Counting matching models…
I took the Pinecil/TS100 Top Large B insert from the original case and modified it to hold the CNC Kitchen Heatset tool and tips. I also changed the stand holder to be easier to remove by pressing on the base.
The Fraks Flexarm is a tool-balancing arm designed to keep the attached tool parallel throughout its movement. It was created to hold soldering irons to install heat set inserts into 3D printed parts. It has a large working area for its…
Very small bed leveling knob that uses heatset inserts. They were modeled originally for the ROOK 3D printer, but I thought I would share them since I think they work nicely. Very fast print as well.
I used the following one, i can't guarantee that all AliExpress versions will fit though. https://www.aliexpress.com/item/1005006503495825.html?spm=a2g0o.order_list.order_list_main.16.13111802lsBWzr This will fit the M2, M3, M4, M5, M6…
The mounts are work in progress. I used a 10x20 cable chain to fit the cables and the hose of the air assist: https://www.amazon.de/dp/B08R1LFZTN?psc=1&ref=ppx_yo2ov_dt_b_product_details Used these belt clamps (one especially on the X…
Edited the single honeycomb to allow for a M3 Heatset Insert
This is my first attempt at modeling something. I wanted a case that could fit at least 10 SHORT tips + all of the aliexpress brass heatsets. This includes a slot for the M2.5 heatset. It can hold up to 4 standard length tips, 2 near the…
I printed 3Daomm's M3 wallet in december 2021 and had 2 major ideas for improvement: Heatset inserts to avoid screwing into plastic. Creep and forces on screws in plastics are not my best friends. The lever actually had 7 steps despite…
New version 2 of my duct is live, I have adjusted the spacing where the heatsert goes and closed the front. The fan should fit snugly onto the colums where the heatserts sit. Then you use 2 m3x16 BHCS to secure the fan. Much cleaner and…
I wanted a Heatset Insert Press and I realized that I have a Dremel Drill Press that I haven't been using - Thought I'd be able to make a little adapter for a soldering iron. Just about any of the inexpensive Amazon soldering irons will…
This insert takes the original “TS100/Pinecil Top Large” insert and adds storage for all 7 heatset insert bits that come with the AliExpress tip. Also has a bit larger tolerances, which makes it easier to remove the small bits.…
This model is optimized to use heat set inserts and also removes the unnecessary screw in the middle of the cassettes. This only includes models for the filter cassettes, for the rest of models needed for this project check out the…
First of all thanks to Chris for the original version of this great handle! Its a nice big handle that fits big printers like a Voron V2 and Trident perfectly. Since I like sturdy screwed parts more I created this version using the…
Test your Inserts This object was created to experiance my first heatset inserts in 3D-printed designs. Since i just started using these in my designs, i wanted to know how i have to design the holes for the inserts to get the best…
A 3x1 Gridfinity Storage Container for CNC Kitchens TS100 Heatset Insert Tip in the Sizes M2-M8.
A TS100/TS101 stand for HSW with additional pockets for the CNC Kitchen heatset insert tool bits. This one should be printed upside down (as oriented in the STL) to allow for the HSW plugs to be properly printed.
It takes a scavenger hunt to find an acceptable DragonUHF adapter for EVA3. And the one I found has cable-routing issues. I modified it to give extra space for the heater cable to come out the side. It's still not perfect but it's good…
In this mod, the short Mech is V2 modified to receive 4x m3 heatset inserts. The Spin Ring V2 is modified to receive 1x m3 heatset inserts. This avoids the need to directly thread M3x12 into plastic. Direct-thread M3s are…
PATCH NOTES 02/09/2023: ADDED MODEL NOW WITH LABELED LOCATIONS Printed in PETG 0.2 , 15% infill - line pattern. Designed in Onshape
I wanted M3 heatset inserts for mounting the upgraded hotend fan for my Ender 3 V3 SE. Ended up remixing the fan adapter from KILLbabylon to size the 40mm fan mounting holes out to 4mm to use the heatset inserts. Thanks KILLbabylon for a…
This is an insert for the Dewalt Tough Case to hold the Pinecil and CNC Kitchen Heat Set Insert kit. Also included is a simple corner divider and dovetail test piece. Fusion files are included if you want to modify them.
Modified fan mount for using M3 brass inserts
Added heat set inserts to the filament guide slide. Having to adjust that depending on spools will wear out the threads in plastic fast.
