P
Printables
držák nabiječe ledlenser Tatra Terno
Nutno trochu přibrousit aby drželo pevně
Search results: ledlenser
Counting matching models…
P
Printables
Bike flashlight holder (Ledlenser T7.2 or similar)
First I made a version that is held down entirely by velcro strap, but realized that PETG work great even without a strap, so I made a version that can be held together with a glue. Some might prefer velcro version as it can act as a…
P
Printables
Skadis Ledlenser P7R Stand
This is a simple stand for your LED Lenser P7R. The stand can be mounted to a IKEA SKADIS Wall.
P
Printables
Ledlenser MH7 tri-glide buckle
A replacement buckle for Ledlenser MH7 LED flashlight. Should work with any other similar strap. Tried to model it as close to the original as possible, there are some deviations, feel free to modify it. Printing Instructions Use PETG,…
P
Printables
Würth Ledlenser P7 Rebuild/Upgrade
The files consist of an adaptor for a Convoy 1288 switch , an adaptor for a 16mm LED and finally a slieve for a 18500 LiIon cell. With those parts I was able to put a 10W Cree LED in the good old LEDlenser body. Don't forget to order some…
P
Printables
Ledlenser P5R Flashlight Multiboard Holder
This is a Multiboard holder for a Ledlenser flashlight model P5R. It uses a single press-fit Multiboard peg. I don't know if other Ledlenser models will work with this, but the handle diameter is 22mm for reference. Prints in place…
P
Printables
GoPro adapter for Ledlenser Headlamps
I've made this to mount a Ledlenser HF6R headlamp on a RockRider Expl 500 bicycle helmet by Decathlon. The model is split into two parts to make printing easier and to be able to use two different layer alignment for improved part…
P
Printables
LEDlenser H14R.2 Case
I created this case for my H14R.2 head lamp so it won't accidentally power up inside my pack. The case is part of a set of cases I created for different stuff I use as an event technician. The lamp needs to be twisted 360° against the…
P
Printables
Petzl Vortex Helmet Adaptor - LEDlenser H14R.2
I designed this adaptor to my Petzl Vortex helmet so I can mount my LEDlenser H14R.2 to it. It can also be used as a base for designing mounting brackets for all kind of stuff. The parts are connected with M3x20mm sink head screws and…
P
Printables
Ledlenser K2 holder
A holder for the Ledlenser K2 torch. The holder attaches snugly to the flat parts on the side of the torch. If you find the holder to not be tight enough, the the "tips" can be heated and bent a small amount inwards. I attached a magnet…
P
Printables
LedLenser Floating Charge System Car Adapter
LedLenser Floating Charge System Car Adapter https://www.ledlenser.com/de/produkte/zubehoer/floating-charge-system-car-adapter/ Its not identical (scanned) but close to the original. Printed with the flat side on the bed and it prints…
P
Printables
Bicycle Handlebar holder for LedLenser T7 torch
This is my take of a bicycle holder for the popular LedLenser T7 torch. I use it for my comuting bicycle and felt that I might share it. It is customized for a 32mm hanlebar and has no adjustable clamp so you need to shim it in place to…
P
Printables
LedLenser P7 Wallmount with diffuser
My first 3D Design. I'm a beginner, trying to learn everything possible with my Ender 5 Pro. Model is made with MatterControl (Free) This Design is a Wallmount for the LedLenser P7 (p7.2 ?) The Wallmount has a slot for the diffuser, and…
P
Printables
LedLenser repair
LedLenser head flashlight repair part. Fixing the battery holder on my Ledlenser headlamp. The original one just fell apart from wear. Made of PET-G
P
Printables
LedLenser IF2R Charging-Dock
Charging dock for LedLenser IF2R lamp. Printed with PLA and 40% infill.
