Counting matching models…
Full set of couplers to add an additional lack table to the original lack enclosure. Print instructions Printer Brand: Prusa Printer: I3 MK3S Infill: 15% Filament: Prusa PETG
I redesigned my 40° coupler from the ground up! The Fusion360 design is now more parametric, so if you want to mess with the angle, get the source here! https://a360.co/2BwCLdH It's also shorter, and has a smaller footprint in general. It…
We were so keen to get installing our UniFi Protect G5 Dome Ultra cameras with their shiny backboxes, then realised that getting hold of G ¾"-threaded Conduit is a bit of a pain in the UK. We wanted to use standard 20mm PVC conduit, which…
My bicycle uses S&S Couplers for 1-3/8" tubing. Through trial and error, I made a protective cover. This cap screws over the tubing “good enough”. Thread Type: GM Metric Profile Size: 42.0 mm Designation: 42x1.5 Scaled 98.81% X and Y only
This is a very simple coupling clip that can fasten two MatterHackers 1KG spools together. Installing these are difficult due to the small spaces involved and the sharp unfinished spool's inner walls. So do take care. Caveat: Due to…
Coupler designed for an above-ground graywater drainage line. We have a tree and a few other things we like to indirectly water and this makes it possible to use cheaper PVC to make up the majority of the length. Best printed in ASA, but…
It's not a precise nor detailed model. It has simply 4 parts to show you the basic principle of a Janney coupler. Print in the position I posted. It's basically support-free if you print it small. Will need to add some support with the…
The centauri carbon has a chamber thermistor that is mounted to the frame with a steel screw and plastic spacer. The steel screw is thermally conductive enough to significantly skew chamber temperatures colder. I found that the built in…
Gardena Male coupler standard 3/4 BSP
just a simple reducer from 25mm to 20mm for electrical PVC Conduit, printed in PeTG 60mm/s no supports fast simple. just print it! its quick :)
**See new modular version https://www.printables.com/model/512560-modular-plant-trellis-coupler Initial version 130w x 199h mm plant trellis, can link 3 or 4 together. Coupler allows them to stack
Uses M3x12 hardware to join 2 shotgun magazines together. Fits 5 or 9 shell mags. No Supports. 12GA semi automatic. Print 2 of these!
½ inch pipe coupler. Printed with 0,16mm layer height. Be sure to check out my other piping models!
1-1/2" to 1-1/14" [1.5IN to 1.25IN] Pipe Reducer/Coupler/Adapter (No Supports) No Supports required. Used to couple and reduce 1.5" to 1.25" pipes or tubes. 3 Inches of clamp space on each side of the adapter.
I swear by the Trianglelab filament runout sensor, but its one shortcoming is that it doesn't grip a bowden tube at the entry/exit, which means it's a pain in the ass for feeding / removing filament if you don't hold the whole lot…
Basic mechanism for forced coupling with elastic lock
I made this to transfer the last bit of soap from a bottle into another one without spilling any. It has a funnel that makes sure none will leak out and holds the bottle tight enough to make sure it doesn't fall out. It also turns out it…
Dust Splice Coupler Adapter - from 4" PVC to 4" Dust Hose. As mentioned, this is styled after POWERTEC 70123 O.D. Splice, 4", Black, available here* , yet tweaked/shortened to make it print more quickly than a 1-to-1 mimic would print.…
Made an 1/8" imperial equivalent of M10 because I had those lying around.
