P
PrintablesEric Cardinal
Drywall Anchor
Drywall anchor, easy to print
Print approx. €0.49–€0.60 excl. taxPreliminary estimate for one variant
- Downloads
- 5,148
- Likes
- 878
- Rating
- 4.9
Search results: drywal
Counting matching models…
P
PrintablesTennessee Mats
Threaded Drywall Anchor
Anchor that screws into drywall, with internal thread for 8-32 bolt. Simply drill a ¼" hole in your drywall and turn the anchor in with a Phillip's screwdriver until the end is flush with the drywall. The threads in the center hole accept…
Print approx. €0.27–€0.33 excl. taxPreliminary estimate for PETGSource material: PET
- Downloads
- 3,081
- Likes
- 733
- Rating
- 4.78
P
PrintablesHappyAtom
Electrical Bracket for Drywall | Old Work Low-Voltage Box | 1-Gang
If you find this file valuable a $1 Venmo donation would be awesome! Thank you! Designed to work with two 1.5-inch drywall or wood screws. Run the screws in and out of the clips a few times to reduce friction. Don't overtighten or use a…
Print approx. €1.54–€1.88 excl. taxPreliminary estimate for PETGSource material: PET
- Downloads
- 1,566
- Likes
- 247
- Rating
- 4.89
P
Printablesishikawats
Drywall Stud Finder
This is a simple drywall stud finder. It uses a strong neodymium magnet to detect drywall screws which indicates possible stud locations. Move the stud finder across the wall until the center indicator starts to rattle and snaps in place,…
Print approx. €0.25–€0.30 excl. taxPreliminary estimate for one variant
- Downloads
- 478
- Likes
- 216
- Rating
- 5
P
PrintablesTom Anderson (The Real NEO)
Drywall cutout Templates for outlets/switches
2 gang box is 4.5x4.5 cutout so conduit box can mount low current box cutout for single gang snap-in box
Print approx. €0.62–€0.76 excl. taxPreliminary estimate for PETGSource material: PET
- Downloads
- 267
- Likes
- 13
- Rating
- 5
P
PrintablesAsa
Drywall Grommet 2.5inch outer diameter passthrough
I use this grommet in an unfinished basement with partial drywall walls. Use this if you have access on both sides of a drywall wall Includes fusion360 files as well as STEP I printed with default ASA settings on a Prusa XL. PLA should be…
Print approx. €0.41–€0.51 excl. taxPreliminary estimate for one variant
- Downloads
- 20
- Likes
- 4
- Rating
- 0
P
PrintablesJM3D
BETTER DRYWALL ANCHOR
MY NEW DRYWALL ANCHOR INSPIRED BY https://paulbhardware.com/snapskru-drywall-anchor-8x1-1-2-snap30011 I ADDED A BIT TIP TO IT AND IT IS ALSO DESIGNED TO HAVE A WIDER OUTER RING TO MAKE FOR A TIGHTER FIT TO THE WALL. PRINT WITH PETG AND AT…
- Downloads
- 2,618
- Likes
- 1,115
- Rating
- 4.6
P
Printablesremotelove
Printable Drywall Mount
A multipart drywall mount that can be oriented to print for optimal strength. I have printed at layer heights of 0.2mm and 0.35mm and both work fine. (It is a tight fit for the parts but that is exactly what we need for its application)…
- Downloads
- 2,102
- Likes
- 2,133
- Rating
- 4.89
P
PrintablesSherlock_Ohms
#6 Screw Drywall Anchor with Threads
Expands as screw is inserted to keep it snug in the drywall. No supports needed. Recommend printing at <0.20mm layer height.