P
Printables
Mount with Charging for Ledlenser P4R Wurth Flashlight
Features: Designed for the Ledlenser P4R (Wurth version) Charging without removing the flashlight Sturdy construction Compatible with screw mounting or double-sided tape Printing Requirements Printing Technology : FDM Filament : PLA /…
P
Printables
Charging Dock for LedLenser USB Type A Dongle
This adapter keeps the USB type A Dongle from LedLenser standing steady on the table, turning it into a convenient charging dock. Confirmed working with the P5R Core and P7R Core , but should work with diameters up to 30mm. Let me know if…
P
Printables
Camp bed flashlight (ledlenser p2, convoy s2+) and phone compartment
This is a compartment that can be attached to the headboard (square tube 32mm) of a camping bed. I printed it in two parts. Clip in black PLA and compartment in glow in the dark PLA and glued it together with cyanoacrylate glue…
P
Printables
Gridfinity holder Mini chinese LED FLASHLIGHT & LEDLENSER P2R CORE
gridfinity holder for a cheap aliexpress mini flashlight and a LEDLENSER P2R CORE flashlight Alixpress light: aliexpress.com/item/1005006388063970.html
P
Printables
Bike flashlight holder (Ledlenser T7.2 or similar)
First I made a version that is held down entirely by velcro strap, but realized that PETG work great even without a strap, so I made a version that can be held together with a glue. Some might prefer velcro version as it can act as a…
P
Printables
Flashlight Diffuser for Ledlenser P7
37mm diameter diffuser for Ledlenser P7 (P7R excluded), T7 series Print settings: Filament: Translucent filaments. Layer height: 0.3mm Supports: no Perimeters: 2 Scale factors: ±100.6% for PETG was perfect fit, In my case
P
Printables
Snap-Fit: 3M Versaflo Ledlenser Adapter Mining Lamp Bracket
Ledlenser Adapter – Compatible with H8R series headlamps for 3M M-Series Versaflo respirator masks (requires mining lamp bracket). Important: Additional part required – 3M M-940 Mining Lamp Bracket Kit:…
P
Printables
3M Versaflo Ledlenser Adapter Mining Lamp Bracket
Ledlenser Adapter – Compatible with H8R series headlamps for 3M M-Series Versaflo respirator masks (requires mining lamp bracket). Important: Additional part required – 3M M-940 Mining Lamp Bracket Kit:…
P
Printables
Charging cradle for LedLenser P7R
Charging cradle with cable storage space for LedLenser P7R (with magnetic charging adapter) Wrap the USB-cable around the three stands to shorten the cable until it's connected to a USB-power-Adapter. → countersunk screws (3 pieces)…
P
Printables
LedLenser XEO 19R mount for Garmin K-Edge
adapter to mount the XEO 19R onto my bycycle.adapter to mount the XEO 19R onto my bycycle.
P
Printables
Ledlenser Spare Battery Case
A case, with sliding lid that holds a 2 x 21700 Li-ion Ledlenser battery. These batteries are used in the H15R Core & Work and H19R Core & Signature
P
Printables
Gridfinity 1x3 Ledlenser P5 holder
Ledlenser P5 holder for Gridfinity 1x3. Designed in Freecad.
P
Printables
Skadis Ledlenser P7R Stand
This is a simple stand for your LED Lenser P7R. The stand can be mounted to a IKEA SKADIS Wall.
