126 models
Originaly designed for my CTC printer (clone of the ender3 but way too bad product)
Print approx. €0.75–€0.92 excl. taxPreliminary estimate for one variant
Comet Antenna CTC-50M is flat ribbon coax cable for thru window opening connections to an exterior antenna Better Mounting Bracket for Comet Antenna CTC-50M coax thru-wall connector fits onto one end of a threaded 3/4" gray irrigation…
Print approx. €5.76–€7.04 excl. taxPreliminary estimate for PETGSource material: PET
English: Tested and in action Igus Linear Rail Type TWE-04-12 = MGN9C Advantage of the Igus linear guides is that they run lubricant-free and quietly, the model TWE-04-12 is also adjustable and thus the bearing play can be reduced so that…
Yet another Reprap Full Graphic Smart Discount Controller case - this one designed to be mounted on top of my CTC I3 clone printer. Supports are necessary for the case, but only on build plate. Public OnShape document is here:…
I couldn't find any fitting base for skr 1.4 for CR-10 clone that I have. So I changed available ones to fit. I suggest you to plug in all cables before mounting he driver fan and cover. Based on https://www.thingiverse.com/thing:4259233…
After upgrading mit CTC to the E3D-V6 hotend using X-Axis Carriage designs, I found here on Thingiverse, I wanted to be able to see the nozzle with my webcam during printing. Furthermore I wanted to have 2 cooling fans on the side to…
Having a new appreciation for silent 3D printers, I've decided to replace the Anet v1.5 mainboard that came with my CTC A10s with a Creality 32-bit board with silent stepper motor drivers (V4.2.7). My first inclination was to add…
Redesigned extruder block with smaller drive gear hole (11.8 instead of 13 mm) -> longer filament support between the drive gear and hot end so flexible filament does not get stuck in between. As CTC that I own is an Makerbot Replicator 1…
This is a connector piece that holds the wrist rest to the trackball for the Kensington Expert Trackball Mouse. This model appears to work for the wireless version of this mouse as well. I'm sure there are ‘better’ solutions, but this is…
I wasn't really satisfied with the available E3D V6 Mounts for my CTC, so I created my own version. There are 2 Versions available - they are all the same, but different! I would hardyl recommend V003 for single or V007 for dual setup.…
(7 August 2025) v2 - Optimized For 3D Printing Added Print with ABS or PETG Filaments Layer Height 0.2 Walls 4 Infill 30% Grid
Neues Druckbett für den Alu Umbau des CTC 3D Drucker Benötigt wird: Gefräste Aluminium Platte, siehe Zeichnung 2x 12mmx330mm Welle 2x Flaschlager LMEK12LUU - Lange Version 8x M5x40mm Inbusschrauben 8x M4x8mm Inbusschraube 6x M4x20mm…
In many cases, the second extruder in the dual extruder printer isn't used. Each stepper motor added a lot of weight to the print head. This increases ringing/ghosting and other artifacts in prints. It also affects the printers ability to…
The most recent (July 2023) iteration of the couplings used on my models. As close to NEM standards as can be achieved.
