Counting matching models…
This is my version of a 3D printed clock. I designed it entirely in Fusion 360 and it has now been running for a couple of months. Time keeping is very accurate. It uses a Nema14 stepper motor, a TMC2208 driver as well as a Wemos D1 mini…
PPW Mk1 Self-Adjusting Gripper Plywood/Panel Carrier Clamp Effortless Panel Transport: Experience unmatched convenience with the PPW Mk1 Gripper Clamp, designed to streamline your workflow and make panel carrying a breeze. Its innovative…
I have recognized that the adjusting with a credit card, as described here https://help.prusa3d.com/en/guide/how-to-adjust-the-height-of-the-m-i-n-d-a-sensor-mini_154547 , is not good for Super P.I.N.D.A because the Z-Live will be…
🌟 Presenting our newest creation: The Dune Sandworm Coaster! 🐛✨ Inspired by the movie of Dune, this 3D-printed coaster adds a touch of sci-fi into your everyday routine. Say goodbye to ordinary coasters and embrace an interactive…
Just another vertical laptop stand... but this one has a flexible hinge at the bottom that adjusts to the thickness of your laptop. Nothing screams "I'm a maker" louder than this simple piece of 3D printed plastic. The thin layer in the…
The Honeycomb Windmill - Self adjusting hexagon turbine YT Short Action Beautiful Windmill with a unique honeycomb Propeller Design Self adjusting to wind direction through the Tail Blade 100% printed, no Screws or tools needed You can…
Adjusting Ring / Shaft Collar 8mm, 10mm using a M3 Nut and Bolt. Choose a 12mm bolt, 10mm may be sufficient. The 8mm one will fit around TR8 / T8 Spindle like shown in the picture. Print instructions Category: 3D Printer Parts Summary…
Violin wall hanger / mount for acoustic violins of all sizes, and it should work with violas too. It has a rotating fork that automatically adjusts its angle to grip the violin by the neck. Mount the base to the wall using a single screw…
Self-adjusting height DJ laptop stand
The parent system is neat, but I needed a way to mount these IRWIN wire strippers: https://www.amazon.com/IRWIN-VISE-GRIP-2078300-Self-Adjusting-Stripper/dp/B000OQ21CA Additionally, I found some of the sidepiece flats and pins in the…
For KTM/Husky bikes, the chain tension is measured at the end of the upper chain guide and the distance between the swingarm and the lower side of the chain links shall be between 55mm and 58mm. This guide needs be positioned behind the…
A slightly overengineered solution to get your phone mounted somewhere, f.e. in your car. This mount grabs your Phone from both sides, it will fit phones approx. 105 mm - 50 mm wide. You will need to print: 1x - body 1x - spur gear 2x -…
i didnt saw anny self adjusting coasters for free so i thaught why dont i make one for free?
With numbers which makes them easier to identify, especially at night. I printed my set from PETG, 4 perimeters, 100% infill. Might need a bit post processing to touch up any PETG stringing and smoothen the numbers.
A self adjusting spool for anyone using many different Makers of filament and hanging them on a pole above or around the printer Print instructions This print requires no supports and is already oriented. Can be printed in any material…
This is a basic tool used to adjust the Compression on a WP6500 cartridge fork. It is very handy since most bikes you would need to remove your handlebars in order to adjust with a flathead screwdriver. This is a flathead tip on a disc.…
I recently built a crude rail hinge to get repeatable square cuts on my modified Masterwork table. I was however not happy with the adjustment mechanisms of the first iterations. Looking at the market, there was no suitable acessory for…
IRWIN VISE-GRIP Wire Stripper - https://www.amazon.com/gp/product/B000OQ21CA/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1
Shower head holder with adjusting wheel designed for wall mount or to shower cubicle (dimension of hole center 48mm) designed for 4mm screw with 8mm head size for adjusting wheel is used M8x50 screw and nut print black parts with TPU…
Adjusting cupholder i made for my sons bunkbed. Feel to modify and please share if you do also 4mm bolt works perfect or you can use zipties.