I've been using more and more Heatset inserts in my projects recently and have been wanting to build one of the many soldering iron press designs that are out there on Printables, but couldn't decide on which one would be perfect for me.…
I'm a sucker for heatset inserts, and I figured if you're occasionally maybe opening the device, might as well put a heatset insert in there, remove the chance of breaking plastic threads. This remix was made with CNCKitchen's short m3…
For the UHF stealthburner cover with CPAP and two piece PCB I loved this original/remixed design that was able to use a 2-part PCB for the CPAP Stealthburner cover but I was unable to fit any heat set insert I had. The cpap hose adapter…
Heatset threaded insert I'm using can be found here: https://www.amazon.com/gp/product/B08PVQX853/ Reinforced the area the insert goes into. Everything else is the same as their original design other than the insert hole and the inset…
Use one M3x4x5 heatset insert on each side. Prints fine on it's side without supports. Feel free to comment if you want a different size, or make it yourself using the OnShape CAD files
PLEASE POST A MAKE OR A COMMENT IF YOU USE THIS FOR A LONG TIME. I NEED FEEDBACK IF THE OPENING IS TOO BIG FOR THE INSERT. I would like to point out the difference between this model and this other version found here is that this one…
This is a remix that lays the tips flat in order to allow it to be stacked or put into box.
My Thanks the the Multiboard Team over at Multiboard.io if you haven't checked them out then you should. all parts were printed on a Centauri carbon using Elegoo PLA Rapid Plus with standard settings. no supports are required. I will not…
This is a remix, I made the heatset tools fit better, the lid to close nicer, and all tolerances are made for printing with abs/asa in mind. The heater pocket is too big, so it will fit all variances described in the original holder. No…
I wanted to make the already awesome H2T case by Muzi a little more robust by adding a heatset insert to marry the two halves together. Here is my rendition of that. You will want to use an M3x5 thin-wall heatset insert. These are the…
Heatset inserts (M3 thread, 4mm length, 4.5mm outer diameter, 3.9mm nub)https://www.aliexpress.us/item/3256805034317562.html M3x10mm button head screw See original model for printing instructions. You probably want extra walls so there's…
I wanted to equip my TS100 Case with the inserts from jamie xu and Char to accommodate both my desoldering pump and my CNC Kitchen Heatset. Unfortunately, the TS100 collides with the stand holder due to the customisation of Char , so that…
Remix of the great yet simple mount from Tom. Added heatset insert holes on the bottom side of the mounting plate.
Basically a GridFinity (by Zack Freedman) holder for Hakko Heatset or soldering tips.
I really like Sneak's design for the ball camera mount, but wanted to be able to secure with an M3 bolt instead. The ball is the same as in the original design, so you can re-use the Pi Camera case from sneak's design.
Here This is based off the latest 0.4 Beefy lulzbot Idler variant (which compared to 1.4c is basically 2.0 anyways), licensing is Creative Commons Open Source Attribution as usual. Please feel free to use this part in any manner you see…
Couldn't find an adequate MGN12H dummy carriage to be able to mockup my toolhead before I have linear rails. Uses 4 heatset inserts, print standing vertically as shown. BOM: 4x M3x5x4 Heatset Inserts (Voron spec)
I bought some M5x5.8mm heatset inserts that I wanted to use, this seemed like the perfect usecase for them. Make sure the mating surface between the bearing and the heatset is flat, if any pieces of plastic stick out they might impede the…
NOTE: this model is toleranced for SLA printing. It was edited in Onshape and I have parametarised the m3 holes, bearing slot and captive nut slot. The parts which I have edited have a prefix “EDITED” the rest in the onshape document are…
14/01/2025 Added step file for the drill press. This is a mount for a Parkside Soldering Iron on a Parkside Drill Press for helping with heatset inserts.
Print settings were 0.2mm, 0.4mm nozzle, 3 walls, 5 top and bottom layers, 40% adaptive cubic infill. I used the octogram spiral bottom infill pattern as well. These parts were printed in ABS and the hole sizes work accounting for the…
The Ultimate Spool Holder, remixed to use "voron standard" m3x4 short heatset inserts instead of m3 nuts.
Takes an M3 x 5 x 4 heatset insert, inserted from the back to prevent accidental pull out.
Buckets are available with the original This goes for every printed/plastic thread, do not overtighten it, even tho these ones are a bit more resiliant. Same print settings as the original: support generation needed for the area where the…
Solves the constantly breaking thumb screws.
Gridfinity bin for CNC Kitchen threaded insert tips and TS100 adapter
I modded the original Cynthia to utilize heatset inserts as well as a few tweaks here and there.
