Counting matching models…
The Kukirin G2 is a well-built electric scooter, but for some reason, it only comes with a low-quality rear fender. To protect the shock absorber and myself from water, I made two fenders: one for the front, secured with two screws, and…
There is a small torx screw in the adjusting nut that needs to be removed first. In my case the screw was hiding in the back of the nut so I had to use a bit of force to loosen the nut so the screw would show up. I printed it with 4…
Porte clé Kukirin en relief pour les trottinette de la gamme.
Zpevnění pro Kugoo Kirin pro 2021. Pro řídící tyče 60 x 37mm. Tisknuto PETG s výplní min 30% a 10 perimetrů. Logo na vsazení do záslepů tu mám taky.
Kukirin g2 mud guard / rear fender extender Clips in - no glue or zip ties needed. It clips in on the sides (bottom part). Printing recommendations: At least 15% infill, PETG/ASA/ABS but PLA will work too. Supports needed. I printed it…
Settings for 0.4mm nozzle: First layer height: 0.14mm Layer height: 0.1mm Layer width: 0.36mm Nozzle temp (for PLA): 200C Nozzle temp (for PETG): 235C Bed temp: 65C Recommended using 0.4mm nozzle or smaller. This keychain doesn't have the…
Kukirin g2 front fender / mud guard Clip on - 5 seconds installation. As a bonus, here is my silly design process:
Rear extension fender designed for the KUGOO Kirin G2 New (2024/2025) electric scooter. This 3D-printable part provides extra protection against dirt, dust, and water splashes coming from the rear wheel. The model has a reinforced…
For Kugoo F3 pro max
Tired of mud and water splashing everywhere on your Kukirin G2 MAX? Upgrade to this custom-designed fender for ultimate protection and a unique aesthetic. Unlike the default fender, this one is engineered to shield against the elements…
Screw cover for the Kugoo Kirin G2 Pro
min 40% infill supports required TPU material
I am currently testing this version. Print at your own risk! (normal size) Short version: Already tested and working. Not compatible with version 2026 After 80 kilometers my front fender broke (normal size fender - PLA material) . I hit a…
If you had to take apart the front/rear shock absorbers, you know that the holes to release the shock absorber are just covered with a sticker and re-sticking is not possible without glue, so I made a simple hole cover. Printed with PETG…
3D model dimensions: washer 20mm, washer height 1mm, seat 16.5mm, plug height 6mm, recommended plastic PETG
I was fed up with the fact that when I tried to put my G4 on a stand on a softer surface, it would fall to the ground. So I modeled this. For assembly you need: 3x - M3x12 screw Allen head 3x - M3 nut Adhesive material, such as silicone,…
I printed it on PETG plastic, but you can print it on TPU or flex if you need flexibility. Stick it on with double-sided tape or glue compatible with your plastic.I printed it on PETG plastic, but you can print it on TPU or flex if you…
Already tested and working 200+ kilometers - Upper part with reflector (PLA material) If this fender lasts 200 kilometers without any damage, then I will update this description to already tested and working. ;-) You can choose from two…
UPDATE 02.01.25: added .STEP file, the 7 round capacity with holes. UPDATE 01.01.25: improved the follower's design These are based on the original geometry, so they should be compatible with the Kirin type A, the Wrenfield and the…
Extra 2 headlights for Kukirin G2 electric scooter
This is a custom-designed mount to securely attach a Kryptonite Evolution Mini-7 U-lock to the frame of a KuKirin G2 Pro e-scooter. The basic idea is from here:…
I remade the shroud from scratch then made the shroud big enough to allow for a BCAR. It can probably fit any BCAR but I've tested with the Worker BCAR without sleeve, ex BCAR, and ex BCAR rev2. Print Instructions: 3-4 walls, 15% infill,…
No rattling noises and easy to fold. Printable in 3 hrs in PLA with: 0.20 layer height. 5 layer wall loop. 20% infill in honeycomb 3D (30% infill for FOLDING BRACKET) EXTRA STUFF NEEDED x4 M4 x 8mm nuts and bolts (to fix collar to stem).…