- Downloads
- 1,896
- Likes
- 204
- Rating
- 5
P
PrintablesLoboCNC
Drywall Nubs
Drywall nubs? These auger-style drywall/plasterboard anchors have a little knob on the end that you can either hang skinny things on directly (like lanyards, picture frame wire), or you can use them as anchor points for accessories with…
- Downloads
- 1,395
- Likes
- 667
- Rating
- 4.89
P
Printables3DMegoldasok
Rigips, plasterboard/drywall dowel
Rigips/plasterboard dowels, 2 variants, with PZ2 or PH2/PD2 bit. Must pre-drill with Ø6 or Ø6.5mm drill! Printing from PETG or Nylon or strong, extra PLA variant. Filament layer adhesion must be very good! (I printed out from Fiberlogy…
- Downloads
- 1,388
- Likes
- 227
- Rating
- 4.95
P
PrintablesPtarmigan
Drywall Anchor
There are many types of commercially available drywall anchor. However, most of those designs don't perform well when 3d printed. So rather than recreating a design optimized for injection molding and adapting it to 3d printing I decided…
- Downloads
- 1,334
- Likes
- 323
- Rating
- 4.9
P
PrintablesJustin
Drywall Cable Grommet with Cap (Parametric)
In my experience cable grommets are expensive, hard to find, and never quite the right size, shape, or color for my needs. That means they're a nearly perfect use-case for 3D printing, because you can print the exact number, size, and…
- Downloads
- 1,272
- Likes
- 303
- Rating
- 5
P
PrintablesJohn Wayne
drywall 45 degree cutter, strug do płyt gk 45 stopni
Device for 45-degree chamfering of plasterboards in drywall. Small and convenient to useAll trapezoidal blades up to 62mm fit. Chamfer width +- 6mm. The nut works easily after the first screwing in. In the slicer, the model must be…
- Downloads
- 1,105
- Likes
- 182
- Rating
- 5
P
PrintablesMcAbra
Drywall CD60 profile mount aid (uchwyt do karton-gipsów)
Why? My buddy showed me those when we were talking about a drywall ceiling I was about to put up in my living room. While many different tools like that exist already I wanted to make my own to practice CAD and add mounting for the “laser…
- Downloads
- 961
- Likes
- 149
- Rating
- 5
P
PrintablesUGhpbAo=
Drywall Anchor
Description The “Stubbie” design by LD.P worked really well, but in common with the commercial plastic anchors I was getting breakages and No. 8 screws tended to strip out the anchor. So I set myself the following design goals: Should be…
- Downloads
- 795
- Likes
- 112
- Rating
- 5
P
PrintablesLevi
Drywall Split Anchor
Drywall anchor to hang light objects on drywall without a 2x4 stud. Size your screw so that it digs into the top hole, and will split the anchor as it is screwed in. Drill ¼" hole for the anchor, use #6 size screw 0.2mm layer height with…
- Downloads
- 620
- Likes
- 72
- Rating
- 5
P
Printablescrimcron
Hand Sander / 150mm Disc Sander / Drywall Sander including vaccum adapter
General Information: A hand sanding tool for 150mm sanding discs and sanding grids with an optional vacuum adapter for dust extraction e.g. for woodworking or drywall works. Usable for 150mm sanding discs or grids I used 20mm…
- Downloads
- 582
- Likes
- 100
- Rating
- 4.6
P
PrintablesJM3D
BEST DRYWALL ANCHOR
MY BEST DRYWALL ANCHOR YET IS DESIGNED TO USE A PHILLIPS HEAD SCREWDRIVER TO INSTALL ALSO HAS A BIT TIP ON IT THAT SNAPS OFF EASY FOR DIFFERENT LENGTH SCREWS TO BE INSERTED AND IS DESIGNED TO HAVE A WIDER OUTER RING TO MAKE FOR A TIGHTER…
- Downloads
- 415
- Likes
- 43
- Rating
- 5
P
PrintablesLD.P
"The Stubbie" Drywall Anchor
I designed this peculiar drywall anchor iteratively, following the demise of coat hanger screwed in drywall with "standard expansion-type drywall anchors" (the narrow split ones). I started by reproducing the "threaded" type of drywall…
- Downloads
- 387
- Likes
- 61
- Rating
- 4.71
P
PrintablesHi_Im_Dave
Drywall Outlet Marker/Box Locator
Simply place in outlet box and put your drywall over the top. Marker will push through the sheet-rock. Then Router or cut out your box. You will need supports for the tip. Recommend printing in ASA or better. This is V1 Leave feedback for…
- Downloads
- 338
- Likes
- 37
- Rating
- 5
P
PrintablesSubSite
Network Cable Drywall Passthrough
