Counting matching models…
As seen on X and YouTube: Disclaimer: This is an acoustic model. As such, it does not scale, nor is it compatible with drivers other than the ones specified. Scaling / incorrect driver(s) will result in significantly diminished performance.
Here's a fun design that is super entertaining to play with! This is one of my fidgets in the nested set. Be sure to check out my Three-Legged Nested Fidget and this Little Guy , too! Pro tip: Do not print this with a raft or brim. You…
Ready for MMU. Print the partitions on their side with 0 top and bottom layers. I used honeycomb infill.
GRIDPAC.ONE is the all-in-one printable storage case designed to unify your workspace whether you're deep in the Gridfinity ecosystem or using your own custom inserts. It matches the outer dimensions of Systainer Classic (compatible with…
1:42 Scale German tank destroyer from WW2. There's no moving parts, it's just one solid part. It should print in the orientation I have already sliced it in for maximum strength of the gun barrel. I won't be uploading the Panther tank,…
Grandpa UP Valentine Love Heart Balloons Carl Fredricksen For best results and minimal layer lines, use a fine layer height (around 0.1–0.12 mm) and slower print speeds to capture small details—particularly in the face and hair. PLA or…
I liked my earlier design, but found it tricky to extract individual discs sometimes. This design removes that issue as it uses removable “drawers”. The drawers are held in place with 10Øx3mm magnets though these aren't entirely…
I printed with 40% infill ABS for better structural rigidity and heat resistance.
I liked the idea of this design …but I wanted one with wider and more more slots and would not require supports to print. So, I created this design which has 8 slots to fit standard 5-inch/127mm sanding discs. I made the walls have…
This model comprises three parts, easy to print without supports. Assembly requires an M3 screw and nut. Assembly instructions: 1. Print the parts (suggested: lower layer height for smaller pieces) 2. Insert the nut into the hole and the…
Let me help alleviate your stress. Did you know that stress is the leading cause of “early onset old-person death”?! It's true! You and I can remedy the situation with this easy-to-make print! I love this simple print; I've used 0% infill…
I designed this to hold 5 different grits of sandpaper for my 5" random orbital sander. Each one is labelled for easy identification. I can customize it if you have different grits, just let me know. Also has two holes in the rear for…
Printed with PLA. There is a thicker Version with 2mm Wall thickness. The original has 1,5mm Wall thickness with prints much faster.
a320 Overheadpanel (Not completed).
A Gridfinity System 3x3 bin for tightly holding 25 Army Painter paint bottles (or other bottles with 24mm diameter). Designed to store the Army Painter Speedpaint mega set.
Here are 5 different printable versions of dpads for the Miyoo Mini v2. Dimensions are taken directly off the console and fitment should be close to stock. The Different versions are: Regular concave version with arrows (like stock)…
Sanding paper holder for eccentric grinder 125mm Mounting is by means of two screw holes. Print Settings Rafts: No Supports: No Infill: 20% Filament: PLA or whatever…
125mm & 150 mm sandpaper holder with floating dividers for easier organisation in the workshop. The Cradle is not my design I have remixed it a bit for my needs. I added the dividers since the use for me depens on the type of job I do. So…
First of all credits goes to the original design: https://github.com/Midnite3DP/voron-bedpan I slightly changed a lot from this design to have a smooth Bedpan design with cover for my Voron 2.4 (no matter which bed size. Originally I used…
The screw is now reverse thread, so counter clockwise screws it in. you will need to glue the clip to the body, i use epoxy. I added an extended clip, this pushes the dispenser out away from you, - i found that my clothing was getting in…
***If you like what you see please give a “Like” and a “Follow”! The goal is to get over 200 followers!*** This is the first in a series of sandpaper holders. This is the medium size that is designed to hold a piece of sandpaper that is…
This is a tape dispenser for tape with patches for IPSC targets. It can hold a tape 23mm with 1000 patches 20 mm in diameter. The hook must be glued on the back. The screw can be unscrewed with coin €1, €2 or 50 cents. It has an opening…
Box s úchytom na odpad filamentu pre 3D tlačiareň FLASHFORGE AD5X
Calling this done. I guess if you make a rolling model you have to motorize it and add an UNO to control it. So I took the Panther chassis I did and modified it to hold an UNO, a motor controller and some 12v motors. Then modified the…
A 3x3x3 stackable gridfinity tray designed to store 125mm/5" sanding pads, with a notch to make easy grabbing it with your finger. With 3 units tall it holds between 10 and 20 sanding pads depending on the grit (the coarser the grid, the…
Self tensioning and clamping in one, no Winkles, always smooth For short stick, cut the sandpaper to a length of 230 mm and a width of 12 mm For long stick cut the sandpaper to a length of 280 mm and a width of 12 mm Also goes as a nail…
Gridfinity size 3x3 is 126mm so had to remove the walls to make it fit and not waste space. Update 221005 Minor tweak to measurments Added proper size files
Hobby tools: sandpaper holder (different sizes), seam sander
Update 29 jul 2022: Made the hole in the stone holder bigger so that the stick attaches easier. Prerequisites: To 10 mm M5 screws with two hex nuts Print with 2 mm walls/top/bottom for stability and with no support. 150_5_20.3mf: For…
Solid D-pads, due to their geometry, incorrectly register diagonal inputs if a cardinal direction is pressed too hard. Split D-pads solve this by having a separate pieces for each directional button, which eliminates cross-button…
Very practical sandpaper holder. If the sandpaper is used up, the sanding belt can simply be moved a few centimeters. The sandpaper belt holder consists of 3 printed components: Block Tensioner Eccentric Other accessories: Cylindrical pin…
V2 | Remodeled This tray has been made for more efficiency during sanding. This tray is for sanders with a ⌀ of 125mm with 8 hols. If you've suggestions or feedback, please let me know or comment below.