Adjusting Screw for Lechuza Balconera planters like the ‘Balconera Cottage 50 granite’ ( https://www.lechuza.world/promo/balconera-cottage-50-granite/15602.html ). The adjusting screw has a wider head than the original. Thanks to Lechuza…
The adjusting knob for changing head sitze of my (no-name) welding helmet broke. The replacement supports the pins more. The original knop also had 4 pins, but they were only connected at the bottom. The pins on the replacement are…
Print with support the following parts: back bottom end I advise printing the vent holder with TPU, or any soft material to avoid scratching your car vents. You can add a rubber band so that it stays open when your phone is not in place.…
This paper towel holder allows the person in need to tear a piece of paper with only one functioning hand. IT REALLY WORKS =) Only 60 grams of filament! !!! Use tube-o-matic for the auto-resizing tube. Diameters of 44mm to 47.5 should be…
Fixation every 6 degrees. When using screws with M4 threads with a pitch of 0.7, adjustment is made in steps of 0.0116 mm. Print using variable layer height so that the layer on the teeth is 0.1 or all 0.1, but it is long. Post-treatment…
Geteilter Stellring / Klemmring, Durchmesser aussen 75 mm, Durchmesser innen 48 mm, Höhe 15 mm. Ein Teil mit Gewinde M6, ein Teil mit sechskant Ausnehmung für M6 Mutter. Benötigt werden zwei Inbusschrauben M6 x 25 und bei dem Gegenstück…
Fits either adjusting wheel on 10HP Craftsman Table Saw
Key for adjusting sharpness of Raspberry Pi cameras V2.1 original lenses. This part can fit and can be hold in the window of some existing cases. Otherwise, it can also be manually holded. Layer height 0.1 or 0.2 mm, infill 15-30%
This is a remix to allow phones of different widths to be used to control Klipper on an ender 3. A rubber band is used f
knob for axles with a diameter of 5/6mm. You can ask me for other sizes or simply scale the whole thing in the slicer.
for the LEE AUTO-DRUM POWDER MEASURE
This is a replacement for plastic part of Bosch adjusting device 10009551 (for fruit pulping attachment). There are two Bosch fruit pulping attachment models that use this part : Fruit pulping attachment MUZ8FV1 , with Spare part: 0103…
If you want this gripper go here : this here is only the printed screw that is used it in. This is just an addon to the nice panel carrier grip. Finding the metal screws in Europe turned up to be quite expensive and ridiculously…
Frigidaire Washer/Dryer Combo Adjusting Bracket 5303212877 Made this discontinued part for someone but they didn't end up buying it. Please help me verify the fit! Part Information This washer suspension spring adjuster insert (part…
Friction fit soft jaws for QUINN 7 in. Self-Adjusting Pliers from Harborfreight.
Honeycomb wall holder for QUINN 7in. Self Adjusting Pliers
I made it out of Tough PLA (Bambu) 0.1 layer height, printed in solid pieces. No support needed when printed in Bambu Lab X1 Carbon.
As an upcycling project I've designed this wall clock from an old LED lamp. It's based on an wemos d1 mini with tasmota firmware. See the documentation in download.
this ratcheting toothpaste squeezer is releasable so as to remove the tube easily. just need press on lever and hold while releasing/unwinding the tube. the slot piece where the tube goes in self adjusts and tightens to the amount of the…
This is a parallax adjustment wheel for an Athlon Cronus GenII rifle scope. It has an outer lip that stops how far it can be pushed onto the turret. This leaves the yardage numbers easily seen. Mounting is sized for an m3 screw and nut.…
This is a parametric/customizable knob for M8 screw used in office chair. Print instructions Category: Replacement Parts
Modified idler tensioner that can be adjusted from the top rather than awkwardly from the bottom as the original did. It also has an embedded square nut (M3nS Thin Square Nuts/DIN562) that holds it's place much better when unscrewed. The…
Holder/stand for iPad Air or any similar sized tablet. The holding area has 15,5cm x 15cm. What will you need 4x M3x20 screws 4x M3 nuts Super glue Print instructions Used material : PETG or PLA Layer height : 0.2mm No supports needed for…
Spare part - insert between roller and rod for roller IKEA MAGASIN 764.856.05 https://www.ikea.com/cz/en/p/magasin-rolling-pin-76485605/ The original part broke, so I made a new one. I also added an extension option to set the thickness…
The optics of astronomical reflecting telescopes must be adjusted exactly. Many people use alignment lasers for this purpose. Of course, the laser itself must be centered just as precisely. My laser was badly adjusted at delivery, so it…
This self-centering filament spool holder can be produced only with a 3D printer. The roller compornents can be positioned anywhere and moves to adjust to the filament diameter. This holder fits the IKEA 365+ 10.6L box. Please check the…
I designed and made it for my Hi-Brew coffee. But I think it is fit for 58mm portafilter due to it is adjustable. Its useful for filling, tamping and all the espresso needs you might have.