Instructions: Drill a 20 mm hole through the wall Choose the "long" part according to the thickness of your wall Insert the "short" part on one side, and the long part on the other Fasten with a 3 mm wood screw that's long enough to reach…
- Downloads
- 264
- Likes
- 131
- Rating
- 5
P
PrintablesKlamanDesign
Drywall Patch
This is a simple drywall patch that allows you to quickly patch large holes in drywall without needing to purchase patches. The patch is 7x6" (177x152mm) but can be sliced to fit. Simply attach to the wall with a thin layer of mud and let…
- Downloads
- 262
- Likes
- 43
- Rating
- 0
P
Printablesfns720
Drywall ceiling lamp cone
One of our client asked us to install a lamp on the suspended drywall ceiling which is normaly used on concrete ceilings. As it was impossible to mount a hanger hook on the real ceiling and the original lamp's covering cone did not stay…
- Downloads
- 256
- Likes
- 103
- Rating
- 5
P
Printablescreeg2
Drywall Sanding Vacuum Adapter
These are adapters to hold a drywall sanding sponge while attached to a vacuum hose to minimize dust during sanding. Channels around the sponge allow airflow from the sanding surface to the attached hose. Sponge is held in with a friction…
- Downloads
- 250
- Likes
- 44
- Rating
- 5
P
PrintablesNoneYaBidness
Drywall / OSB Carrier
This is a tool that helps you carry OSB or Drywall.
- Downloads
- 229
- Likes
- 49
- Rating
- 0
P
PrintablesKodagraphy
Parametric Drywall Anchors for Machine Screws and Bolts
A collection of 20mm long drywall anchors for metric machine screws, with a FreeCAD (0.20.2) FCStd file to customize the nominal diameter, length, thread pitch, and more. Tested with M6 and M12 bolts as shown. Make sure to do a test print…
- Downloads
- 216
- Likes
- 47
- Rating
- 0
P
PrintablesJoe3020
5in Drywall Sanding Block
Experimental work in progress, please provide feedback. Sized for 5in sanding disks common in home improvement stores. 1.25in ID vacuum attachment
- Downloads
- 210
- Likes
- 47
- Rating
- 5
P
PrintablesMarcElbichon
Drywall 2in Cable Grommet
Simple drywall grommets for cable management, there are a closed, open and 2 cables (8mm) version. It fit in a 2in hole. Designed for 1/2 drywall Enjoy!
- Downloads
- 207
- Likes
- 51
- Rating
- 5
P
PrintablesJefficus
Flip Anchor for Drywall (OpenSCAD)
I've seen a variety of methods for printing reinforced drywall anchors, but haven't found one that printed reliably on my printer and did the job. So I've borrowed some ideas from those other places and created my own version in OpenSCAD.…
- Downloads
- 206
- Likes
- 37
- Rating
- 0
P
PrintablesMisterMaker
Drywall bit
It fits on a 10mm bit holder, I have not tested the length. But you can easily scale the height up to adjust the length. The fit was tight for me but that is good so no clue needed, also can use the drill to push it in while rotating.…
- Downloads
- 201
- Likes
- 50
- Rating
- 5
P
PrintablesRuShan
Access Panel for drywall
Adapted the model from boksbox on cults3d so it was just two pieces and fit the drywall (½") in my basement walls without needing the extra inside frame. The clips instead of being glued on are now part of the print which only requires…
- Downloads
- 174
- Likes
- 30
- Rating
- 0
P
PrintablesShiba_Vindicator
Level drywall repair with break away screws
Need a clean way to repair drywall without screws or mesh? Need it to be perfectly level for minimal joint compound/mud? Too many times I find that drywall fixes make uneven surfaces, so this is the fix you need. Please note it is a…
- Downloads
- 170
- Likes
- 72
- Rating
- 5
P
PrintablesShron924
Drywall Grommet for speaker wire
Cleaning up my media cables I needed a grommet to fill up the hole I created for wire fishing. This was a grommet I made to fill the ½ In hole I was passing the speaker wire through. Fits in ½ In hole Inner Hole diameter ¼ In Quick and…
- Downloads
- 169
- Likes
- 33
- Rating
- 0
P
PrintablesNot much here
HSW connectors for Ramset Wallmates Plasterboard/Drywall screws
Fittings to attach Honeycomb Storage Panels to plasterboard or drywall interior walls, using Ramset Wallmates WM25 plasterboard anchors. The anchors are sufficient to hold the panels, no extra screws are needed. Hollow cover to stash very…
- Downloads
- 166
- Likes