Several sizes and flavors of Voron themed heat set pencil cups. Both large and small. I have remade these a few times and have been asked about them so I figured I would post them online this time.
I have noticed my extrusions are not consistent, if you find they are too lose when you print, (test before you place the insert, in case you need to reprint) You may need to scale the part up 1% Have you ever gotten done with a build,…
EBB36/NH36 mount with strain relief
I wanted a heat-set insert press, but couldn't find any that matched my requirements: Used as few “special” hardware bits and bobs as possible. Be as compact as possible. I don't have lots of storage room, so something compact, but easily…
I merged the carriage from both these designs to create a carriage that would support a WLC100 and work on the fully 3D printed press.
60mm fan mount for Voron Switchwire with M3x5x4 Heatset inserts
Print with top side down
I already have storage for my wicks/spools, so I figured I'd replace that space to actually get some use out of those free screwdrivers I've amassed about 20 of. Now that the screwdriver moves with the iron, I won't forget it and be left…
MMB Enclosure for ERCF or Tradrack with magnetic lid Required 10x M3 Heat Inserts - M3x5x4 (Voron spec) 4x M3x8mm SHCS 6x M3x12mm SHCS 1x M3x30mm SHCS 2x M5x10mm SHCS 2x M5 T-Nuts 8x 6mmx3mm round magnets
This is a remix of https://www.thingiverse.com/thing:4909602 . I have modified it to use the 5x4x3 Heatset Inserts used in the Voron builds. I made the base 0.5mm thicker so you can use an M3x6 screw to assemble it with. update12/22/21…
I am looking to grow my new channels! Give me a follow on youtube and mastadon! and please feel free to say hello :) https://www.youtube.com/@homegrown3dprint https://mastodon.social/@homegrown3d From Article…
A simple 1x1 gridfinity bin for the Hanglife heatset Insert tips. The bin holds 7 tips plus the 900m adapter
Remix of the DIN Pi with M2.5 heatset inserts instead of M3. M3 screws don't fit the Raspberry Pi (M2.5 is the recommended screw size) and since there is not a lot of instructions to build the electronics box of the Mercury One.1 I…
This mod is for 3mm or 4mm acrylic glass with 3mm thick foam rubber band You can get the borsch reward for the handle here https://www.printables.com/de/model/407357-voron-door-handle-heatsets/files If you are interested in other acrylic…
This holder mounts on a Skadis pegboard using TNuts (2.5mm). It holds 5 heatset insert bits in sizes 2, 2.5, 3, 4, 5 mm. The unit is in two parts allowing you to remove the main holder to take to your work area. The pics above use PETG,…
This is a 3D printed gt2 20T pulley. It can be fixed to a D-cut or regular shaft using a heatset insert. Unlike metal pulleys, it should be used in places that do not require strong torque. I created it for use in an incremental encoder.…
My original Bed Stop Rear cracked when I screwed the CoreXY assembly to the Backplate. The plastic in behind the square nut was too thin and weak to take the force when tightening the screw through the back. First, I only wanted to print…
Original SV08 Top Extension kit with but closed the triangular vents in the original model to keep the enclosure heated. Also added an option for M3 heatset inserts for bolting either stacking extensions, or other accessories. Also added…
Added a slot for an ID card on the inside of the flip-out top part (see picture). Wallet now uses standard 6mm tall heat set inserts for longevity of threads. Credit card slot was slightly increased in height so cards fit looser and slide…
I modified to fit a M4x10x6 heatset insert.
The original mount using the m3 square nut can now be used as a heat set insert. I've been using it for a month and haven't had any problems! The original model requires 35mm bolts. However, the heatset insert requires a bolt of about…
I really like the original model for this but I wanted to be able to remove the cover without the little pins breaking and having to reprint it. I also removed the small fins between the usb sockets because they were so thin they just…
Update 2024-12-30 Added the Front CoreXY parts with heat set inserts corexy-front-left-r5_mod corexy-front-right-r5_mod Update 2024-12-13 Updated the top parts left and right sides: added a missing screw hole (for heatset insert)…
As I needed a hook/mount for my Index headset near my simrig i designed this. It has been working very good and keeping dust out of the headset because of the orientation. For mounting on 40x80mm aluminium profile with M8 screws. A…
Remix of the model, fixed the sizing of the M2.x, M3, M4, and M5 bits to have the proper sizing. No longer do you need the finder strength of world class climber Alex Honnold to remove a bit.