PC4-M10 PTFE coupler with imbedded M10 nuts. I got tired of the printed versions failing after a while from plastic fatigue and designed this. My printer is out of commission right now, so I haven't had a chance to print it yet, but here…
Update 11/15/24: It was made aware that I did not include the PTFE connector that was used/fits with this adapter. Please see this amazon link:…
Replacement drive coupler for the dough mixer , the part sit between the mixer and the motor . i printed in PC with 6 walls and 50% infill. PLA should also work as it doses not seam to get hot,
Description This is the only case where 1+1 can make 1 but a better 1. Ever found yourself with pencils that are too short? With this tool you can join two pencils that are too short to create 1 of normal length, just squeeze the two…
I need to drive a load at high RPM using a smooth shaft 775 DC motor. My concern is the balance of such a coupler/adapter in addition to tolerating tangential impacts without slipping. While the collet like mechanism was inspired by RC…
Print two of these to join a flex duct through a screen! Designed for 4" ducting like this: http://smile.amazon.com/FO450-5-ply-Supurr-Flex-Aluminum-Ducting/dp/B00009W3H2/ref=sr_1_2?ie=UTF8&qid=1412923160&sr=8-2&keywords=flex+ducting…
This is an adaptation of another model which had a good idea but only supported the coupler on one side. I tweaked the item to extend the support length as well as re sized so that you can support the PTFE on both sides of the coupler as…
I've built the TZB MMU2S filament buffer which requires 10 PTFE couplers with R1/8 thread. In my setup, I want to be able to quickly connect and disconnect the five tubes, so I've designed this solution where the tubes are all clamped…
Introduction (Later improved model than this is here : Racetrack Tuner ) This is a capacitive coupler for tuning Short Loop Antennas (STL). It is an evolution from the ‘Patterson Match’ aka military loop from 1967, this is my fifth…
Can be printed in any suitable material such as PLA or PETG. I printed The inner part with PETG and the outer part with PLA. Supports are needed. I used PETG breakaway supports for the PLA and vice versa. A rubber band is needed for the…
Introducing the Cursed Connectors: BeamStream Coupler , the latest absurd addition to the Cursed Connectors series! This quirky model combines a garden hose with an E26 lightbulb socket, creating a unique and entertaining way to lighten…
This is a coupler to attach the tubing from the polybox to the prusa i3 mk3 filament sensor cover. Category: 3D Printer Accessories
A coupler nut that is compatible with PC4-M5 Couplers; the same type that is used in the Prusa Nextruders.
Introduction The racetrack tuner is a capacitive coupler for short transmitting loop antennas. The name is refering to its racetrack form. Racetrack Circus Maximus in Rome - maybe I should call it ’Maximus Tuner’ :-) For use by certified…
Color front panel to make text fluorescent on front panel. Text is made in classic frontpanel style with DIN17 font for professional look and feel. Add desired colour in the letter pockets before printing if your printer can handle…
Coupler for Kenwood MultiOne food processor. Model number which I own is KHH30. I printed test unit with PLA, but once it breaks I will go with PETG or ABS.
This is a coupler to link mirrotation device to 12mm button. See : The SolidWorks files are given so you can adapt the coupler design to other telesopes. What do you need : 3 x (brackets + base) 15 x Ruthex M3 inserts 3 x magnets (see…
You bought an autofocuser. It came with a bunch of couplers to mount it to your focus tube. But you only need one, and now you want to store the others. Store them with gridfinity!
I made this part 1mm higher and insert a cable hole. I made this because I want to use the magnet contacts with pre assembly cables. For me it was easier to mount
About I used hole in the doors of the Original Prusa MINI Enclosure as an entry point for filament PTFE tube. Moved handle for fingers a bit lower, and added magnetic coupler in there for s 6x2mm magnets, which are popular in gridfinity…
I designed a number of connectors with to make decorative fencing, railings and ladders etc. for use with the fischertechnik construction system from 6 mm hose. I'm pretty sure there are many other applications for your own projects. Some…
Update 11/15/24: It was made aware that I did not include the PTFE connector that was used/fits with this adapter. Please see this amazon link:…
A Printed flex coupler, the center flex section is a printed mold for silicone. I printed mine in PET-G. Coup.plastV2 and Shaft plug are printed together, to form the mold. As an alternative you could print the canter in TPU, I have not…
Made an 1/8" imperial equivalent of M10 because I had those lying around.
Remixed of the original M6 connector , allowing to connect 2 PTFE tubes using M6 quick release connectors. Both sides are threaded.
update: I just found an existing model in Scale I and II - obviously I previously did not find the proper search words. Still, that model is not functional (no threads) - see my " railway stuff " collection. I don't think a thread for…
Mod for the pico MMU from LH. Inward PTFE tube coupler is M10 version, outwart PTFE tube coupler is M6 version.
This part lets you use the official Bambu Lab PTFE tube coupler with the swiveling PTFE holder your A1 comes with. Good for having a direct reverse bowden to your filament dryer. Unscrew the original through the hole in the side of the…
I like the original designs filament cutter and the fact I can automate it. Though I couldn't reliably print the bowden coupler part. Anyway I manually load/unload the filament so it's better for me to easily plug out the PTFE tube. I…
Introduction The racetrack tuner is a capacitive coupler for short transmitting loop antennas. The name is refering to its racetrack form. Racetrack Circus Maximus in Rome - maybe I should call it ’Maximus Tuner’ :-) For use by certified…
This Coupler Hole Jig is an enhanced version of the coupler hole jig provided with @GunplaMark 's outstanding Ultimate Cereal Container Filament Drybox . It provides a more precise drilling location for the coupler than the original…
Lego Duplo and Connetix extended Connector/Coupler Material: PETG Perimeters: at least 3
A while back, one of my PrusaXL filament guides' coupler started popping off, and I saw someone posted a version that used PC4-M10 couplers (instead of the cheap metal Bowden collets). Around the same time, my PrusaMINIs had issues that…
Couples the shaft and pin from the input to the gear for the output
UPDATE April 24, 2026: I have published the third generation of my Coupler Cap for Cereal Container Drybox as Filament-Holding Drybox Cap . The new Gen 3 version grips the filament very firmly , and it has much smoother operation than…
The centauri carbon has a chamber thermistor that is mounted to the frame with a steel screw and plastic spacer. The steel screw is thermally conductive enough to significantly skew chamber temperatures colder. I found that the built in…
Extender for the A1 Mini to add another bowden tube running from a fry box.