5 inch Round Sandpaper Holder. I upload the following grits: 40, 60, 80, 100, 120, 150, 180, 220, 240, 320, 400, 500, 600, 800, 1K, 1200, 1500, 2K, 5K and blank. If you need other grits let me know and I'll upload them. 2021-02-16 -…
Gridfinity holder for sandpaper for an orbital sander (⌀: 125mm)
Instructions from creator: 0.3mm layers 3 shells 4 top and bottom solid 40% triangle infill I used 0.2mm layers
I wanted a way to store my 5 inch orbital sandpaper discs but all the designs I kept finding use too much filament. Some are good but this one is even simpler. A 5 opening holder will use about 150gram of filament which is a fraction of a…
This is one of my fidgets in the nested set; check out Grandpa's Greatest Nested Star Fidget . Here's a very fun fidget for relieving stress, and it's not too noisy while playing! The standard version (black & blue) has five rings while…
As seen on YouTube: Disclaimer: This is an acoustic model. As such, it does not scale, nor is it compatible with drivers other than the ones specified. Scaling / incorrect driver(s) will result in significantly diminished performance.
5 inches sandpaper drawer storage. 12 drawer version and 6 drawer version available. It can be wall-mounted. This is my first design. I was looking for something like this but found nothing, so I designed one. Hope you like it. I made the…
UPDATE: Make sure to use "5 inch sandpaper storage box 8 FIXED.stl" and not "5 inch sandpaper storage box 8 drawer less material.stl". I corrected the height of the one drawer that was 1mm too small. Or use the original box (with less…
I designed this sandpaper caddy to be wall mounted with screws by default. If you have a Wall Control system, then I've also included an adapter pin that makes it compatible with that as well. The label slug can be customized with text in…
Add a pause at 8mm and push in a 1/4-20 nut. Make sure it is recessed below the current print hight. I printed mine with prusament PC-CF, .2mm, 5 walls to make the outer wall solid. The lock bolt that comes with the mount will thread…
🟨 Material: Prusament Mango Yellow PETG it looks like a 🐝 DeWALT yellow ⬛️ Layer: 0.3 is enough
This birdhouse is a special gift for my Mom, inspired by the one my late Grandfather made, which has since decayed. She cherished his birdhouse, so I wanted to create a durable version that she can enjoy for many years to come. Before you…
Sandpaper holders for festool 150mm sandpaper disks. Designed to be more easily lifted vertically, and for holders to be labelled from the top, making them identifiable by looking straight down.
Ich habe hier einen Schleifpapierhalter für meine Baustelle konstruiert. Die obere Klemmplatte besitzt Noppen, welche sich durch das Schleifpapier bohren, welche den halt nochmals verbessern. Die Schrauben habe ich als Rändelschrauben…
I've designed two separate hexagonal wall panels that you can use to enhance your living area, gaming room, children's room, office, or 3D printer background for videos. The special thing about them is that you have the freedom and option…
Simple, and keeps the filament tightly wound. Sliced with 15% infill on my Prusa Mini, it uses .28m of filament, .83g, and takes 8m. I love this filament clip, and this is an upgraded version - the outer clip has a potential for breaking…
This tray neatly stores and organizes 80mm triangluar sanding pads used by typical oscillating tools. Can be printed horizontally or vertically with decent bridging.