I don't use a seat with my KuKirin G2 pro, and the 4 mounting holes remain uncovered. I designed simple plugs for them - you should print 2 threaded and 2 without thread. IMPORTANT! Be careful when screwing in the threaded plugs - they…
Logo k vytištění ze 2 barev Kugoo Kirin. Na zpevnění, které jsem tu také vložil, lze jen vsadit, drží i bez lepení. Přívěšek na klíč Kugoo Tisk PLA
I purchased the bottle holder and bottle at Decathlon.…
This part is a bit wider than the original Kugoo shockarm cover and should stay inplace without any glue as opposed to the original one. I printed it from ASA to tackle weather conditions but the filament choice is up to you. The original…
Son unos guardabarros ponibles con clips en los guardabarros del kukirin g2 pro (patinete eléctrico) Preferiblemente petg con recubrimiento uv para no daño por exposición al sol. Miden 0.5mm de espesor ideal para poder doblarlos a mano…
ABS+ 5 perimeters M6 bolts and nuts M3 bolts and nuts locktight
Simple 80 mm coaster with a Kirin symbol on it, from WoW
There is this bug on Kirin Type-A first batch, the mag could've been over inserted, and stops bolt closing. It is said the later batch would fix this problem by the manufacturer, but here is an easy fix solution: Just add this 3D printed…
Converts the Kirin angled talon magwell (from Shellington Labs) to be single dart loading. In prep for a no-mag event, I found I didn't have any old-school blasters at the right FPS. There's a single load mag block for the SLAB and that…
Print using PA-CF or PA-GF with at least 5–7 walls and 35–40% gyroid infill. Print the front part without supports—it is designed with sacrificial layers. Print the back part with supports, using the orientation shown in the orca…
It hooks in on one side and snaps into place on the other; I recommend printing it on its side, with supports, to prevent the hook from breaking, PETG works well
Crash pad na nakrętki 21mm, hulajnoga kukirin Różna wysokość Nut 21mm
Use 25-40% infill Secure splashguard with screws into the frame
This is a blank cartridge intended to be used with any springer that takes shellington flypoint shells. Do NOT use these for the flypoint or any flywheeler, as they are not designed to shoot anything out of them. It is recommended to fill…
Fő Jellemzők: Optimalizált dizájn: Pontosan illeszkedik a gyári Kukirin G2/G2 Pro hátsó sárvédő ívéhez [1.1]. Funkcionális és esztétikus: Diszkréten illeszkedik a roller megjelenéséhez, valóban jelentős funkcionális előnyt nyújt. Tartós…
add some solidol/lithol inside so that it does not jam the spring P.S: I recommend drilling to 6 mm and using M6x25 screws and accordingly nuts
Converts the Kirin angled talon magwell (from Shellington Labs) to be single dart loading. In prep for a no-mag event, I found I didn't have any old-school blasters at the right FPS. There's a single load mag block for the SLAB and that…
add some solidol/lithol inside so that it does not jam the spring P.S: I recommend drilling to 6 mm and using M6x25 screws and accordingly nuts
link to mini kukirin g4 https://makerworld.com/en/models/2284410-mini-kukirin-g4?from=search#profileId-2491494
Settings for 0.4mm nozzle: First layer height: 0.14mm Layer height: 0.1mm Layer width: 0.36mm Nozzle temp (for PLA): 200C Nozzle temp (for PETG): 235C Bed temp: 65C Recommended using 0.4mm nozzle or smaller. This keychain doesn't have the…
ABS+ 5 perimeters M6 bolts and nuts M3 bolts and nuts locktight
Already tested and working 200+ kilometers - Upper part with reflector (PLA material) If this fender lasts 200 kilometers without any damage, then I will update this description to already tested and working. ;-) You can choose from two…
This is a blank cartridge intended to be used with any springer that takes shellington flypoint shells. Do NOT use these for the flypoint or any flywheeler, as they are not designed to shoot anything out of them. It is recommended to fill…
The stand on the Kukirin G4 has no support and in the unsupported position it can slightly flop up and down and when you drive on a bumpy road the rear part of the stand always hits the lower part of the scooter's body. (and that makes…