- 24
- Rating
- 0
P
Printablesecarlson88
Drywall Saw Sheath
1/6/20 Added additional file with tighter internal tolerances + lanyard hole Tool bag and myself kept getting cut up by my Irwin Drywall Saw. Made this simple sheath to solve the problem. Print standing upright with brim Print…
- Downloads
- 165
- Likes
- 24
- Rating
- 5
P
PrintablesChris
Parametric Access Hatch – Customizable Ceiling & Drywall Cover
I designed this parametric access hatch specifically to be inserted into drywall (plasterboard) panels , particularly for ceiling installations . It provides a clean and practical solution for creating an inspection opening , allowing…
- Downloads
- 163
- Likes
- 28
- Rating
- 5
P
PrintablesHDRoni
osVac and Festool adapters for C35 Bosch GTR 55-225 Drywall Orbital Sander
Festool D27 DM-AS/CT and osVac Neo M32/M40 adapters to Bosch C35. I modeled the adapter myself and tested it until it fits perfectly! Because of the grip surface you can easily remove the adapter. OsVac M40 and Festool D27 combi-adapter…
- Downloads
- 161
- Likes
- 22
- Rating
- 5
P
PrintablesCJ Printing
Drywall Hawk
These settings are what I used. You might find different settings work better for yourself but I put these here for a base. Layer height: 0.2 mm Material: Prusament PC Blend Carbon Fibre Infill: 25% I added fuzzy skin to the handle.
- Downloads
- 154
- Likes
- 27
- Rating
- 5
P
PrintablesDaniel Ryan
Drywall Dust Catcher
A simple model to catch drywall dust when drilling into drywall. Hold the tool against the wall with the hole you want to drill centered in the hole on plate of the tool. Drill your holes while holding the tool against the wall to catch…
- Downloads
- 154
- Likes
- 9
- Rating
- 0
P
Printablesjackharvest
Nintendo Switch Lite Wall Mount Dock (Drywall Screw Remix)
The original is awesome -- I just didn't mind putting holes into the drywall with drywall screws (my kids are young and like to be rude to some of this wall mounted stuff). This remix is the same, but, adds countersunk holes for your…
- Downloads
- 150
- Likes
- 19
- Rating
- 0
P
PrintablesHappyAtom
3X! Gang Low-Voltage Electrical Bracket for Drywall | Old Work Box
3-Gang Electrical Bracket for Drywall - @claylinco generously made some variants and mods to the single gang file. There are now 2, 3 & 4 gang brackets! “I've modified it to have center markers and holes to mark the cut line on the wall.”…
- Downloads
- 145
- Likes
- 32
- Rating
- 5
P
PrintablesFusilier
Drywall Compound Scoop
Prints flat with no supports needed
- Downloads
- 142
- Likes
- 29
- Rating
- 5
P
Printables3dprints4life
Shelf Bracket Drywall Construction / Konsole - Regalhalter Trockenbauwand 17cm x 17cm
EN: The bracket is suitable for mounting 20 cm wide shelves on drywalls. M5 dowels can be used as cavity dowels. The hole can be subsequently extended for larger M6 dowels. If you like my model(s) please leave me a like to support my…
- Downloads
- 140
- Likes
- 18
- Rating
- 5
P
PrintablesCattus Printus
Gypsum plasterboard/drywall holder support tool
This is a simple tool that helps with drywall ceilings especially when you work alone. You screw in fist plasterboard then slide holder onto one of the screws and then when mounting second plasterboard instead of having to hold it all by…
- Downloads
- 137
- Likes
- 24
- Rating
- 0
P
PrintablesDGA
Drywall cutting tool
Drywall cutting tool for Stanley 0-11-911 blades, mounted on 20x20mm square aluminium tubing with pencil mounting. Pencil mount should be glued to the base of cutting tool. M10 nuts- 2 pieces M10 x30mm or longer bolts -2 pieces M6 nuts- 3…
- Downloads
- 126
- Likes
- 46
- Rating
- 0
P
PrintablesOSSY House
Drywall Sanding Sponge Vacuum Housing
Drywall vacuum attachment for sponge 4.9" x 2.9" X 1" Print it with PLA+ Standard settings, nothing special. No support is needed. Just glue the cover part. Design inspiration thanks to: Drywall sponge sander vacuum attachment by j5coat -…
- Downloads
- 126
- Likes
- 25
- Rating
- 0
P
PrintablesZemoj
Drywall Passthrough
I designed this to pass through a standard residential wall. Can be used for an air vent or passing cables. The flanges are 5", and the tube is designed to fit through a 4" diameter hole in the wall.