BEFORE STARTING THE IMPLEMENTATION OF THE PROJECT, READ CAREFULLY THE ENTIRE DESCRIPTION AND VIEW THE PHOTO GALLERY !!! Hello Everyone I designed “Bambu Lab A1 Mini - Rotary Spool Holder Adpater” for the original product Bambu Lab Rotary…
A 4x4 gridfinity bin for holding 150mm sandpaper. My bin holds 5 grits of sandpaper, with trays with tabs to lift up the stack to reach the desired grit. A separate lid on top holds a smaller stash of sandpaper that is currently in use.…
I bought a multi-pack of sandpaper and I wanted a good way to store it that allowed me to easily access the sandpaper I wanted. So I came up with this layered offset design, and it's worked well for me. The separate layers make it easy to…
Simple wall holder for 125mm pads. Each section accomodate around 50-100 sheets. Print Settings Printer: vking Rafts: No Supports: No Resolution: 0.25 Infill: 10% Category: DIY
Update: Uploaded a new model of the 2.25 sander as well as new 1.125 sander. New models facilitate easier printing. A sanding block that perfectly fits a 1/8 sheet of 9x11in sand paper. Tear the sand paper sheet in half the short ways.…
Two M3 x 25 screws and nuts for the hinge. Four 5mm x 3mm magnets glued in place to keep it closed. It should print well without supports. I have added the Fusion 360 file for those that may want to tinker with the design. I'm not much of…
If you have a Milwaukee M12 FUEL Orbital Detail sander 2531-20, and wanted a good place to store your sandpaper, this it. I printed this with PETG on my Prusa Mini, and put it right next to my sander. Looks decent enough, and holds plenty…
If you have used the original Snes controllers you immediately notice that the 8bitdo dpad is much looser, which at first seems to be nice but it might not perform as well as the original. This is not a big issue in all games but for…
Default print settings should work just fine for this. I used gold silk pla and black pla for mine.
I really like this mount the only problem is this adapter. I'm on my second full mount because this same piece breaks due to sun damage. The four threaded sides on the “bolt” portion of the adapter fail. Hopefully this saves you $20 like…
I love the simple way these fidgets work. I added a chamfer to the inside edges for a comfortable feel. You can mix and match the colors, textures, and even “hot swap” filaments during printing for even crazier combinations! The…
This is a template I made and printed to make cutting strips of sandpaper easier for these sanding sticks https://www.prusaprinters.org/prints/22236-customized-sanding-sticks-with-labels Height is 3mm but you can adjust the Z up or down…
Updates: (8/30/23): Added open/closed double-wings versions, which some people had requested because they found the clip tilted in unevenly wound spools. Also added a mostly cleaned up Fusion360 and STEP files for these variants (in case…
A blank, matte-white model inspired by the warmth and wisdom of a classic grandpa figure. This DIY collectible invites you to add your own loving details—perfect for heartfelt painting and honoring the gentle strength of elder generations.
I created a sanding block for the 50mm wide sanding paper I have. You'll need a M6 hex nut + a 15mm-ish M6 bolt.
Clarinet/Flute Microphone Clip for DPA 4099 or T.bone Ovid CC100 from Thomann. Uses double-sided velcro for mounting.
Summary This sandpaper tower is ideal for keeping you sandpaper organized and most importantly, free from dust! Ideal when you don't care about wood dust management ;) There is a collection you can download from or you can download the…
I was not willing to spend money on a sanding block, so I designed this two-piece construction. For my purposes, it works great. For clamping you need 2 x M5 screws and also 2x M5 wing nuts. Print Settings Printer: Artillery Genius Rafts:…
I wanted a tiny sanding block to keep in my tool belt for carpentry work. This is not designed for lots of sanding work, simply to quickly tidy up a cut edge on a cladding sheet or similar application prior to installation. For instance,…
Pen holder for Army Painter Speedpaint Markers. Holds 37 markers
I created this sandpaper holder for my Gridfinity system. It needs 4x3 modules and has 10 slots each having a width of 12,4mm. Each slot can store roughly 10 pieces of sandpaper (e.g. Bosch C470). I guess it is also perfectly fine storing…
Designed to fit Porter Cable and Black and Decker Type 340/341 series sanders. Confirmed fit for: Dewalt DW411 Type 2. COULD ALSO POSSIBLY BE COMPATIBLE WITH: DeWalt: DW411 Type 1 Palm Sander DW411 Type 3 Palm Sander DW412 Type 2 Orbital…
Print the cello and double bass adapter with TPU with 100% infill. I used Filaflex 82A For the pencil mic adapters both PLA and PETG work. No supports, only the 170 version doesn't print very nice but is still okay. For the cello, my…
OVERVIEW This project is a 1.5-inch IDPA-focused competition gun belt designed to be manufactured on a consumer FDM 3D printer and assembled using inexpensive off-the-shelf hardware. The goal was to create a lightweight, modular,…
Intention to print these 4 parts and then use ½inch nominal (0.472 in) plywood for top and bottom. To use threaded rod (¼-20 or similar, those are 6.5mm holes) to clamp shut I'm finding 400-800g per part, so this is a plastic hog… I'm…
Another variation of t.bone ovid/DPA microphone Intended for the left/bass side of accordion to attach the microphone to the accordion belt. Intended to use with this ebay cable organizer .
