Counting matching models…
Do you have your EKET shelves free-standing? Did you forgot to buy the connection fittings? Or do you only need a few, while the swedes only sell packs of 12? This model is your solution. Print on side for best layer orientation. Print…
Do you have your EKET shelves free-standing? Did you forgot to buy the connection fittings? Or do you only need a few, while the swedes only sell packs of 12? This model is your solution. Print on side for best layer orientation. Print…
Plexiglass measurements: Front: Wide: 318 x Tall: 274mm Left-side: Wide: 224 x tall: 305mm Right-side: Wide:224 x Tall: 305mm Back-side: Wide: 330 x Tall 305 Rock decoration is printed in black PETG and hand painted.
Basit Sarkaç Hareketine Yardımcı Stant Tasarımı
Sugested print settings: Start with external layers. Legs > 20% infill Can be used for both eket and kallax - for kallax use combined sides with equal length. Part of my collection for furniture:…
My ocd was screaming after I've mounted an Ikea Eket to the wall using it's official wall mount. The gap between cabinet and wall was uneven. I didn't want to create a complete new mounting methoth to remove the gap so I just created a…
A Gridfinity base plate for an Ikea Eket drawer. The spacer is positioned at the front in my setup, as this provides easier access to the back, but it can be used either way. If your printer struggles with tight tolerances or if your Eket…
This Gridfinity spacer is a modified version of the Ikea Eket Gridfinity Baseplate , designed for fitting in an Ikea Eket drawer. In my setup, I place it at the front for easier access to the back, though it works in either position. I…
This model adds a L-shaped shelf at half-height on the Ikea Eket cube, without the need for screws. On the full side, it fits an Ikea Skubb (long one, 28x14x13 cm|11"x5 ½"x5"), it makes it easier to use the full depth of storage. If the…
Here you can find the Model Data for the spoolholders and the mounting aids to mount the PTFE feed through and the hinge for the eket cabinet.
These are the base plates (and spacers) needed for the wide Ikea Eket drawer with 70x35x35 cm dimensions. I used two 5x5 baseplates, two 5x1 baseplates and two 6x2 baseplates. I also created some small spacers for the sides and the back.…
I made these inserts for the Ikea Eket drawers, i made them for my own use, and some extra “empty” ones for multi purpose uses. If u stack two low ones on top of each other, it wil be same hight as the high ones. Passport holder has is…
Our robot vacuum kept bumping into our IKEA cabinet because it was too high for the Lidar to see and too low to drive under. That's why we decided to raise the cabinet two centimeters. the adjusting screw has to be removed from the leg…
Lifter for EKET legs so you can fit shoes under the furniture. I suggest adding double sided tabe on top of the part.
Power strip mount for the underside of the IKEA EKET storage cube Works with most EU power strips (or ones that looks similar to the one on the picture) I tested 3 different brands, and they fit them all. Mounts on the backside of the…
Print it, put a M8x50 Hex-Bolt in and replace the originale screw-adjustment. Enjoy your vacuum robot fitting below your furniture. :) IKEA Article Number: 704.289.04 https://www.ikea.com/de/de/p/eket-bein-metall-70428904/
Furniture leg (30*30*100mm) Fixed against rotation in the middle and in one corner
I used these brackets to connect several Ikea Eket cabinets so that they look better together and are easier to align. It's best to print the clamps from PC filament because it's stable and doesn't weaken under prolonged stress. However,…
Heket - Cult of The Lamb Heket's bishop form from Cult of The Lamb. Original model designed by SteD on Sketchfab, linked below https://sketchfab.com/3d-models/cult-of-the-lamb--bishops-b1ba9e4833db4d5ba8e1d6a0fb33ef75 Models have been…
I created custom drawers for IKEA EKET to store small items. Used print settings: Rails: Sunlu PLA 0.6 nozzle; 0.25mm layer height; 3 perimeters Drawers: Prusament Woodfill Linden Light 0.6 nozzle; 0.25mm layer height; 3 perimeters Drawer…
This 3D printable leg extender allows you to easily increase the height of your IKEA EKET cabinet. It uses the original screw that comes with the leg for height adjustment – simply attach the extender through the hole, and it holds…
