Counting matching models…
I downloaded the Free version of Eclipsons Model A. but there is the fuselage with the Landinggear not included. So i designed one to glue on the free version. it takes D3mm steelrods, wich are bended in shape. 15mm then 90° angle, then…
This printer profile is perfect for LW PLA and the planes from 3DLabprint, Planeprint, ... This is a PrusaSlicer profile, which can be used with the BambuLab X1C, because the BambuLab slicer partly does not recognize internal structures…
The original hub had the spars that connect the propeller blades printed with the hub at a position that would not be very strong and then dangerous. I created a hub part that has sparts printed at a better orientation strenghtwise. This…
The video below contains assembly scenes for the Landing Gear.
I was printing the free version of Eclipson's model A and i did not trust the CA-glue to hold the wing together between the Centerwingpart and the wingparts on the left/right side. So i designed 2 simple parts that fit in the open area in…
This also includes a nose cone
Here is a demo video of how the onboard video looks in my case: Ever wanted to equip your Eclipson Model S with a FPV system so that the experience of flying it gets close(r) to flying a real glider? Well, I did and therefore I made some…
FPV canopy for the Eclipson Cobra. The canopy 1 file was modified to have a nano FPV camera mount and wire pass-through port. The canopy 2 file was modified to have a 20x20 VTX mounting-point, an SMA mounting point, and wire pass-through…
Shock-Absorbing Landing Gear for Eclipson Model B XL Description: A lightweight and simple shock-absorbing landing gear designed specifically for the Eclipson Model B XL. The flexible main frame (printed in ASA) works together with two…
The standard anchor nut for the model C isn't great. This one takes a square nut which is much easier to fixate. The original anchor for the model C has a nut-hole that is too large for the required M3 nut, and will spin around if you…
Motor mount for a 28mm inrunner for Eclipson Spark, exactly as it says. I tried a chinese 2838 3000kv motor in the plane so I made this to fit it.
FPV canopy for Eclipson Model S. Designed for DJI O3 unit, but any vista should fit too. Features: 9g servo mount for pan holes to zipties O3 antenna mount Secure canopy in place using M4 bolt Pan tilt system is not included. Camera mount…
I liked Eclipson model A (free version), which I would like to use as micro glider. Therefore I made modifications on it like folding propeller and removable HTP. For the removable HTP, I did not modified design of existing parts (Fus5…
this model is made for install the 2814 with changed screwholes (19mm-25mm) instead of (16mm-19mm), it is modified in order to fit the longer 2814 and has a cavity to fit the longer shaft of the sunnysky 2814 suggested by the eclipson…
Designed for Eclipson Hushwing , but should fit many similarly sized models. Fits Caddx Ant Nano camera, HGLRC Zeus Nano FPV transmitter and maximum 4.5 mm diameter antenna for cheap (~$35) and lightweight (~10 g) FPV setup. The camera is…
Upgrade your Eclipson P-51 Mustang RC Plane with this integrated FPV battery cover mount , designed specifically for Walksnail systems. This is not just a mount — it directly replaces the original battery cover, giving you a clean,…
Here is a wall mount for the eclipson spitfire plane They are designed to slide right into the wings and have space at the back if you have the under wing ducts on the plane. (Note: This requires that the wheels be retracted) Screw holes:…
Designed for Eclipson Hushwing , but should fit many similarly sized models. Fits Caddx Ant Nano camera, HGLRC Zeus Nano FPV transmitter and maximum 4.5 mm diameter antenna for cheap (~$35) and lightweight (~10 g) FPV setup. The camera is…
I modified the wing parts of this model airplane to increase the wingspan by 12 cm: this guarantees a slower flight if printed in LW-PLA, or an "as designed" flight if printed in PLA.
If you're printing this amazing free aircraft model of Eclipson (https://www.eclipson-airplanes.com/g%C3%B61wolf), you'll probably feel sad if, at the very end, you notice that the shaft of your brushless motor is not long enough to…
OTHER PARTS -PUSH RODS - D1,2mm (min length 450mm) 3units -STEEL ROD - D2mm (Length 30mm) 1units -CF TUBE - D6mm (Length 500mm) 3units -STOP COLLARS D2,1mm 2units -BOLT - M3X15mm (with nuts and washers) 4units -SCREW - M2X8mm (aprox)…
It's a holder for a metal rod with a wheel and hubcaps. I highly recommend printing the wheels with 0% infill for slightly more ‘squishiness’ in PLA prints. The rest is fine with just about any settings!
i found more secure to have 2mm screws with inserts tied into the motor holder to install the motor.
plane hanger for big wheel of Model C can be rescaled for any size of wheel you have
I did not want to buy a roll of TPU just for a hinge so i designed this to be printed out of pla and super glued instead. They seem to be pretty strong and hard to pull apart even after lots of bending but I haven't done that much flight…
Gekürzter Haubenriegel für den Haube des Gö 1 Wolf von Eclipson damit der Faltpropeller. nicht anschlägt. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: Prusa PETG White…
Post of my Make of the Elipson Go1Wolf RC Plane. Hello Nick. We don't have our model there but I can give you authorization to upload the model there if you want. In the description you can put something like "This model has been designed…
I always get glue on the nuts that are included with the original eclipson pitts S12, that makes things suck pretty bad when you want to attach the wing to your model. This is a version that will take a M3 square nut, no glue required,…
A landing gear for the Eclipson PITTS S12 that will take larger 65mm wheels. Useful for when you need to lands on grass. You need to mirror all parts in your slicer for the other side! Requires a 200mmx3mm rod for strength, just like the…
Fly Baby is a 3D printable vintage RC plane designed by Eclipson: as with most vintage planes, the wings are attached with tie rods. During assembly I noticed that it is not easy to get the same tension for all the tie rods, so I used a…