This adapter (coupler) allows you to connect a Lego Technic 56x28 ZR Wheel (or any compatible Lego Technic wheel) to a TT DC gearbox motor (shaft Ø 5.4 mm). The design provides a secure friction fit, holding the wheel firmly in place…
THIS IS A WORK IN PROGRESS These are tested, I'm just too lazy to take photos This is not scale, nor do I claim it to be! It's merely “Close enough.” I'm just here to design funny big trains anyone can make, not rivet-counter-delight.…
This is my first ever functional design. I'm definitely not an expert, I'm still learning a lot about 3D modeling and printing, so this was a big practice project for me. It might have some small errors or issues, but it’s working pretty…
I've made this coupler for my Felder Hammer A3-31 jointer/planer dust collection. Main purpose was to create something mine because i like to desingn things :-) It was designed with glue-in insert, so it prints with just small support on…
This Improved Coupler Nut is a remix of the Coupler Nut from @GunplaMark 's The Ultimate Cereal Container Filament Drybox that now includes PC4-M10 Threads and a Flange for a perfect, secure fit with the PC4-M10 PTFE tube coupler. I used…
EN: BabyTrains - Coupler (Spřáhlo) 🇨🇿 Česká verze níže 📝What is BabyTrains? Story here . Overview of All Models on Printables: BabyTrains - Coupler (Spřáhlo) BabyTrains - Wheels (Kola) BabyTrains MINI - Bogies (Podvozky) BabyTrains MINI -…
Attelage type "Tension coupler" utilisé généralement sur le matériel britannique en 00, qui fonctionne mieux à mon goût que les attelages européens de type "boucle". Ce fichier s'imprime très bien avec une buse de 0.4.
Simple hose coupler and trash cap for the AC Infinity 6 inch exhaust fan Printed 100% infill, Petg, ABS 2-4 layers, tree supports Please leave a "Like", Thanks for downloading.
Can be plugged between hose adn accessories Is designed to rotate 360° Held together by 1.75mm fillament According to Einhell 36mm Hose. Hose fittings measure 35-35.5mm (conical friction fit) Print instructions: 0.2mm leigher height Maybe…
I wanted this because despite the filter on the printer I was still getting heavy ABS fumes. This just pushes onto the printer outlet, and the ducting is taped on like any aircon application. It's a simple design, I didn't get fancy about…
A coupler nut that is compatible with PC4-M5 Couplers; the same type that is used in the Prusa Nextruders.
This is a high quality modification of the original CORE One side handle for a PC4-M4 pneumatic coupler . The model has been adapted from the original CAD model released by Prusa. The resulting part has a high quality mesh unlike other…
Just a mod to hold the referenced PTFE coupler. Pretty custom to my setup, but I was asked for the model so posting. If you can use it, great! Feel free to remix!
I have designed a compact enclosure for an AZDelivery (Wemos) ESP32 D1 Mini NodeMCU WiFi microcontroller, including space for an optocoupler module and cable clamp for an RS485 Modbus or S/FTP cable. I use this setup to create a…
Suggested materials PLA, PTEG or ABS I printed using FDM and in PLA, works well to me. Print needs to be done in 45' angle to gain the structural integrity. Suggest 5 layers of wall thickness and 100% infill. Also Organic Supports.
In order for this to work you need to print two on these and you will need 4 m3 screws. I needed to connect 2 picatinny rails because I got tired of carrying my grenade launcher. Have fun.
This is a recreation of a rubber part which connects the adjustable tracking force weight to the end of the tonearm on certain Akai turntable models from the 1980's. The original rubber part is over 40 years old and is often found in a…
10 inch patch panel for Lexman Ethernet Coupler . Material: PETG
To secure the computer to the mount, you need two M4x6mm screws. There are options for 2 couplers, 1 coupler, or no couplers. The model can be accessed on OnShape here .