👍 Do me a big favor and hit the Like button! ✨ Bring a warm, festive atmosphere into your home with this unique lightbox! The text “Boldog ünnepeket” – Hungarian for “Happy Holidays” – shines beautifully through the diffuser, making this…
My Prusa Mini+ fits nicely on top of an Ikea Eket shelf. This spool holder allows to keep my printer on the right-most shelf and hang the filament spool on the right side of the same shelf on which the printer stands. It just slides on…
I built a table platform for the traditional raclette we often eat in Germany on New Year's Eve. For this, I bought a wooden board and the 10cm EKET screw-in feet from IKEA. However, these were a bit too short for my liking. After all,…
The main motivation was to have something that can be stacked inside an IKEA Eket shelf but won't consume too much filament. This is obviously not as strong as having fully filled sidewalls, but it is still plenty strong for normal…
Adjustable Wall Bracket for IKEA EKET Cube Shelf This is an adjustable wall mounting bracket designed specifically for IKEA EKET cube shelves . Recommended printing materials: ABS or PETG for best strength and durability PLA+ is also…
Ikea EKET offers a nice box size with options for feet or wall mounting and it comes pre-painted. The Ikea KALLAX wasn't really designed for this but can be cut down (pictures in description) to work for this design and again is…
My first upload ever:-) I Just took the original Ikea Eket Divider designed by Dallo97 and sized it down to fit in the Ikea Eket cupboard with the 230mm depth. Still four parts. Printed in PETG and PLA aswell to divide our kitchen…
Plexiglass measurements: Front: Wide: 318 x Tall: 274mm Left-side: Wide: 224 x tall: 305mm Right-side: Wide:224 x Tall: 305mm Back-side: Wide: 330 x Tall 305 Rock decoration is printed in black PETG and hand painted.
Basit Sarkaç Hareketine Yardımcı Stant Tasarımı
This spacer is intended for use with IKEA Bestå/Eket adjustable foot ( https://www.ikea.com/no/no/p/eket-fot-justerbar-metall-70340044/ ) if you need to adjust the height difference more than the standard range. Simply place the spacer…
With this model you can build a cheap and nice-ish looking rack that's also more flexible than off the shelf alternatives with fixed width. You'll need an Ikea EKET (25 or 35cm depth, your choice) and 4x 6U or 7U posts (eg…
I wanted an angled LED strip mount to light up the inside of my IKEA EKET cabinet from the front and hide the strip for a tidy look. Found the original model, played around with it in Blender to extend it to cabinet's inside full length…
Karaktärer från den underbaraste japanska animen (TV-serien)! ^_^ Till minne av min älskade klasskompis Kristoffer. <3 Skapat av den här väldigt talangfulle och väldigt trevlige mannen: http://www.fiverr.com/rcsculpts Modellerna…
Enhance your Eket cabinet's storage capabilities with the innovative Billy MacBook Pro Voronoi Shelf Insert. Crafted from a standard 14x10" (36x26cm) Billy shelf, this insert not only maximizes space but also adds a touch of modern design…
Wall mount for Ikea Eket cabinet. Print - stick in - drill back plate - mount Can be printed two times for mounting to all four corners of the Eket. Category: Household
I have the IKEA EKET cabinet with 2 drawers under my TV and EKET base for the cabinet was around 6-7 cm high so my vacuum cleaner robot Roomba could not go under it to fetch all the dust that gets caught there. I made 4 "extenders" for…
Sugested print settings: Start with external layers. Legs > 20% infill Can be used for both eket and kallax - for kallax use combined sides with equal length. Part of my collection for furniture:…
Have been wanting a dry box system that isn't the plastic boxes and I wasn't able to find any that I liked, so here is my design. It used the IKEA EKET cabinets with the glass door. It fits 4 spools of most sizes that can be printed with…
I designed these assortment boxes for IKEA Eket drawers to hold all your screws, bolts, nuts, washers tools and everything else you can think of. They fit in a grid of 12x5. Fits standard DYMO labels on the handles at the top. Hope you…