This is a part / component intended to be incorporated into larger projects. The basic mechanism is print-in-place, but to remove backlash/wiggle, it's recommended to print and slide in a tension plate To use it, pinch the two side plates…
Self-adjusting headphone stand that slides onto your desk. Should fit most standard desk sizes, but measure before if you're unsure. The rubber pads are 2x6mm. Let me know if your desk requires a different size! Printing Walls: 4 Infill:…
This is a replacement part for the BMW G650GS or similar. This is the rear spring preload adjustment wheel holder. For me, this holder simply broke one day. The spare part is designed a little more intelligently and lasted over 2000km on…
Screw mounted holder for irwin wire strippers, I printed in creality petg on my p1s, no supports needed.
Replacement foot/boot for a Bosch fridge-freezer. Fits the 13mm hex bolt and provides a floor-contact point. Extended sides enables adjustment of the foot/leg height without the need for a spanner. I printed in PLA and with the ‘dome’…
Hole is little bit large. Put superglue inside the hole and attach it.
ESP32-CAM Lens Adjusting Tools for OV3660 These tools are for breaking the lens factory glue seal and also adjusting the lens focus. The ESP32-CAM lens comes glued in place from the factory. I found it very hard to break the glue bond…
These are part of a research project by MOST (Michigan Tech Open Sustainability Technology Lab) aimed at creating a customizeable pair of glasses that can utilize self-correcting lenses. These lenses allow the user to dial in the…
for this idler, it used a new idler pulley and used a extra M3 20mm bolt sized for the idler is also included in the cad what to print 2 inserts for the idler pulley a idler housing. including 2 versions, make sure you print the right…
Adjusting Pin for Roller Shutter Motor Adjustment Tool Tubular Motor
Note : This print includes a TestRing section which can be printed to test the fit of the complete post cap. I created this print to replace a post cap which was smashed to pieces (see photos) when a tree limp fell on my fence. Note the…
Tiskl jsem v PLA výška vrstvy 0,13 segmenty 3 a hustota 18 bez podpěr..
Universal & Self-Adjusting Filament Spool Holder lightweight, and hardware-free filament spool roller designed for maximum stability, ultra-low friction, and ultimate flexibility. Built with a low center of gravity to keep your spools…
I broke the old one so i made new
I need to stack some laptop chassis - and with the original feet, they tend to slant a bit to the front side. Since over the back feet the laptops are 17.75mm high, and over the front feet it's 14.5mm, I adjusted the height of the…
More damage resistant version of the knob. Original cap fits well. Recommend print at 50% infill
Adjusting key is needed when adjusting regulator pressure. More precise adjustment and no scratches on your gun. Additionally needed items: -6mm steel rod, length 50mm (optional) -2 pcs 2 mm steel rod length 12 mm
thought of this tools after watching others on youtube make spheres using a 3 head machine. I thought I could print a sanding tools that could form a perfect sphere from wood using only a drill. the heads mount with m4 bolts, no incerts…
Adjusting Leg Screw M20x2.5 Key 24mm / 6mm nut ø24 x 22mm Category: Hand Tools
Adjusting Tool is needed for Sunblind setup after repair
Detailed 3D printable Chibi Gojo Satoru Adjusting Blindfold Smirk figurine, ready to print on FDM in PLA. Usage & Links Personal use: print freely. Commercial/digital redistribution is only allowed with a valid Patreon license:…
This pin is used to adjust Primal Gears brand belt mount, to fit various belt widths. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Filament: Plasty Mladec PLA Category: Sport & Outdoors
Вам понадобятся втулки с резьбой 3 мм и винты. На фото видно, куда вставлять резьбовые втулки
These are best printed in TPU. The self-adjusting pliers are another incarnation of the Robo Grip pliers from the 80's. They only require one hand to operate. The jaws are flat and serrated, and operate in parallel. These Kobalt ones also…
This is a spare adjusting wheel for Kern Swiss Auto Level Surveying Instrument Model GKO-A This is an very old auto level Instrument. Perhaps someone has the same instrument and also needs a replacement. Printed with ASA from Extrudr.