- Downloads
- 125
- Likes
- 33
- Rating
- 0
P
Printablesbwschulz
Vacuum drywall sander
I have a bunch of dings, cracks, and popped nails on the ceiling I've repaired, but when it became time to sand them the dust was so much worse than the walls. The dust goes everywhere and protecting the (much larger) area from the dust…
- Downloads
- 125
- Likes
- 30
- Rating
- 4
P
PrintablesSerhii Muravskyi
conductor for drywall
печать из материала ABS или PETG @сопло 0,4 мм you will need 2 bolts and 2 nuts, which are best soldered
- Downloads
- 119
- Likes
- 18
- Rating
- 0
P
Printablesfns720
DIN ring mount for 65 mm diameter / 50 mm deep drywall electrical device box
I have an IKEA SAMLA board hanging on my study's wall for KNX hardware test. The board has DIN rails which is a perfect mounting solution for most of the devices - except the pushbuttons which require a round electrical device box. I did…
- Downloads
- 119
- Likes
- 37
- Rating
- 5
P
PrintablesGlowKitty
16mm rod towel rack brackets 3d printed drywall anchors
5 walls and 30% infill in PLA were my print settings 92mm spacing vertically between the two drywall anchors Use some short m3 screws as setscrews for the poles
- Downloads
- 117
- Likes
- 31
- Rating
- 5
P
PrintablesJoris
Drywall screw knob
This is an drywall screw head as an door/drawer knob. There is an 5cm diameter one… Chunky knob :-) And there is an 3,5cm diameter one… normal knob :-) Both has an m4 bolt thread inside so you can print it and screw it. Easy peasy…
- Downloads
- 113
- Likes
- 61
- Rating
- 5
P
PrintablesSylvain
Construction Spacer (flooring/drywall/etc)
Spacer to help with flooring install, drywall, subfloor, wherever you need to leave a space between 2 things , print without support, pretty simple. you could also use this as a calibration test for your printer, to see if all the size is…
- Downloads
- 112
- Likes
- 15
- Rating
- 0
P
PrintablesRealFakeDoors99
Irwin ProTouch Drywall Jab Saw Blade Cover Protector 2014100
Created because my drywall saw is pointy and scary. Tried @NT_1822008's model but it didn't fit my saw
- Downloads
- 111
- Likes
- 20
- Rating
- 0
P
Printablesrfengr_1
Drywall grid alternate layers Optimized for slicing
This model prints well with PETG and just 3 layers at 0.3mm layer thickness does the trick. The grid comes off just stiff enough and bendy to be inserted into wall and snap back to flat. A brass wire or screw can be attached to grid to…
- Downloads
- 111
- Likes
- 16
- Rating
- 0
P
PrintablesPlatzhalter
Unifi AP AC-Pro Drywall Moun with hidden cables
Description This took me quite some time to model. With this print consisting of 3 parts, that slide together easily, you can mount your Unifi AP AC-Pro Accesspoint on a drywall without visible cables. It uses the same hole pattern as the…
- Downloads
- 109
- Likes
- 56
- Rating
- 0
P
Printableslir
Drywall cable grommet
I wanted to hide some speaker wires and could not find any product. Please use 10mm drill to make a hole. Use hands or screwdriver to install. IMHO much cleaner look with them installed.
