a case with an 80mm fan mount for the Bigtreetech SKR V1.3. You willl need to get two M5x12mm screws to attach it to the K8200, four M3x10mm with matching nuts for the mainboard and four M4x8mm to screw the fan to the cover. You…
Mounts with two 4,5mm Screws.
Spacer + T-slot block to mount things with 3 mm distance to the alfer coaxis 27,5 aluminium extrusions. Use M3 screws and nuts for the recommended M3 Version or 3,5 to 4 mm spax screws for the not recommended standard version. 2018-01-16:…
K8200 and 3Drag filament guide with one bearing. The parts can be printed, except for the bearing and the countersink wood/plastic screw 3x25mm. Update: Version for both bearing 6000ZZ and 608ZZ (skateboard bearing). The larger bearing is…
Eurocell CR8207 conservatory gutter bracket. This item is discontinued hope it helps I have made it a bit stronger than in the pics
Edit 12/06/19: Added Pictures of the finished solution. I have been looking for a great way to make the Z axel go up and down. I have tried a DOZEN designs and none where what I was looking for. Now I have designed my own one and it is in…
Fiat part : 182063280 Compatible with : Fiat Uno, Fiat Fiorino, Fiat Premio, Fiat Elba, Fiat Duna Important : Print horizontally, as per the stl file for better strength.
This is my 2nd upgrade of the K8200 3D Printer. It will transform this printer as a Prusa Mini. Part 000424 : Sun gear, 20 teeth, 0,85 modulus
Třeba se to někomu hodí . CNC Masturn 820 madlo pro koníka .
Simple K8200 and 3Drag frame snap on clips to hold the wiring as a replacement for the nylon strips. Based on BVD2e's model http://www.thingiverse.com/thing:444323 with few modifications. Update: Added variant with three profiles and STEP…
Hello dear maker! after a long search on thingiverse i've found this nice fan: http://www.thingiverse.com/thing:814286 . The problem i encountered was, that there wasn't any holder(for a K8200 / 3drag) for this fan at all! So i've decided…
IWS-2820/IWS-2412 holder for HoneycombStorageWall
Upgrade parts for the K8200/3Drag extruder to enable use of 3mm flexible filament such as NinjaFlex and TPE (shown in blue). Teflon tube in each part ensures a non stick filament feed. >> If you like it, please leave a like, rating or a…
The original kit has too much wobble on the Z axis, resulting in shifting and uneven layers. This design is for a minimal but rigid Z axis, using a trapezoid lead screw. There are only changes to the original design, where needed. The new…
This simple construction are for upgrading your K8200/3Drag to GT2 belt on Y axis. It is a direct replacement, reusing the original mount screw and holes, adding the missing belt tension. For complete upgrade of Y axis to GT2, you need:…
Qlima dehumidifier models D820 and D825 house a Hepa filter and will clean your air and remove moisture. Unfortunately these filters cost around 40 euro's and have to be replaced within months if the dehumidifier is used in a dusty…
Réceptacle en 3d pour l'imprimante DNP ds820 a glisser sous l'imprimante
If you are using the 16T GT2 pulleys on a K8200/3Drag The belts will collide, and the Y belt will rub on the smooth rods of the X axis. To provent this, you can use this mod that raises the Y axis by 12mm. This way the Y belt will be…
///// I highly recommend printing&building Thing: 6387573 (updated version by "markeno") ///// I've designed another case for the GBS control unit. You will need 2x M4 x 10 mm screw with nut (for SCART connector) 2x M3 x 10 mm screw (for…
This is a replacement switch button for Oster Cordless Electric Corkscrew/wine bottle opener model FPSTBW8207-S Installation details can be found in Installation Instructions Print Settings Printer: Creality CR-10 Rafts: No Supports: No…
I have made a microphone array for measuring polar patterns and whatnot, and it is important that the gains of all the mics are matched. Tuning them is an elaborate procedure, yet it is so easy to bump a knob off of the tuned position,…
infill 100%, PETG for flexibility, apply epoxy only on middle part to retain the flexibity of side parts, see photos
I lost one of the pads for my old 2" quick grips. I modeled this pretty quickly so it's not perfect. It could use a few tweaks for a better fit, but it works well enough as-is. Print with TPU! (or other flexible filament) I printed at…
![ICON 10 in. Pliers Wrench [58200] (Gridfinity)](https://media.printables.com/media/prints/cf66cf2e-2b6c-4c20-a405-9dc2a0d2615a/images/10717290_f86dd5e2-a981-4040-bb1c-6a079b4e1ed8_2d4bf60d-c192-4704-b42a-5466183dd82f/icon_10in_pliers_wrench_58200_screenshot.png){kind=icon}