This piece connects the two stands from the Aixun T3A ( https://s.click.aliexpress.com/e/_c3dRBPjH or https://amzn.to/3QZmkgo ) and T3B ( https://s.click.aliexpress.com/e/_c3ODuVJl or https://amzn.to/4d6iHwA ) soldering stations together…
Coupler designed for an above-ground graywater drainage line. We have a tree and a few other things we like to indirectly water and this makes it possible to use cheaper PVC to make up the majority of the length. Best printed in ASA, but…
The model is quite simple and prints without supports. I have tested it with two different types of couplers and both fit well but your milage may vary. The design can be modified using this OnShape link .
UPDATE April 24, 2026: I have published the third generation of my Coupler Cap for Cereal Container Drybox as Filament-Holding Drybox Cap . The new Gen 3 version grips the filament very firmly , and it has much smoother operation than…
A vertical and horizontal mag coupler for 10 round P-Mags and Hochul Mags. Includes versions for all P-Mags, all Hochul mags, and half/half. WARNING: The coupler will prevent an AR-15 dust cover from fully opening after the mag is…
This is a coupler to link mirrotation device to 12mm button. See : The SolidWorks files are given so you can adapt the coupler design to other telesopes. What do you need : 3 x (brackets + base) 15 x Ruthex M3 inserts 3 x magnets (see…
This is a coupler to link mirrotation device to 12mm button. See : The SolidWorks files are given so you can adapt the coupler design to other telesopes. What do you need : 3 x (brackets + base) 15 x Ruthex M3 inserts 3 x magnets (see…
After printing the parts for my FYSETC ERCFv2 12 colors, I found out that the ERCT coupler blocks are actually meant to be printed from a clear filament (but the FYSETC files mentions it as a opaque printed part) I decided to make it look…
A friend of mine reached out to me the other day and asked if I could make a replacement clip to join snowshoes together as the original clip broke, and Tubbs no longer makes this model or a replacement clip. Found the original cross…
Y filament connector using TPC4-01 connectors (BSP 1/8'' threads). Threads on the 3D printed part are formed upon initial insertion of the TPC4-01 connectors. Recommended print material ASA (But other would work also...). Use 4 wall loops…
You bought an autofocuser. It came with a bunch of couplers to mount it to your focus tube. But you only need one, and now you want to store the others. Store them with gridfinity!
I don't know how this will hold up over the long term, but I thought it was worth trying. As I write this, it is March 26, 2026; I hope to provide an update in a year or so as to how this worked out (or sooner if it breaks!). I have a…
Fits 7/8in or 22mm diameter air chuck quick disconnects. keeps debris out, nice snug fit in TPU
I bought a replacement plate for my GE 731K microwave and it turned out that the protrusions under the plate were higher than in the original. So I had to improvise. The plate that I bought is DE74-00027A and was supposed to be a direct…
Design Concept These couplers are created to connect brio-style trains, enhancing versatility in train play setups. There are two types of couplings. First is classic but with more endurance, second is new type. In that is not necessary…
Completely 3D printed, no additional parts needed, headphone measurement stand using clone E610A coupler and clone KB501X pinna. This design aims for a single ear measurement. For a double ear measurement, use smaller couplers or consider…
This bottle coupler is designed to work with Garnier Fructis pump-top bottles. It prints without supports, but may benefit from a brim. The model as shown was printed in Prusament Galaxy Black with a brim.
A simple slide-on housing that holds a pair of 4-pin or 3-pin (male & female) fan connectors together, like those found on Noctua fan extension cables, but it should work with most fan extension cables that use the standard Molex KK style…
Need to re-spool that messy 2kg spool but don't have another empty 2kg spool? Want to make your own continuous 4kg spool? Perhaps you just want to extend the capabilities of an existing spool-repurposing project. This carefully tuned…
These NEW over-engineered Prusament spools are just so versatile! They normally assemble with bayonet-style twist-lock sides that require a 3D printable tool to open . This over-engineered lid system uses the spool's center hub (plus a…
Russian Description Обзор Запасная приводная муфта для кухонных комбайнов Bosch . Это важная предохранительная деталь, которая защищает двигатель от перегрузки и сгорания при заклинивании ножей. Если ваш комбайн перестал вращать чашу,…
![New Angled Coupler for PTFE Tubing [PC4-M10]](https://media.printables.com/media/prints/37394/images/369595_474b669c-2177-4d92-bb73-0382863ed5f2/img_3225.jpg)
![1-1/2" to 1-1/14" [1.5IN to 1.25IN] Pipe Reducer/Coupler/Adapter (No Supports)](https://media.printables.com/media/prints/467707/images/3833779_84360414-c412-4bb7-8416-d7704ab80c4f/f360.png)