Inspired by DisKeeper, but designed from the ground up to be a bit a bit taller and have a more robust french cleat. 125mm (5") and a 150mm (6") holders. Designed to use 2x (each) M2x12mm self-tapping hex screws to connect the cleats to…
Try this as a smoother, less broken-up version: 20 cm x 20 cm Print Bed Version This is a modified version of the subwoofer enclosure, split into smaller parts so it can be printed on 20 cm x 20 cm print beds. I added connectors to make…
Sandpaper holder or template. For fixing sandpaper for better handling during grinding. The sandpaper is pushed in and fixed with an inner wedge. The subject consists of two parts in the photo.
Leviga meglio e con meno sforzo grazie al SandPaper Holder , il supporto pratico per fissare la carta abrasiva. Il design ergonomico garantisce una presa salda e confortevole, mentre il sistema di bloccaggio mantiene la carta ben tesa e…
parts 1,2,3 need to be glue together / nutno slepit dohromady parts 4,5,6 need to be glue together / nutno slepit dohromady For 1,2,3 -recommended material/ doporučený materiál - PETG
Update Notes 29 August 2025 : Added new version of the Guard ring (v4). a little bit hollow, with added wings inside to add more resistance to the left and right direction button Added new version of the Dpad insert (v4). Longer part for…
Oscillating Triangle Sandpaper Holder: This is a remix of a design I found on Thingiverse. However, I completely redrew it and added the following: Increased wall thickness/rigidity from 1mm to 3mm Made stackable with posts on lid and…
Fixed and remixed original model to remove the Gridfinity connectors on the bottom and adjust the dimensions to comfortably fit my 5.5" x 4.5" (~140mm x ~114mm) sandpaper in 10 different grits. Tray is 80mm high, 140mm long, and 130mm…
Holds about 10 regular disks per grit easily. I store it on its back for accessibility, which can cause the sandpaper to to catch on its neighboring grit. As a result I store my sandpaper alternating per grit( hook to hook and loop to…
French Cleat Sandpaper Storage for 5inch random orbit sanders with dividers and positioner for quickly mounting sandpaper onto the sander base. F3D file is included and fully parametric. 3/4inch french cleat attaches to the main body with…
Storage for 150cm sanding disks. Sorted by grit size. Print the sizes required, plus a top and bottom. They will click fit together, I added a blob of CA to ensure they didn't seperate. Attach to wall, or stand on shelf.
Miniaturized target for dry fire practice at home. Target mounts into a single or dual bracket configuration. I put the brackets in a cheap telescoping tripod / selfie stick from Amazon - makes adjusting height super easy. Target is blank…
If you are not using the spool holders, the adapter allows the attachment of a Honeycomb Storage Wall (HSW) to the side for extra storage. Included is a hexagonal HSW grid that works well in the space. Of course, you can print out your…
IDPA box. You can check the check to make sure your gun fits your division. IDPA BOX - is for SSP, ESP, SPD - 8 ¾” x 6”
a realistic Handpainted duck creation Have fun
simple fan adapter 40 --> 80 mm Category: Electronics
Little Helper to fixate the sanding paper on a BOSCH GEX150/125. Will also work with other models of BOSCH 150mm orbital sander Print instructions Unassociated tags: GEX150/125 Category: Machine Tools Print Settings Resolution: 0,2…
M6 Hex Cage Nut Holder/Adpater Fits a M6 hex nut to use as a cage bolt, other models didn't suit my rails for some reason (these rails https://surplustronics.co.nz/products/10899-rack-strip-single-angle-16u-black) so I made my own…
Trash can (Mülleimer, odpadkový koš) for VolksWagen / VW / Sharan / Seat Alhambra
A tray to hold 80mm triangle sandpaper for oscillating tools. This version is remixed to 100mm in length for smaller collections. Included the divider tags for convivence though they have not been altered from original.
Mini sanding block for sandpaper. It is always useful when you need to sand the material gently and precisely. Junk paper? Replace it or print more blocks and have different grains on hand.
I printed this in PETG as that was all I had. PLA should be fine as well. It is a long 17 hour print.
I reworked the model benoitmeunier so that it would fit the project Honeycomb storage wall and to accommodate 90mm sheets of paper. I have attached a blank label to add gradation and a set of labels for multicolor printing without MMU. To…
I purchased sandpaper in sheets of 9 x 3.6 inches and soon discovered I didn't have a suitable box to store and keep them organized. So, I threw this together. I decided to add labels identifying the grit instead of printing the numbers…