I present to you the MMU3 CompactCore, my MMU3 solution that is economical in both space and material for the PRUSA CORE ONE Design requirements : Economical Less than 2 kg of material is required to print all components. No bearings to…
This is a level tool for the dual nozzle Replicator (and clones such as the CTC Bizer). I didn't want to take my entire print head off of it's carriage to level nozzles. Unlike some of the older printers the nozzles on the CTC are held on…
This project started with the hinges I found on this platform. From there it progressed in completely closing my CTC with doors and a lid/top-cover. I planned on adding hinges to the lid as well, but decided to keep it separated from the…
I edited the mount for the cable on the x-axis stepper motor. Befor I couldn't install this fan duct properly: http://www.thingiverse.com/thing:537918 The extruder-carrier (better: the fun duct) 'crashed' into the stepper-motor-housing…
Prusa type radial fan (50mm) holder for MK10 extruder. Doesn't require additional HW (bolts or nuts) Chassis will be fasten with the extruder fan bolt (remove the 10mm nylon pipe). Additional support is given by the edge of aluminum…
After changing a few things on my printer I found that the cooling duct I was using to cool the print was not ideal so I designed my own together with a bracket to hold it onto the MK8 extruder. This bracket also replaces the two nylon…
This is a quick design I made to add two 120 or140 mm fans (one on each side) to my CTC's build chamber. Goal was to make a fan mount, which can be easily removed when you have to access the print bed from the side (i.e. to apply blue…
Ein Spulenhalter, welcher bei dem Alu-Umbau dirket an das Alu-Profil angeschraubt werden kann, wo auch der Y-Motor sitzt. Für Spulen: Durchmesser-Aufnahme<45mm, Breite bis 75mm CTC-Alu-Umbau -> http://www.thingiverse.com/thing:1731902…
Geänderte Y-Motorhalterung für den Aluminiumumbau: http://www.thingiverse.com/thing:1731902 Hiermit steht der Motor nicht mehr über das Gehäuse hinaus. Musste bei den Schrauben, welche zum Tisch zeigen Linsenkopf nehmen, da ich eine…
I recently got an Ender3 Pro and wanted to add to it most of the modifications I've installed on my CTC A10s since I'm happy with how that machine is performing. The A10s is a poorly made knockoff CR-10, so it shares much of the design…
just a simple filament guide. 2x: http://www.thingiverse.com/thing:2173952 3x: http://www.thingiverse.com/thing:2173956 Print Settings Printer: ctc Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0,2 Infill: 20% Notes:…
Last week when I remixed AHoward's “CR-10 belt tensioners” Y axis frame mount, my CTC A10s was not yet restored to an operational state. Motions were perfectly smooth with that model and the tensioner worked fantastically, but once the…
2x filament guide. 3x: http://www.thingiverse.com/thing:2173956 1x: http://www.thingiverse.com/thing:2130148 Print Settings Printer: CTC Bizer Dual Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0,2 Infill: 20% Category: 3D…
We finally upgraded our old first generation Flashforge Creator Pro 3D dual extruder to the quiet control an SKR 1.2 Pro with TMC2209 drivers and a TFT35 E3 to keep tabs on things. I needed to mount the screen after getting everything…
Pivotable webcam mount for CTC Bizer. It should also fit on similar models. "Kabelklemme.STL" is used to clamp the cable on the printer frame. A M3x25 Screw+Nut is needed. Print Settings Printer: CTC Bizer Dual Rafts: No Supports: No…
I built an internal and manual fan controller for up to 5 standard 12V PC-Fans. It should fit many different printers, but I designed it for my Replicator-Clone. The Fan controller I used was the Aerocool F5XT:…
This is an easy to mount and fast to Print Spool holder. I was looking for an easy to install spoolholder that doesn't harm the filament transport and fits any kind of Spools (for example: Small FlexiSmart spools- Picture 4) The result…
This is a modified version of the CR-10 display housing included in xxricsxx's CR-10 Standalone Kit. There are at least three distinct variations of the CTC A10S CR-10 clone. Components differ significantly depending on which variation…
(Does not fit the monoprice architect-based flashforge clone.)
