43 models
This remix of user guillermytho 's Claws Bookmark allows an easier fit between the two bookmark parts. Spacing tolerance has been increased and is now deeper, allowing easier installation of the bookmark tab and potentially providing a…
The Sparco gear knob is a popular low cost shifter for your Thrustmaster TH8A shifter, but the fitment leaves alot to be desired. This adapter securely mates the TH8A thread to the internal diameter of the Sparco knob with zero flex .…
Not sure if your wheels need 8mm or 10mm spacers? 3mm or 5mm? Use this to test before you order a pair. Fits 4 x 100mm, 4 x 110mm, 4 x 115mm, 4 x 4.25in (4 x 108mm), 4 x 4.50in (4 x 114.3), 5 x 100mm, 5 x 105mm, 5 x 110mm, 5 x 112mm, 5 x…
Designed to be easily adjusted if needed for the perfect fitment, and works pretty well for walltaps due to the deep magnet cups! Additional hardware needed below, and pay attention to print orientations and mirroring the rear mounts. No…
Use these boards to have a tactile feel to how much you need to oversize your holes in your design to obtain the desired “tightness”. For example, with my printer, I need to oversize my hole by 0.4mm for a snug fit on circular parts and…
Tighter fitment in all aspects compared to the original by TobyMcQuack. Kudos to Toby for supplying the STEP file here on Printables.
Ice scate covers. inner size 3mm. Few more models added for bettere printing and also to fit bigger and longer blade. Still tight fit, will not fall.
You have to take the Wing off after that remove the caps with a screwdriver or knife then push the original disassembly tool inside the hole in the middle and then you should be able to take of the foot. The printed part should fit if…
This is a remix of these two excellent designs: Original design: https://www.printables.com/model/161906-voron-18trident24-hepa-filter-ex Remixed design (the one I ended up using for my own setup to fit my HEPA filters):…
Map Light Bezel for the 1972 240z. Based on Datsun 240z map light bezel by musashiz on Thingiverse. I found it didn't quite fit right in my my 72 and cracked a bit easy. I adjusted the geometry to hopefully make it fit cleaner and improve…
Test parts for testing the fitment tolererances of your printer. Well tuned filament and printer profiles should easily be capable of fitting the 0.10mm parts without problems. Test parts for 0.10mm, 0.15mm, 0.20mm tolerances included.…
he first shift knob I designed for use in my Toyota MR2 roadster. This has been adapted to sit lower and for fitment with Older Hondas using a M10x1.5 thread This design was used as a tester for a carbon fibre variant now being used in my…
24s2p p28a - Configuration for XR Super Speed battery box 19s2p p45b - Configuration for Torque / Atlow Big battery box 18s2p p45b - Configuration for Torque / Atlow Big battery box I use these in assemblies to verify fitment. I typically…
A test print to help you figure out how much clearance you need for two printed parts to fit into each other. The main peg is a 5mm x 5mm cube. The peg board has holes of the following dimensions: 4.8mm x 4.8mm 4.9mm x 4.9mm … 5.8mm x…
I added a 45 degrees ledge to support the lip of the funnel, reducing the need for supports.
A test print to help you figure out how much clearance you need for two printed parts to fit into each other. The main peg is a cylinder with a radius of 5mm. The peg board has holes with radiuses of the following dimensions: 2.5mm 2.55mm…
Convert the 16oz to 19.2 oz fitment!