- Downloads
- 102
- Likes
- 30
- Rating
- 0
P
Printablesctruett3
Drywall Screw Cap
Fragile, so print extras - tiny print, printed 9 pieces in 4 minutes. Fill settings unlikely to matter, unless you only print 1 wall (which I wouldn't recommend).
- Downloads
- 102
- Likes
- 16
- Rating
- 5
P
PrintablesDIYwithJJ
Electric outlet template for drywall cutouts
See youtube video for details:
- Downloads
- 102
- Likes
- 18
- Rating
- 0
P
PrintablesYangorang
Mini / Micro Drywall Mud Pans /w Lids
Personally I prefer to keep and use drywall mud (joint compound) in a powder form rather than spackling compound because #1 it's way cheaper and #2 it doesn't dry up and expire in a month or two. You can just mix up however much powder…
- Downloads
- 101
- Likes
- 12
- Rating
- 0
P
PrintablesPaul Hatcher
(Parametric) Drywall Round Hole Protector
If you need any specific size, drop a comment, and I'll provide stl files for you.
- Downloads
- 99
- Likes
- 22
- Rating
- 0
P
Printablesbill de_cat
Drywall Knife Cover / Sheath
10-29-25 note: while this works for whatever brand of drywall knife I have and gives it a very nice fit, it may or may not work for yours. One person said it was too small for theirs in the comments and they had to cut it off. You could…
- Downloads
- 98
- Likes
- 21
- Rating
- 4
P
PrintablesOzziemandias
Google Home Mini ceeling/drywall mount (custom)
This is my custom remix of Google Home Mini inner mount. It has diameter matching the outer mount. In my opinion it look better that way. You can print it with outside circle (bigger one) laying down on textured PEI for non-visible first…
- Downloads
- 97
- Likes
- 21
- Rating
- 0
P
PrintablesKen226
175mm 7 inch Drywall Mud Knife
Print with whatever you want. A simple tool that is easy to print.
- Downloads
- 96
- Likes
- 8
- Rating
- 0
P
Printablesdankat
Drywall Access Panel Magnetic
I have a finicky dryer vent connection that I needed to be able to access to secure, and also to open up and clean, and the easiest way to access it was to cut a hold in the drywall. So, I made a 20cm x 20cm hole, knowing that this was…
- Downloads
- 96
- Likes
- 55
- Rating
- 0
P
PrintablesHappyAtom
4X! Gang Low-Voltage Electrical Bracket for Drywall | Old Work Box
4-Gang Electrical Bracket for Drywall - @claylinco generously made some variants and mods to the single gang file. There are now 2, 3 & 4 gang brackets! “I've modified it to have center markers and holes to mark the cut line on the wall.”…
- Downloads
- 95
- Likes
- 26
- Rating
- 5
P
Printablesgwendal
Makita drywall saw XDS01Z festool adapter
This connector replaces the existing adapter, to connect tightly to a 27mm cleantec festool hose.
- Downloads
- 95
- Likes
- 9
- Rating
- 0
P
PrintablesAndreas Dybdahl
Hand Sander / 125mm Disc Sander / Drywall Sander including vaccum adapter
Added a .step file for modifying the dust port to your own dust collection system.
- Downloads
- 88
- Likes
- 6
- Rating
- 0
P
PrintablesKonrad Stang
Drywall countersunk screw washer #6 size bugle head
Drywall countersunk screw washer #6 size bugle head Most countersunk washers are a true 40 or 45% bevel, this doesn't match a standard bugle head drywall screw, so I made this. I recommend to print with 3 walls There is a "flatter RARE"…
- Downloads
- 87
- Likes
- 14
- Rating
- 5
P
Printablesgexgecko
135° Drywall trowel/tool for knee walls
If you are adding a 45-degree knee-wall, but still need a tool to help with mudding/taping, you can print this one. Hold it flat to fit the 135 degree angle perfectly. Hold at an angle to use the edges independently. I printed mine with…
- Downloads
- 84
- Likes
- 18
- Rating
- 0
P
PrintablesD.Style
HSW drywall Anchor
HSW drywall Anchor , Honeycomb wall mount
- Downloads
- 83
- Likes
- 19
- Rating
- 5
P
PrintablesDirtClodimus
Home Assistant Wall Display - Raspberry Pi Touch Display 2 - 0.5 inch drywall with power cutout
This is a remix of the great Raspberry Pi Display 2 mount. It extends the mount to work with 0.5 inch drywall and makes room for USB-C power connections on the Raspberry Pi 5 if you aren't using PoE. I also thickened the magnet walls to 1…
- Downloads
- 83
- Likes
- 12
- Rating
- 5
P
Printablesklaibase
Philips Hue Motion Sensor drywall ceiling holder
Suggestions for improvement: Perhaps a thicker and slightly larger diameter cover. Maybe a slightly longer thread.