My version of CTC printer enclosure. I used 2 mm acrylic glass plate. On the photo I still use old version of wood hinge. Needed: 2 cylindrical magnet (r=2,5mm h=3mm) 2 screws (10 mm) - my screw head additional 2,5mm but if your will be…
I needed a new tray for my CTC Riverside SLA printer (basically a Form1 Clone.) The price was a bit steep for a bit of acrylic and a piece of tape, so I built one. I've attached several different formats, I designed it in Sketchup, but…
Ctc Prusa i3 e3dv6 mount, mirrored. Fan duct extra can mount fan after printing first parts. Or by using only fan duct mount version 1. Category: 3D Printer Parts
Similar design for ctc i3, but this replaces original wooden front panel Print Settings Printer Brand: Prusa Printer: Prusa Clone Supports: Yes Notes: Can be printed without supports if printed as shown. Needs supports for holes…
KUSBA mount, for use on printers making use of Detlef01's Titan conversion . Mounts to the inserts for the highlighted redundant “endstop” component
This is an adapter to mount an SKR v1.3 motherboard to a CTC Prusa i3 Pro B, replacing the included GT2560 board. Print Settings Printer: CTC Prusa i3 Pro B Rafts: No Supports: No Resolution: 0.32 Infill: 10 Filament: BQ PLA Category: 3D…
The back cover for the 2004 type LCD SDCard reader controller with the vertical connectors and the reset button on the back. The cover will be installed directly on the PCB with the display bolts, leave the nuts out. The cover is a quite…
This is the companion piece to the spool holder: https://www.thingiverse.com/thing:2543519 The mesh with each other using a T-Slot. Designed for a CTC Dual (might fit i3 replicator, Makerbot Dual?) with 5mm laser-cut wood panels. OnShape…
This is a remix of AHoward's Y axis belt tensioner for the CR-10 so it can be used on the CTC A10S. The only change I made to the mounting apparatus portion of the model was to add holes so that two 4mm screws can attach it more solidly…
An easy to mount side window for a CTC Dual. I have cut the parts of 5mm acrylic with a lasercutter, but it should also be doable with a table saw. For fixation I used (for each window) 4 x 10mm M3 screw with one washers (ISO 7093) at…
This is an electronics enclosure for the CTC A10S mainboard. This is for the purpose of eliminating the big hocking black box that sits alongside the printer, and for integrating the printers electronics. I designed this as a temporary…
This is an upgraded version of my "CTC A10S Amazing & Stupidly Overcomplicated Bed Leveling Knob Assembly". I designed the original part hastily out of necessity because the tiny flower shaped make shift knobs that came with my CTC A10S…
Work in progress. But using these now my self. Made longer version. Category: 3D Printer Parts
This is my way to mount e3d Chimera hotend to original CTC (Replicator 1 clone) XY carriage. This design allows you to easy assemble/disassemble hotend in case of any issues or maintenance. From hardware, you will need some M3 screws to…
This is an electronics enclosure for the CTC A10S mainboard. This is for the purpose of eliminating the big hocking black box that sits alongside the printer, and for integrating the printers electronics. Version 1 of this model was…
I remixed a thingiverse V6 designe to fit a V5 Hotend original: https://www.thingiverse.com/thing:2524128/files you can use the original Clamp changes that i made: - Holder hight - thicker Button pusher - thicker Holder - thicker Walls -…
TC03 hotend Mount for makerbot replicator1 and clones. BLtouch is optional. Offset is: X:-30.5mm Y:5.5mm. Z offset for my setup is 2.2mm. Should work with 3dtouch, but you may need add washers. Improtant: Move your X-endstop like in…
Designed from scratch using the layout and coarse dimensions from https://www.thingiverse.com/thing:2460482 OnShape link where you can edit to your custom specifications:…
After gathering some ideas around here, I designed my own spoolholder where the spool rests on 608ZZ bearings. Easy to load and very smooth in supplying filament to the extruder. Design is for spools with total width of around 70 mm. If…
Uploaded under STEP AP242, which is incompatible with Solidworks. EDIT: Use the Revised1 version. That one's more accurate to the actual thing The Mellow NF Zone and CTC heatbreaks for an E3D v6 are 3mm longer than the average heatbreak.…
My CR-10 knock-off printer, listed as a CTC A10S, are sold with various levels of dysfunction, and built from a variety of defective and unbelievably bad parts. I do believe the one I purchased is the worst build quality of any out there.…
Hello, this is precision thumbweel for CTC A10s (CR10 clone) This wheel was inspired by idig3d's CR-10 Precision Thumbdial I tried this model but it would not fit. CTC uses slightly different original dial Oiginal has 18 small protrusions…
A Shorter Version of the CTC Spool holder Category: 3D Printer Parts
Not so much a remix, rather some addition to make it work even better. On my print of the enclosure, the parts didn't snap together really well. Next to that it was just hanging about. I designed a mounting mechanism that clamps the…
When I bought my first 3D printer, I wasn't sure whether or not a new hobby would suit me. I didn't want to spend a ton of money on something I wasn't sure what kind of use I'd get out of, but I wanted something large enough for printing…
Since the built in displays aren't that sturdy, I created a screen protector for the CTC Bizer. Just drive out the display screws and remove the shims. Screw the mounts to the housing and insert the acrylic glass (2 mm). Aaaaand you're…
Hey there, I wanted to upload these to here for anyone who wants to show off their HCTCG gear in their everyday play with a few tokens you can use to have as indicators or as fun when you do any table top gaming!