Kept breaking the clips and decided to add more material and (2) M2x6 screws to support the clip
None of the bins out there would work for the tips that came with the heatset insert tool I purchased (a cheap 6 letter from Amazon) putting it here in case it works for someone else. Sharing under GNU since Zack has made Gridfinity GNU…
This is a mashup of a Pinecil mount at attach to a USB microscope stand to reuse the stand as a heatset press. Get the clamp-cover from https://www.printables.com/model/719559/files the pinecil clamp page and I also recommend the taller…
This is the beginning of a growing list of different spider vanes for the hadley telescope. I plan to add many more variants going forward. Spider vanes hold the secondary mirror in place in the center of the UTA assembly. The shape,…
Compatible with 5.7mm or 4mm length M3 heatset inserts. Hole has tighter tolerances to improve insert adhesion. Before installing the carriage make sure the extra material ejected from installing the heatset insert is removed, ideally by…
Remodeled version of SKR 3 EZ Mount for Voron style Heatset Insert
This is a remix, pause before layer 39 to place magnets.
Remix of the model, The letters are printed in relief so the reading is easier. adapted for BAMBULAB with AMS system.
My inserts were for a 4mm hole, 5,7mm deep. Use M3x10mm DIN912 Hex Socket head cap screws.
The original model is excellent, but it requires screwing directly into the case, which isn't great if you want to disassemble and reassemble the case many times. This remix enlarges the holes so that it's easy to accurately position M3…
Introduction This is a remix of the Open Stick by TheTrain. A year or two ago, I was interested in making an enclosure in the conventional way that one would expect (unlike my weird vertical print). I made this model from scratch, but I…
This allows the use of standard M3x5x4 threaded heatset inserts instead of screwing direct into plastic.
I liked the press, so I made an adapted head to make it compatible with my pinecil. Assembly procedures are basically the same as the original model
A heatset insert press made from some extra parts I had laying around. Uses 4 smooth 8mm rods, 6 Lmuu8 bearings(can get away with 4 or 5 though), 12 m2 screws(8 that are 6mm long, 4 that are 10mm long, though can be longer), it also uses…
The soldering iron holder may need modifying to fit yours. PRINT THE PARTS CLOSE TO THE SOLDERING IRON IN APPROPRIATE FILAMENT Required Components: 4x m6*8*6 threaded inserts 2x m6*20 screw 2x m6*28 screw 4x 8X 46mm external loopended…
Skadis tray for the CNC Kitchen threaded insert tips used with the TS100/Pinecil adaptor. Print in the orientation that it will mount and it should not require supports. This attaches with the Skadis Universal Hook by CSD_Salzburg.…
Print with the widest part facing the plate. BOM: 2 x heatset inserts 2 x SHCS M3 x 8MM screws
The hole is 3.7mm wide by 4.6mm deep. Make sure your inserts are about 1mm wider than the hole (so there's plastic to grip) and not as deep.
I required a some precisely positioned heat inserts so I designed a new heatset insert press around what I had lying around. It is all printed in plain PLA but I will have to reprint the Soldering-Iron mount in ABS or PP so it does not…
MMB V2.0 Enclosure for ERCF or Tradrack with magnetic lid Required 10x M3 Heat Inserts - M3x5x4 (Voron spec) 4x M3x8mm SHCS 6x M3x12mm SHCS 1x M3x30mm SHCS 2x M5x10mm SHCS 2x M5 T-Nuts 8x 6mmx3mm round magnets
Device for pressing threaded inserts into 3D printed components with a soldering iron part list: 4 x Linear Ball Bearing 10 x 19 x 29 1 x SREMTCH Soldering Iron (200°C - 450°C) 2 x 10 mm x 300 mm Linear Shaft Straight Round Rod 10 mm…
I designed these simple tools using Onshape I wanted something to test my heat inserts against, so that when designing new models I could get all the hole sizes correct. They are all made using 0.1mm increments, so you can use them for…
I needed to mount something to a peg board but didn't have any small bolts or nuts but I did have M3 cap screws and heatsets, so I created these to save a run to the store. Conical washer is in two sizes: 10mm and 15mm diameter. Heatset…
Support for Parkside
![Sherpa Mini Captive Nuts instead of heatset inserts [SLA tolerance]](https://media.printables.com/media/prints/346945/images/2953567_eff3efb2-2dac-43da-849f-7160c3833b16/pxl_20221222_212349494.jpg)