When drivinig with my todler she accidentally kept pressing the power button on the Kukirin G2 Max e-scooter. So i designed this button protection against unwilling presses. The cover stays in position by a spring and it is very easily…
a muzzle brake for the shellington kirin type A. you'll need three m3 screws, 10mm should work fine. there is also a version that uses heatset inserts for extra durability. there's also space for Rifling devices, tested and confirmed to…
This is a replacment plungerhead for the Shellington Labs Kirin Type A. A friend has the blaster and their plungerhead cracked. This model was quickly thrown together and printed with PETG as a replacement part. The printed part has been…
If your rubber one broke off, (like mine) you can use this one it is tested and fits tightly. (But not too tight)
To connect the two parts on the scooter rack, 2 screws and 2 nuts are required, printed with 4 walls with a filling of 25%
When charging your electric scooter the transformer of your charging cable can easily overheat, so I made these risers to keep the transformer from overheating in the way it keeps it uninsulated. How it does it is by not using the surface…
Fender support part for Kukirin G2 Pro. Printed it with Bambu Lab PETG-CF. Slicer settings: 0.2mm layers; 4 perimeters; infill 40% gyroid; laying down on the broadest side; supports needed.
It is necessary to extend the line from the rear LED-light 16 pin block: Black – GND (General contact) Yellow – + Turn right Green – + Turn left
It is necessary to extend the line from the rear LED-light 16 pin block: Black – GND (General contact) Yellow – + Turn right Green – + Turn left I used this 12v socket
16 pin block: Black – GND (General contact) Yellow – + Turn right Green – + Turn left
Before printing, measure your key. In the picture below is a long 35mm (model MON1SP)
first of all you need to cut off the existing hex protection and what was torn off and also increase the hole to 10mm
A mount for holding your chain lock. ABS or ASA material is recommended for outdoor use.
This is a replacement power button for the Kukirin S1 Pro electric scooter. The original rubber button on these scooters often breaks or falls out, making it difficult or impossible to turn the scooter on or off. This model has been…
this is a peg that goes on the nut and make the scooter look better
Steering bearing protection to reduce water, dust and sand ingress P.S.:Before printing, measure your gap.
PRINT infil: 100% material: PETG time: 2h HOW TO INSTALL bend like on the picture push down click
16 pin block: Black – GND (General contact) Yellow – + Turn right Green – + Turn left
you will need you will need: 2 bolts M5x10 or M5x12 2 nito nuts M5
CZ: Držák bagu WildMan pro koloběžku KuKirin G2 Max. Vytisknout 2x EN: WildMan bag holder for KuKirin G2 Max scooter. Print 2x
Print with 20-40% infill Use supports (Regular or Tree) Use zip ties to secure fender to the Kukirin G2 Escooter
Use supports 20-40% infill Zip ties are needed to secure the fender to the scooter
Use 20-40% infill for good strength Use 1/4" by 2" bolts to secure the bracket and bar to scooter
link to mini kukirin g4 https://makerworld.com/en/models/2284410-mini-kukirin-g4?from=search#profileId-2491494
Charging port cover for kukirin m5 pro made with PLA 30% infil
Description: This is a self-designed turn signal for the Kukirin G2 Pro scooter. In principle, it works on any scooter that has 12V indicators – or on any scooter where you have 12V and can add a handlebar switch and a suitable flasher…
A plug for the charging hole, making it difficult for water to get inside. Gasket. For scooter Kukirin G2 Pro (but there is big chance to fit it to other typs of scooter). Versions: -charger_plug_v3 - with small cut at one of side. With…
KUGOO KIRIN M4 PRO steering bushing for the 2023 model. The steering bushing broke, causing play to appear. I took the measurements myself. Now there is no need to go for service.