Plate for mounting an autolevel inductive sensor on a CTC PI3 Pro B . The sensor is an inductive probe SN04-N . You will need to mod the GT2560 motherboard to connect it to the sensor. Put a male pin on the 5v pad, and solder right angle…
As always I wanted to add a PINDA probe, I started by trying to make a drop in adapter but that was not a very good solution due to not having a good spot for the cable. So I mixed this guy up. Print it the same as the org model, fan down…
These shim plates will increase the plywood frame strength as the lips prevent the plywood to split. Place the shim lips towards the bolt and the nut on the even side. The very solid frame you'll get if you glue all parts (but Z rods top…
The CTC i3 2016 comes with the 30mm axle reel holder. Here is the adapter to use for 20mm filament reel in the stand . (The orange nuts are original kit parts). Category: 3D Printer Accessories
Easy ctc replicator e3d v6 mount. Direct drive style. print in abs and use the newest updated file Category: 3D Printers
Displayblende für einen CTC Bizer mit je einem Schalter links und rechts für Beleuchtung und Bauteillüfter. Die Ausschnitte für die Schalter sind 12,8mm x 20,0mm groß. Verwendet wurden diese Schalter:…
3x filament guide. 2x: http://www.thingiverse.com/thing:2173952 1x: http://www.thingiverse.com/thing:2130148 Print Settings Printer: CTC Bizer Dual Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0,2 Infill: 20% Category: 3D…
Hi, Previously I had on my that 'wild boar' looking cooling duct on my CTC. But now I upgraded to E3D hotends, so there was also nee for new cooling duct. Found one close enough and remixed that one. Made some modification on angle…
Work in progress. Linear bearing. My printer missing one, still waiting it from seller. This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/gbSihpfVzxl Category: 3D Printing
Hi, Decided to upgrade CTC 3D with E3D v6 hotends. It was clear that some kind stepper motor bracket are needed for bowden setup, so I designed my own. Hope you like it. On T-part, use M3 theat tap to make threat, open holes with 2,5mm…
Hi, This is remix of "Dual extruder CTC". I just separate base plate for easier printing on ABS an for easier maintaining in case nozzle blockage. This spring works perfect. 2 springs needed.…
Hi, All the fans started to be too loud so decided to upgrade them. I draw air duct to ensure proper air flow over stepper drivers as air flow provided with new fan is lower that original fan had. Nothing special on printing, supports…
I wanted an improved rear in betweener that was able to close the opening of the lid and combat heatloss of the chamber
This is simple spool holder for the CTC i3 Pro B printer. It will probably also fit some of the other i3 clones out there, such as the Geeetech. Just remove the two screws from the top right of the frame, sit the spool holder on top and…
I purchased a select cut kit from amazon for my EGO mower, and found it needed a small spacer to separate the fan from the motor! I designed and printed this spacer to print. Originally out of PLA, it worked until I used an impact to…
I made a remix with a hole center-to-center distance of 45mm. the original was 50mmCTC and it did not fit. Measure yours and print the right one. Printed with PETG 100% infill no supports 0.2mm layer hight 0.4mm nozzle Printed on his side
A holder for two of these standard simple filament sensors that also functions as holder of the cable sleeve. I think i reused some existing holes, but i am not sure. As can be seen in the 2nd picture i later decided to use a fitting to…
My on-hand stock had 4mm push-in fittings with 10mm thread only and parts were already printed and had hole size for M6, So decided to make adapter, which I attached with epoxy glue. Turn fittings into adapter before gluing. Print…
Ich habe meinen CTC Bizer mittels dieses Thing auf einen E3D Extruder umgebaut https://www.thingiverse.com/thing:2348165 Ich wollte meine vorhandenen 40mm Lüfter weiter verwenden, jedoch ist beim CTC wenig Platz nach vorn und mit den…
This is a remix from the experimental remix from this thing: http://www.thingiverse.com/thing:537918 I made less holes than in the remix, so i get more air flow direkt to the nozzle. Category: 3D Printer Parts
This is a mount for the BigTreeTech TFT24 display, designed to work with the BigTreeTech TFT24 display case . It mounts where the old LCD panel would be and covers most of the opening that would've been left. When printing the TFT 24…
This is a small plastic spacer that goes between the mount points. This piece helps keep the hinge tight so that the fan assembly stays in place. Category: 3D Printer Parts
CTC i3 Clone printer parts, including a 1cm testcube. Foto shows Item printed with this clone. CTC Prusa i3 official parts & other contents from SD card by tom666 is licensed under the Creative Commons - Attribution license.