P
Printables
Ledlenser MH7 tri-glide buckle
A replacement buckle for Ledlenser MH7 LED flashlight. Should work with any other similar strap. Tried to model it as close to the original as possible, there are some deviations, feel free to modify it. Printing Instructions Use PETG,…
P
Printables
Würth Ledlenser P7 Rebuild/Upgrade
The files consist of an adaptor for a Convoy 1288 switch , an adaptor for a 16mm LED and finally a slieve for a 18500 LiIon cell. With those parts I was able to put a 10W Cree LED in the good old LEDlenser body. Don't forget to order some…
P
Printables
Ledlenser P5R Flashlight Multiboard Holder
This is a Multiboard holder for a Ledlenser flashlight model P5R. It uses a single press-fit Multiboard peg. I don't know if other Ledlenser models will work with this, but the handle diameter is 22mm for reference. Prints in place…
P
Printables
GoPro adapter for Ledlenser Headlamps
I've made this to mount a Ledlenser HF6R headlamp on a RockRider Expl 500 bicycle helmet by Decathlon. The model is split into two parts to make printing easier and to be able to use two different layer alignment for improved part…
P
Printables
Ledlenser P17 signal cone
This signal cone is 22 cm (~8.5 inches) tall and fits the Ledlenser P17 series flashlights Depending on your printers calibration you might wan't to do some test prints and adjust the scaling in your slicer to get the desired fit. I'd…
P
Printables
LEDLENSER Flashlight Diffuser for P7* with heat exhaust
Yet another Flashlight Diffuser for LEDLENSER P7* flashlights with better heat exhaust. Inspired by P7, P7.2, P7R work lamp led lenser by VikKon. Had some troubles with the LED heat so this diffuser comes with 4 little holes. Instructions…
P
Printables
LEDLenser P7R Core Wandhalterung mit Ladefunktion / wall mount charger
Hallo! Die ursprüngliche Design Idee stammt von: https://www.thingiverse.com/thing:5180316 Wie man unschwer erkennen kann habe ich aber so gut wie alles geändert und die Halterung für die P7R Core angepasst. Die Maße für den Ladestecker…
P
Printables
light cone for Ledlenser P14
A light cone for a Ledlenser P14 flashlight. You can use it as a diffuser or to direct vehicles (marshaller). Due to the opening at the tip you can also illuminate smaller objekts at close range or read a note. There is also a version…
P
Printables
LedLenser Charging Dock
I reverse drew this design of the original charging dock. All the dimensons are correct.
P
Printables
Ledlenser HM10 Helmet Mount
Not commercially available, so I made my own. I used 3M Dual Lock to attach the brackets to the helmet, for a non permanent solution. Ledlenser site: https://ledlenser.com/de/mh10/501513
P
Printables
LedLenser iW4R dc cover
my rubber cover came of my work light so i decided to make a replacement. i would recommend printing with support but if ur overhangs are great maybe u wont need it. it should fit with slight friction to keep it in place.
P
Printables
Ledlenser P7R Tripod Mount ArcaSwiss
Tripod Mount for Ledlenser P7R with a ArcaSwiss compatible platte. Very helpful for taking pictures where more light is needed, for example Macroshots from mushrooms in the woods. It is my first model, if you have ideas to improve it,…
P
Printables
Skadis Holder for Ledlenser Floating Charge System
I wanted to put my Ledlenser P7R to a Ikea Skadis Wall, so i designed two holders to mount them on the Floating Charge System. You need to M4x6mm Inserts and melt them into the holes and two M4x10mm countersunk screws.
P
Printables
light cone for Ledlenser P7QC
A light cone for a Ledlenser P7QC flashlight. You can use it as a diffuser or to direct vehicles (marshaller). Due to the opening at the tip you can also illuminate smaller objekts at close range or read a note. There is also a version…
P
Printables
LedLenser M14 Wandhalter
Wandhalter für eine LedLenser M14 Taschenlampe Remix von Altair: https://www.printables.com/de/model/8658-generic-parametric-flashlight-holder Body der M14: (42mm) Gedruckt mit PTEG - 0.2 - Infill 20%
P
Printables
LedLenser EVO300 Wandhalter
Wandhalter für eine LedLenser EVO300 Taschenlampe Remix von Altair: https://www.printables.com/de/model/8658-generic-parame Body der EVO300: (35.5mm) Gedruckt mit PTEG - 0.2 - Infill 20%
P
Printables
LEDLENSER P5R CORE TORCH CHARGING STATION
LEDLENSER P5R Core torch holder with charger socket. I recommend sponge glue to fix the charger
P
Printables
LEDLENSER modified helmet band clip
Modified helmet band clip for LEDLENSER H7R Work and others.
P
Printables
Ladehalter / Loadingdock Ledlenser P6R Core
Wandhalterung / Loadingdock to mount the loading cable to the wall and store your flashlight.
P
Printables
LEDLENSER MH3 mount for helmet
ledlencer MH3 mount for MTB bike or MX helmet. Using for PEV equipment.