Man braucht zusätzlich: Klebstoff (zB Sekundenkleber / Cyanacrylat) 2 Magnete Ø5mm x 10mm (oder kleiner) Zwei Seiten werden einzeln gedruckt und gegeneinander mit Kleber zusammengeklebt. Dabei oder anschließend werden die Magnete…
Inspired by this design by Glaedi Needed a way to sort my IKEA EKET drawers in my bedroom. Made these boxes in different configurations. This type of drawers take x4 in the depth. This design is meant to be printed in spiral vase mode.…
This was inspired by: https://www.thingiverse.com/thing:5388044 . Use OpenScad to modify to your needs. (The only thing that isn't customizable is the corner radius, because I didn't want to further complicate the minkowski operation and…
The EKET cubes from IKEA are great, but sometimes you want to hide something, like a router, NAS, or other ugly and/or blinky things in them. This cover wil do just that + it makes a nice “eyes of Sauron” effect at night, if it is used to…
It help me to harness better the volume of my EKETs. I printed them in PETG, with supports in the positions showed in the 3mf Screenshots. I'm a newer in the 3D print world, so i decided not to use only the bridges for not to risk wasting…
IKEA EKET snap on connector, no more no less. V2 has rounded edges for easy assembly/disassembly I have used 20% infill, made from regular PLA. Connectors are supposed to make the alignment easier. Always secure furniture to the wall !!!…
Ikea Eket mirror stand ( Ikea LOTS mirrors 12" x 12") With the right filament match, this simple design hold the mirror and almost disappear in the cube. 2 parts each side , the tallest 191mm Hardware required : 2 small wood/metal screws…
I was tired of swapping my most used PLA spools on my mk4 spool holder. I have an IKEA Eket cabinet above the printer so there would be space for hanging the spools and could print directly from there. But nothing simple was to be found…
Z powodu braku miejsca na biurku, zaprojektowałem uchwyt na słuchawki do szafki z IKEA o nazwie EKET. Uchwyt mocuje się do szafki bez śrub poprzez jej odchylenie i włożenie na tylny rant. Pasuje idealnie. Nie są wymagane żadne śruby,…
This small hook is for hanging things like wires and other accessories under your wall mounted EKET family. Designed for 0.4 noozle, wall count is 3. If you print in PETG, it is strong enough to hold things. Bracket inner size is 17.5 mm.…
Simple holder that just slides on. I recommend putting double-sided tape on the right side as shown in the third image. Print it in the orientation it is. No supports needed.
Eine Box die ich nutze um meine Sägeketten sauber zu verstauen. Die Kisten sind stapelbar und somit beliebig erweiterbar. Und selbstverständlich auch für alles andere nutzbar. Durch die seitlichen Clips wird der Stapel zusammengehalten…
Eine Box gedacht um Sägeketten sicher zu lagern und zu transportieren. Sie können natürlich auch für alles andere verwendet werden. Die Kisten sind Stapelbar und somit beliebig erweiterbar und können mit einem Deckel verschlossen werden.…
No drilling required to the EKET itself Results may vary, but if you can't connect the legs to the bracket try sanding down the seams. Wall line count: 3 Layer height: 0.2 Infill: Triangles @ 20% (5hrs++) per legs (4hrs++) per brackets…
This is one of the first thing I designed. I wanted a cable holder for my bedside table made with 2 stacked Ikea's ekets, but didn't want to screw it in or use some strong glue in order not to damage them permanently. So came the idea for…
An easy way to mount the IKEA EKET shelf to the wall. Print suggestions: 4 perimeters 4 top and bottom layers 20% infill Only hardware you need are some drywall anchors. The ones I used are pictured, but anything similar should work,…
A little 3d reproduction of the Heket's crown from Cult of the Lamb I remix the model from @ShinpiMakes_277232
Bracket for connecting IKEA Eket to IKEA Pax furniture from the back. I wanted to save the stack of Eket cubes from falling over without drilling into the wall. Since they stand next to a Pax wardrobe i designed this bracket to mount them…
Half depth shelf extension for Ikea Eket shelf cubes, designed to be half the depth of the 23cm (9 inch) deep Eket cubes. 2 part print will fit on printers with a 250mm build volume. Single part print included for extra large print beds.…