- Downloads
- 82
- Likes
- 16
- Rating
- 4
P
PrintablesJaseH
Drywall/plaster pan/tray, with rounded edges
Can be scaled down as needed. I have one that's 75% and one that's 100%. See picture --- I needed a pan for drywalling, and it was cheaper to print than buy one. I made it with all rounded corners to make it easy to clean- no more…
- Downloads
- 80
- Likes
- 18
- Rating
- 0
P
PrintablesStanley
Drywall Cutting Tool (Parkside)
Drywall Cutting Tool made of 3D printed bracket and Parkside cordless rotary tool. It's designed for Philips LED MESON functional downlight, size 95mm, 140mm, 165mm, 190mm, 215mm. Print Settings Printer Brand: Prusa Printer: Prusa Clone…
- Downloads
- 72
- Likes
- 54
- Rating
- 0
P
PrintablesGaV
Screw Setter for Drywall - Embout pour gypse
English following. Pièce à ajouter aux embouts de drill pour visser du gypse sans le déchirer. Je l'ai désigné légèrement plus petit que l'embout Phillips afin qu'il ne bouge pas lorsque je visserai du gypse. Nécessite un marteau pour…
- Downloads
- 69
- Likes
- 11
- Rating
- 0
P
PrintablesBeaver
Trimmer Drywall Hangar Hook
Onshape source model at: https://cad.onshape.com/documents/b36be7175a046d3dd8
- Downloads
- 68
- Likes
- 25
- Rating
- 0
P
Printablesex-nerd
HSW connectors for drywall screws
Honeycomb storage … ceiling? I decided to use HSW to attach some new plant lights to my ceiling (to replace the ones you see in the photo … I'l update that once they're installed). This was a good opportunity to design an updated…
- Downloads
- 66
- Likes
- 21
- Rating
- 0
P
PrintablesKenneth Connell
Bauer 16 Gallon vac to Bauer Drywall sander adapter
Included freecad file so it can be modified and used as needed.
- Downloads
- 65
- Likes
- 6
- Rating
- 0
P
PrintablesJames Tate
Irwin Jab saw / drywall saw sheath
This is a fancy sheath for an Irwin jab saw. Made it out of PETG. Fits a 1.55mm blade but should fit most saws. You can print 2 tone colours like I did (use superglue to join together) or you can just print the main body I have included…
- Downloads
- 64
- Likes
- 7
- Rating
- 0
P
PrintablesVyviora
Drywall box cutter template 72mm
A simple drywall box cutter template for two box with 72 mm distance. You need a 15x40 leveller bubble. like this → Have anice day :)
- Downloads
- 62
- Likes
- 22
- Rating
- 5
P
PrintablesGekoPrime
Hilti Drywall Dust Vacuum to Dyson Accessory Adapter
This is an adapter to use Dyson stick vacuum accessories with a Hilti VC 40-U industrial wet/dry vac. This is useful if you need to pick up large quantities of fine dust that would clog a household vacuum The Hilti vacuum is available for…
- Downloads
- 61
- Likes
- 10
- Rating
- 0
P
Printablesgexgecko
Drywall 90 degree curved/fillet ceiling support boning rib
They sell kits for this, but they are expensive, and were too thick to go around the protruding pipe in my ceiling. So I whipped up this simple support rib so I could make the curve low-profile, and re-use some of my spare drywall at the…
- Downloads
- 60
- Likes
- 30
- Rating
- 0
P
PrintablesLeo DIY
wire shelves mounting drywall back clips
print with PLA suggest printing with 5 perimeters for max strength Buy me a coffee: https://paypal.me/leositu Thank you!