P
Printables
LEDlenser H14R.2 Case
I created this case for my H14R.2 head lamp so it won't accidentally power up inside my pack. The case is part of a set of cases I created for different stuff I use as an event technician. The lamp needs to be twisted 360° against the…
P
Printables
Bontrager Helmetplate for action camera & Ledlenser MH5
Print it on its side to get the clips stronger, using support everywhere. Filament ASA and layer thickness 0.20mm. I used nozzle size 0.4mm. I have a separate file for matching fixture for a Ledlenser MH5 light with flex-brake-bad, an…
P
Printables
Petzl Vortex Helmet Adaptor - LEDlenser H14R.2
I designed this adaptor to my Petzl Vortex helmet so I can mount my LEDlenser H14R.2 to it. It can also be used as a base for designing mounting brackets for all kind of stuff. The parts are connected with M3x20mm sink head screws and…
P
Printables
Signalkegel / Lightcone für LEDLENSER P7R / P7QC
Eignet sich super, um komplette Räume nur mit Taschenlampen auszuleuchten. Gedruckt aus PETG. ABS/ASA funktioniert auch. PLA ist bestimmt möglich, habe ich aber nicht ausprobiert. Material auf den Fotos ist PETG Signalweiß von M4P.…
P
Printables
Ledlenser H connector
I did print the final version on Bambu X1C Rosa3D ASA filament. It fits nicely my petzl helmet and Ledlenser H7RCore head torch. I did fix it with 4mm screws and 3M AFT tape, holes in helmet custom drilled. With ASA I did print it in…
P
Printables
Ledlenser K2 holder
A holder for the Ledlenser K2 torch. The holder attaches snugly to the flat parts on the side of the torch. If you find the holder to not be tight enough, the the "tips" can be heated and bent a small amount inwards. I attached a magnet…
P
Printables
LEDLENSER MH3 mount with GO PRO interface
100% infill, it was designed for ABS, should works with PETG or ASA https://youtube.com/shorts/P8ExItbauA4?si=zwLknvXHnN6BEFN2
P
Printables
Skadis Ledlenser Halter
Ich habe mal 2 Simple Halterungen für das Skadis System entworfen, für die Ledlendser: P7R P6R-Core Gedruckt mit 15%infill Material ist frei wählbar einmal mit Durchmesser 35,5 und einmal mit 38mm viel Spaß damit
P
Printables
LEDLenser Halterung P7core P6core
Halterung Für LED Lenser Taschenlampen P6 und P7 Core Funktioniert bei anderen mit einen Griffdurchmesser von 21,50 mm
P
Printables
Ledlenser MH5 LED holder
The Ledlenser MH5 LED Holder is a replacement part for the Ledlenser MH5 headlamp. It securely holds the LED bulb in place, ensuring optimal performance and longevity. It is recommended to print this part from a filament that withstands…
P
Printables
LEDLenser P3R Halterung für Fahrradlenker
Eine einfache halterung um einen LED Lenser P3R als Fahrradlicht zu verwenden. Zusätzlich wird noch ein Gummiband benötigt um die Klemme an dem Lenker anzubringen. Für andere Taschenlampen kann das Modell sicherlich auch noch skaliert…
P
Printables
LEDLenser P3R Rucksackhalterung
Hierbei handelt es sich um eine Halterung um ein LED Lenser P3R an Riemen eines Rucksacks zu befestigen. Die Halterung hat eine Klemme in die man den LED Lenser einknipsen kann und dann einfach an einem Riemen an Rucksäcken befestigen…
P
Printables
Backpack Strap flashlight adapter for ledlenser saftey bag
This is a simple adapter for the Ledlenser safety bag so that it can be hung from a backpack strap infill 100% for sturdiness Print Settings Printer Brand: Creality Printer: Ender 3 **Rafts:** No Supports: No **Resolution:** 200 Infill:…
P
Printables
LEDLENSER Battery Charger Akku Ladegerät H7R.2, iH7R CRI
As there is no chargin cradle available to charge the battery of an LEDLENSER H7R.2, iH7R or CRI battery, I built my own. This one can be handled with every li-ion chager. edit 04.05.2020: I added a "storage box" to prevent leakage…