Gear driven self adjusting wrench with NutGrab(TM) self locking technology. Adjustable from 23mm-1mm Glue assembly at the tabs and one M4x12mmcenter bolt and M4 heat insert.. M4 nut and bolt will work to just melt bolt through hole of…
The adjusting gasket was too small and hard to grab, I made this to friction fit I made the tolerances pretty small .2 or so, if you still find it too tight to press yours in may want to calibrate your printer. I printed this in ABS, PLA…
this has a mechanism that auto adjusts the roller distance to squeezer inlet so that you have the shortest length of tube end to insert into the squeezer inlet and and through the roller to start winding/rolling the tube up. roller/winder…
This mechanism allows you to easyly adjust the tension of the strings I used 0.08 mm layer height for the screws and nuts because of the M5 threads. For screws I used brim Printed on Prusa Mini+ from PETG Regshare
Při jízdě na sjezdovce jsem si rozbil čumák a ztratil utahovací kolečko z helmy Wedze. I had a crash on SNB and lost a adjustment wheel of Wedze helmet. My print: PETG, Nozzle 0,25, 0,12layer, 5 outside layers, 20% gyroid, no supports.
A knurled extension for a 5/16ths nut for quickly repositioning spools on a roller.
Adventurer3のワークサイズ150mmに合わせたピント合わせと画角調整用の高さスケールです。 10mm間隔で穴が開いていて、50mm間隔で大きな穴が開いています。 タイムラプスの撮影にご利用ください。 A height scale for focusing and adjusting the angle of view according to the work size of 150 mm of Adventurer3. There are holes at…
The wheel for adjusting the inclination of the backrest broke and they did not have a suitable spare part anywhere.
Gridfinity holder for the Proform Holley Float Adjusting Tool. Yes, it is very simple but this was very first try at making a custom holder in TinkerCad. It does what I wanted it to do, keeps my float adjusting tool from floating around…
Small 60x20x7mm hole 6mm clamp. it can be rescaled. made in fusion 360. Printed in Pet-G at 20% infill 4 walls also works with PLA and ABS. Desinged to fix models position with screws in place, to wooden base. usaly for cnc or…
This is a very simple model I made in less than 10 seconds. My old vacuum cleaner uses bags that connect to the hose attachment with a rubber lip. When attached this lip does not have a great seal unless pulled up onto the connector. it…
Wanted a place to store this small Floyd Rose intonation adjustment tool and the associated allen key. I don't use it often, but it is nice have it and the allen key in a dedicated spot. They sell this tool on Amazon as well as other…
This is a spare part replacement for the direction adjusting lever of my Bosch GSR 18-2. Original Part-No. 2 609 101 009. The part is mounted in many other Bosch tools. Printed with Prusament PETG. Due to the sloping surfaces, I printed…
See pictures for the reference of broken knob. Added walls act as a cover for the spring, held in place by nut.
The "barre 5mm x 40mm" must be printed twice, as well as the "fixation socle, vé double". The rest should be printed once. And a little tip for assembly: I recommend looking at the pictures to avoid getting too frustrated.
Best printed with the slot on the bed for better structural rigidity on the heavy use faces. Recommended filament PET-G
UPDATE 2: Added a spring-loaded insert that will adjust based on your container's width! You will need a spring (10 mm in diameter, length based on your preferred "stiffness" of the clamp) and a bolt for it to work! UPDATE: Increased the…
Self-adjusting headphone stand that slides onto your desk. Should fit most standard desk sizes, but measure before if you're unsure. The rubber pads are 2x6mm. Let me know if your desk requires a different size! Printing Walls: 4 Infill:…
This is a spare part replacement for the direction adjusting lever of my Bosch GSR 18-2. Original Part-No. 2 609 101 009. The part is mounted in many other Bosch tools. Printed with Prusament PETG. Due to the sloping surfaces, I printed…
Při jízdě na sjezdovce jsem si rozbil čumák a ztratil utahovací kolečko z helmy Wedze. I had a crash on SNB and lost a adjustment wheel of Wedze helmet. My print: PETG, Nozzle 0,25, 0,12layer, 5 outside layers, 20% gyroid, no supports.
Adjusting key is needed when adjusting regulator pressure. More precise adjustment and no scratches on your gun. Additionally needed items: -6mm steel rod, length 50mm (optional) -2 pcs 2 mm steel rod length 12 mm
The "barre 5mm x 40mm" must be printed twice, as well as the "fixation socle, vé double". The rest should be printed once. And a little tip for assembly: I recommend looking at the pictures to avoid getting too frustrated.
Gear driven self adjusting wrench with NutGrab(TM) self locking technology. Adjustable from 23mm-1mm Glue assembly at the tabs and one M4x12mmcenter bolt and M4 heat insert.. M4 nut and bolt will work to just melt bolt through hole of…
PPW Mk1 Self-Adjusting Gripper Plywood/Panel Carrier Clamp Effortless Panel Transport: Experience unmatched convenience with the PPW Mk1 Gripper Clamp, designed to streamline your workflow and make panel carrying a breeze. Its innovative…