A simple Spoolholder for my modded CTC. Will work on other wooden cases also. No tools needed for changing the spool. Print Settings Printer: CTC Dual Rafts: No Supports: No Resolution: 0.2 Infill: 30% Notes: 3 shells Category: 3D Printer…
This is not much of a major change, but after printing I found the small cable tie holes to be too small. This design replaces the round holes with rectangular cut-outs sized for a 2.5mm wide cable tie. The cut outs at the top of the…
I didn’t print this myself yet, but while installing the original part I came up with a few improvement ideas. Update (11-02-2026): Uploaded Revision 2 added few radious to improve rigidity added .stl version since the step version had…
Most Amateur Radio repeaters now require a low-level audio frequency tone to be transmitted by the user's transceiver in order to 'open' a tone coded squelch. Older transceivers do not have the encoder built in, and in order to use the…
This Thing is featured on the 3D Printing Today Podcast. http://threedprintingtoday.libsyn.com This is a derivative of the Thing uploaded by Coldstone. This thing is meant as an upgrade to the OEM, unsprung feeder parts used in older…
CTC Prusa i3 fan duct mixed 2 version. Just print it, no need support etc. Duct 3 version, points air flow more down away from nozzle. 5_8 version is mix from version 3 and some generic fan part. Using 5_8 version my self now, works ok,…
Made little simpler version. Easy to use. Remix from this. https://pinshape.com/items/32118-3d-printed-hictop-prusa-i3-print-table-leveling-calibration-tool Category: 3D Printer Parts
CTC Prusa i3 power protection. Just put this top of power. Its thight fit, and stays in place by it self. Category: 3D Printer Parts
Power connector cover, edited. Now wires go more easily. Using this in my printer. Print Settings Supports: Yes Category: 3D Printer Parts
Modified version, mirrored and taken some parts out. Perfect fit to CTC Prusa i3. V2 file, more modded. Using that now in my Ctc Prusa. Print Settings Supports: No Resolution: any Category: 3D Printer Parts
CTC Prusa i3 power cable cover. Easy install. work in progress. But im using this now in my CTC Prusa i3. Print Settings Supports: Yes Category: 3D Printer Parts
I made a remix with a hole center-to-center distance of 45mm. the original was 50mmCTC and it did not fit. Measure yours and print the right one. Printed with PETG 100% infill no supports 0.2mm layer hight 0.4mm nozzle Printed on his side
A display box for a CTC i3 Clone I created so I could move the electronics to the outside of my enclosure. I wanted the display vertically mounted since it's just about at eye level for me. This was created in FreeCAD. The file was…
After using the Spring based anti-vibartion feet for a while I wasn't too pleased with the result. To my opinion using the springs the machine is rather instable and shakes all the time especially when the head makes short movements. I…
Bowden clamp reupload from hackaday for CTC i3 Category: 3D Printer Parts
I wanted to add holes for M4 PTFE connectors This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/9R5rVvvozGq Print Settings Printer: CTC 3D Printer Rafts: No Supports: No Resolution: 0.1mm Infill: 100%…
Can be used to mount a Geetech GLTouch/3DTouch to a CTC Prusa i3. Sensor web page : http://www.geeetech.com/geeetech-3dtouch-auto-leveling-sensor-for-3d-printer-p-1010.html Category: 3D Printer Accessories
