Counting matching models…
This is a remix of the other model, incorporating splined inserts and matching splined halves to allow for 45 degree incremental rotation. No threads, assemble with #10-24x2.25" socket cap screw and nut. Version 2: Has deeper socket cap…
Einteiliger Lichtschrankenträger für Birdfeeder
The Feeder Stop Switch .223. It fits now the large DAA gen2 Spring and fits with the DAA The Mr.BulletFeeder Die assembly. And it's only one Part.
Ein verbessertes Teil, das beim original Model nicht so gut gelungen ist.
A simple lid to avoid falling bullets out of the tubes of Mini Mr. Bulletfeeder if you are not holding it straight up. Just put the lid on, and never worry about having bullets all over your floor again. Also included is a base for two…
An OpenBulletFeeder shaft adapter for JGY370 motors, or any motor with a 6mm output shaft containing a threaded M3 hole. This design does not have an internal flat for the D-shaped output shaft. Clamp it to the shaft using an M3 screw…
I really liked madmac10's Mr. BulletFeeder controller mount for the XL750 (assume it would work fine with the XL650), and printed it for my XL750. I also have a RL1100, and the casefeeder support pole is square-ish, 25.99mm x 25.62mm, so…
Einteiliger Lichtschrankenträger für Birdfeeder
This is a simple bullet feeder adapter fitting many bullet feeder dies, but specifically designed to couple the GPmax bullet feeder die with the standard lee tubes (the same used for the cases). Prining it with the larger side up and no…
I was too lazy to wire up my OpenBulletFeeder motor and sensors when I got them, but still wanted automatic bullet placement, so I did up this little knob. Not as good as a motorized bullet feeder, but a whole lot faster than setting each…
Mit der originalen Flip Ramp hatten wir die Probleme das die Kaliber .45 Geschosse teilweise aus der Collector Plate herausgeschubst wurden oder an der Flip Ramp geklemmt hatten so das der Motor gestoppt wurde. Mit dieser Flip Ramp ist…
Es ist das Verbindungsstück das den Bulletfeeder mit der DAA Feder verbindet. Bei Kaliber .45 hatten wir des Öfteren klemmende Geschoße, da diese nicht schnell genug, die sich drehende Collector Plate verlassen haben. Mit diesem…
This is a stand or wall mount for the magazines. I made it to use it as wall mount. so the don't use space on my shelves. The holes are perfect for 3 x 25 mm screws. Even when the srew head sticks out a good bit it does not matter. Print…
Cable clip for Dewz Bird Feeder rev B bulletfeeder. Designed to fit on 1.2x14mm spring.
There might be like 3 people in the world who need this, but if you want to store your extra DAA Mini Mr. Bulletfeeder loading tubes on your storage wall, this should do the trick. I have one version that sticks out straight and can print…
Drop Insert 45ACP, remix by GerHART & Dewz.
Uns ist aufgefallen das im Bulletfeeder teilweise viele Geschosse unten liegen bleiben und rollen aber nicht in die Löcher der Collector Plate fallen. Mit diesem Knubbel, der in ein Loch der 9mm Collector Plate passt, werden die Geschosse…
Diesen Adapter kann man auf jede 15mm Feder schrauben und dann mit meinen Bullet Stopswitch verbinden. Es ist seitlich ein Loch vorhanden um eine Gewindebuchse hinein zu schmelzen, damit man eine Schraube zum arritieren am Stopswitch…
6.5 V2 Creedmoor Plate. Collating these very long boat tail 6.5mm are a challenge, they like to ride above, angle your feeder at 45 Degrees, the more in the collator, the better the result. For the original, smaller, OBF. Clutch plates…
2 part connector to join a 1.2x14mm output spring to the Drop Insert. This has been designed to work with the thread of @GerHard_2467389 replacement Drop Inserts -…
223 Plate. I have made this by request, I have not tested it. It appears to work great, check out the video. Based on my 6.5 Creedmoor Plate. https://www.thingiverse.com/thing:3547180 Print 0.2 layer 0.4 nozzle 4 Side perimeters 3…
This is an adjustable and lockable 1” pipe mount for the openBulletFeeder. There are improvements from the one included in the openBulletFeeder. The Bullet Feeder mount side is modified from the OBF file, so the usual fitment issues from…
These are both Flip plates for 6.5mm, will flip your nose down. They should work with just about any rifle caliber, but I have not tested it beyond 6.5. This works with my 6.5 Collator Plate https://www.thingiverse.com/thing:3547180 These…
308 Plate. I have made this by request, I have not tested it. Based on my 6.5 Creedmoor Plate. https://www.thingiverse.com/thing:3547180 You will need to use my Flip plate/s for the nose down bullets.…
6.5 Creedmoor Plate. Collating these very long boat tail 6.5mm are a challenge, they like to ride above, angle your feeder at 45 Degrees, the more in the collator, the better the result. You will need to use my Flip plate/s for the nose…
This is a modification of the electronic mount from AmmoMike83's (all credit to him) OpenBulletFeeder, https://www.thingiverse.com/thing:2504314 , The Bullet Feeder mount side is modified from the OBF file, so the usual fitment issues…
The 6.5 Creedmoor Drop Tube Big Switch Small Spring from AmmoMike83's (all credit to him) OpenBulletFeeder, https://www.thingiverse.com/thing:2504314 , The one included in the project has the wrong ID of 0.258. I have corrected the ID,…
Enclosure for Dewz Bird Feeder rev B bulletfeeder PCB. Gives a bit more stability to the potentiometer knob. Replaces the PCB Spacer. Designed to use 2x M3x6 BHCS screws + 2x M3 heat inserts to attach the lid. Printed in Polymaker Pop…