This includes 3 adapters to mount a PM disc brake caliper onto your Kickbike frame using the pre-installed IS mounting holes, which are in a non-standard position. All made for the upper wheel mounting position. Included - 160mm, 180mm…
25mm, 20mm, 15mm, 10mm Using the following options: pcd = 98 bolts = 5 bolts diameter = 12 diameter = 149 hubdiameter = 58.1 thickness = 10, 15, 20, 25
Used to get power from the 12v pads on the Moza wheelbases, I used the screws, springs and nut from the horn connector on the Kyostar through the holes to face the pads. I then cut an old pen spring in half, soldered that to a red and…
Print body bottom up 35% Infill support structure: Normal Support Placement: Everywhere Overhang angle 45 degrees support density 10%
Just a remix with more room/height so cable won't bend so much
Settings I used: Infill: 20%, cubic Walls: 2 Top and bottom layers: 3 Supports: Tree, everywhere Nozzle: 0.4 mm Layer height: 0.2 mm Tested on: Ender 3 V1 Direct drive Creality PLA 200C nozzle 50C bed 3 mm retraction A possible foreseen…
This is a small magnet test for figuring out tolerances. It is what I used to figure out the magnet holes in my AnkerMake bins. You can tilt the tool and add supports to make it print wonky, replicating what it would be like to print a…
This is just the post for the lever, the cross pattern should fit nicely into the Danco HYR271T Hydroright dual flush lever mechanism. This was designed to fit with the pinball flipper…
Added too the 3mf file in case somebody wants to optimize it.
The .3mf file contains 3 plates so that it's easier to print the ID and OD gauges in different colors if you want. If you want them all the same color, just use the one plate that contains all of the gauges.
Shaker tops for Penzy's Spice Company jars. Their short empty jars do not have fitments. Their jars have about 1/2mm variation so there are small and large diameter lids. Each diameter size also has a small and large diameter hole size…
This model is a mock-up of the water dispenser cavity of some GE Fridge models (GNE27JYMFS and GNE25JSKCFSS) to test fitment with custom water dispenser faceplates.
This print is designed to dial in the exact tolerance you need between parts in both the vertical and horizontal plane. This is important as 3d printers stack layers and the dimension and tolerance will be slightly different depending if…
I often find that standard shaker fitments for spice jars have holes that are either too small, meaning I take it off and never find it again, or too large and I end up pouring WAY too much out at a time. When I recently reorganized into…
I copied bipsen's design and modified it to be easier to print, and fit the specific pneumatic fittings I have. Category: 3D Printer Accessories
Use as a spare part or for other sieve sizes. There are 2 different models, one for printing TPU 95A and one for printing PETG. Size Suitable for spice jar as shown in the screenshot of the sketch (outer diameter 31 mm). 7 Holes, diameter…
40mm Flywheel cage for the Strike Force Blaster. I have only tested daybreaks in this cage and work with no issues.
This project was designed to replace the OEM Non Refillable Fitment that was discontinued from Bacardi Rum bottles. (Shown Below) I have designed multiple versions that are in testing, however, the model featured here is a concept that…
Hope this works it is V1
This includes 3 adapters to mount a PM disc brake caliper onto your Kickbike frame using the pre-installed IS mounting holes, which are in a non-standard position. All made for the upper wheel mounting position. Included - 160mm, 180mm…
This print is designed to dial in the exact tolerance you need between parts in both the vertical and horizontal plane. This is important as 3d printers stack layers and the dimension and tolerance will be slightly different depending if…
I added a 45 degrees ledge to support the lip of the funnel, reducing the need for supports.
I often find that standard shaker fitments for spice jars have holes that are either too small, meaning I take it off and never find it again, or too large and I end up pouring WAY too much out at a time. When I recently reorganized into…
Not sure if your wheels need 8mm or 10mm spacers? 3mm or 5mm? Use this to test before you order a pair. Fits 4 x 100mm, 4 x 110mm, 4 x 115mm, 4 x 4.25in (4 x 108mm), 4 x 4.50in (4 x 114.3), 5 x 100mm, 5 x 105mm, 5 x 110mm, 5 x 112mm, 5 x…
Hey, i would like to share with you this prototype of a wheel measuring tool. You will need: 5x M3 heat inserts (8mm or smaller) 3x M3x10mm Socket head screws 2x M3x10mm Flat head screws Usability: 13" - 25" Wheel size 6" - 16" Wheel…
![Voron 1.8/Trident/2.4 HEPA Filter Exhaust [Remixed fitment with 3 filament input holes]](https://media.printables.com/media/prints/426876/images/3532794_4cd38264-6965-4d17-8da1-91bd6c75d816/pxl_20230316_173042702.jpg)