- Downloads
- 60
- Likes
- 17
- Rating
- 0
P
PrintablesDanBnk
Drywall Anchor Adaptor
Drywall Anchor Adaptor for normal screws to use with "Honeycomb Gravity Broom Holder"
- Downloads
- 59
- Likes
- 5
- Rating
- 5
P
PrintablesCharlie W
Makita XDS01Z Drywall Saw Festool Adapter
Modified to add chamfer mid body to make it easier to print
- Downloads
- 57
- Likes
- 3
- Rating
- 0
P
PrintablesReed Bowman
Plaster/Drywall washer
This could be used for many things, but it was designed for supporting old plaster ceilings when repairing them. You use a long drywall screw through this into a rafter, to gently raise sagging plaster after injecting repair glue through…
- Downloads
- 57
- Likes
- 7
- Rating
- 0
P
PrintablesNT
Cover / sheath for Irwin drywall jab saw
A friction fit cover for drywall saws with 165mm overall blade length, 23mm blade width at base.
- Downloads
- 57
- Likes
- 6
- Rating
- 0
P
PrintablesFluidBadgerDesigns
Nerf wall hangers (Drywall edition)
the original wall hooks i designed were meant to be printed vertically and to use #10 wood screws for mounting. these ones are designed for 8 gauge drywall screws and can be printed horizontally for better strength.
- Downloads
- 55
- Likes
- 6
- Rating
- 5
P
Printablesfymetool
Maktia RT0700CX2 Router spacers for drywall milling
Spacers to determine the distance when milling plasterboard. The first positions the milling machine 20 mm from the rail, the second one another 26 mm for the next milling. Two-color version
- Downloads
- 55
- Likes
- 18
- Rating
- 0
P
PrintablesFusilier
Drywall Hole Plugs
I needed to clean up/fix a couple of holes in my bathroom wall where I used to have a towel rack. The holes were larger than just a small screw hole as I had used screw in anchor nuts. Also since the holes were through existing wall paper…
- Downloads
- 54
- Likes
- 3
- Rating
- 0
P
PrintablesCt6966
Drywall screw countersink
Add as negative part to make a hole for screws
- Downloads
- 54
- Likes
- 5
- Rating
- 0
P
PrintablesMarc Liyanage
Drywall Cable Entrance Hole Cover
These models allow you to cover up a 2.5" diameter hole saw hole in drywall. They have an opening for routing cables through the hole.. There are two variants, for 5/8" and ½" thick drywall. This was designed in Fusion 360, you can get…
- Downloads
- 53
- Likes
- 13
- Rating
- 5
P
PrintablesDave Hammer
Wen Drywall Sander hose to Bauer (Harbor Freight) Dust Collector
Adapter converts the smaller hose on a Wen Drywall sander to the larger inlet on a HF Dust Collector.
- Downloads
- 52
- Likes
- 28
- Rating
- 5
P
PrintablesAK3DTech
Modular Glasses Rack Shaft - Countersunk Holes for Drywall Screws
This model is intended for use with Waxpoetic's Modular Glasses Rack. I printed this with supports on, but I put a support blocker on the hex hole side of the shaft.
- Downloads
- 51
- Likes
- 1
- Rating
- 5
P
Printablesandy
Double drywall box / Trockenwand Doppeldose
A model of a double drywall box for electrical installations. This is not intended to be printed but rather to assist the designing of components to be installed in the drywall box. That is why the interior is more detailed than the…
- Downloads
- 51
- Likes
- 18
- Rating
- 0
P
PrintablesMarcElbichon
Drywall 2in Cable Gromet
Simple drywall gromets for cable management, there are a closed, open and 2 cables (8mm) version. It fit in a 2in hole. Designed for 1/2 drywall Enjoy! Category: Household Supplies
- Downloads
- 49
- Likes
- 17
- Rating
- 0