480 models
UPDATE!!!! Oct. 2020 I change the case a little bit and the upper and lower mount. If you print the old case and your mounts doesnt fit, you only print the mounts new. then it works. Sorry You need 2 x upper mount and 1 x lower mount.…
Designed this simple cover for Meanwell LRS-75-12 model but should work for 24V model as well. Fast and easy print. Protects the terminals from the top, but shouldn't interfere with the wires themselves. You can print it at 0.3 (Draft)…
For providing A/C input cover and D/C output cover for a Meanwell SE-600-24 (or other SE-600 series) power supply. Designed to use the following IEC320 power entry: https://www.mouser.com/ProductDetail/161-PX0575-15-63 And the following…
I needed a more cat-safe cover for my Meanwell LRS-100 power-supply which I use to power my ambient light behind the TV. Since the cats like to stroll there, using it without any cover was a no-go, so I created this. Print settings:…
Requires: 2x din rail clip: https://www.printables.com/model/161740-din-rail-clip 4x DIN 912 M3x10 4x DIN 934 M3 4x DIN 912 M4x10 4x DIN 934 M4
Requires: 2x din rail clip: https://www.printables.com/model/161740-din-rail-clip 8x DIN 912 M3x10 8x DIN 934 M3
Updates 03/2022: Changed two screw holes on the switch side part to slotted holes (v2.1). This allows you to tune the fit and tension during assembly. 04/2021: Added a "MIRRORED" version, which allows you to flip the PSU around and have…
A PSU Fan cover/silencer for the Creality Ender 3 Pro / Meanwell LRS-350-24 PSU This model was designed to print the models separately in different colors and fit the embossed letters into the debossed fan cover. If the embossed “GHOST”…
IMPORTANT : this model is about 20mm longer than the ender 3v2 print bed. So you will need to print this on a different machine or alter the model before printing. If you don't want to do that you can take a look at my original version…
Upgrade your power supply fan to 92mm and make it SILENT! -Use a 24V fan or use buck converter to step down to 12V: https://a.co/d/c0GqEZc 92MM fan: https://a.co/d/44JLwyI Black is ground, Yellow is positive. You don't need the other two…
This is a simple cover for the Meanwell LRS-350 series of power supplies. It has a mounting hole for an IEC-14 power socket (commonly available from Amazon) and covers the voltage terminals of the power supplies. Print instructions This…
This print is helpful when mounting a Mean Well LRS-100-5 5v power supply to a DIN rail. This power supply is handy for a variety of applications including 3D Printers like Voron, RatRig, HevORT, and others. Secure the power supply to the…
This is an adapter to hang the Meanwell LRS-25-5 onto the DIN rail. I designed it (remixed an classical clamp design by Fabian) for my RatRig V-Core3 400mm. Print as shown in picture and it not require supports. I designed it for some M3…
Updated version can be found here: https://www.printables.com/model/201359-ender-3-v2-external-electronics-box-meanwell-psu-a Created electronics box for the MeanWell PSU and Ender 3 V2 motherboard so I could keep it outside of my…
Meanwell LRS-350 Mount + DIN rail mount. Coming with additional DIN rail mount (hole space 46mm). Mounting on two mounts with M4x8 hex screw. You can mount it on DIN rail or through hole to some base whatever you like :) Screw is standard…
11.03.2022 - Updated positions of bores for both endcaps/ turned powerswitch (V2) This brackets fits to Meanwell UHP-350-24V power supply in combination with Ratrig V-Minion 3D Printer.
DIN bracket for Meanwell LRS-350 -- DIN Rail Bracket https://www.printables.com/model/97222-din-rail-bracket By Fabian I modified to accept the 4mm SHCS - the holes are not exact but it works on the LRS-350 with some patience.
Center hole distance 55mm
Mounting bracket LEFT and RIGHT for two Meanwell LRS200 or LRS350 Power Supply. Use M4 Bolts, Flat and Lock Washers. Print flat with large section on bed. I also design a similar kit for power supplies with dissimilar width (LRS200 or 350…
As I needed to mount my Meanwell LRS-150-48 PSU to my VCore3 printer, I designed this mount adapter. It doesn'r require supports of printed as seen in slicer pics. You need 3x M3 6mm BHCS bolts and one M3 heat-insert (best with 4.6mm OD…
This is a Meanwell LRS/RSP Mount for my DIN Rail Bracket. You can find the bracket here ! For the DIN Rail Bracket Mount you need M3 countersunk screws. For the Meanwell Power Supply you need M4 screws. 2023-03-16: - Bracket holes…
A small cover for the wiring terminals of the Meanwell RSP-320 power supply. Edit 08-2022: Thanks nosstromOS for confirming the compatibility with the LRS-200 power supply. Thanks Keith Chong for confirming the compatibility with the…
Fits Mean Well LRS 350 PSU upgrade for SOVOL SV06.
This is a C-LIN SSR 40A480VAC Mount for my DIN Rail Bracket. You can find the bracket here ! For the Mount you need M3 screws and M3x4 or M3x6 Heat Inserts. For the DIN Rail Bracket Mount you need M3 countersunk screws. “Single” and…
5 Ruthex M3 heat inserts are needed Print Settings Printer: Voron 2.4 Rafts: No Supports: No Resolution: 0.20 Infill: 25 Filament: ESUN ABS+ ABS Category: Electronics
Wanted to have my PSU mounted* directly to my Rook using original MK1 parts. It makes it easier to move around even though it becomes a bit heavier. I've only made a version that mounts on the right side, but I can make a left version if…
Requires some screws in order to assemble the fixture. Clips could be mounted either horizontally or vertically for different PSU orientation. For horizontal orientation one can drill more holes and print more clips for more stability
The main body has areas that can be glued and the the pi becomes somewhat structural once installed without the covers. The electronics cover has new little tabs for m3x12 or longer screws to hold it together.
Feb 10, 2024 : STEP file added. -- Print details: Material: PLA, PETG, ABS, or any filament you like. I use Overture PETG Black. layer height: 0.20mm Supports: You only need support for the big hole. I recommend to use Paint-on supports.…
Hardware needed to install Cap/Button Screw M4x6 - 8pcs (Screw on PSU) Cap/Button Screw M5x10 - 2pcs T Slot Nut 2020 M5 - 2pcs Factory power supply mount screws - 2pcs Print as oriented in the slicer picture. Print 2 brackets and one…
The stock PSU on my Creality Ender-3 needed to be replaced, so I swapped in a Meanwell LRS-350-24. I couldn't find a cover that quite fit the Ender-3's arrangement, so I created this. You will likely have to bend the terminals/wires for…
VZBot electronics mounts on din rail: Orange Pi 3LTS BTT Octopus PRO with 5160 Only BTT Octopus PRO PSU Meanwell RD35 DINrail clip You'll need screws and nuts M3
DIN 35mm brackets for Meanwell LRS 150-24 power supply unit Easy to print and use DIN 35mm brackets for Meanwell LRS 150-24 power supply unit. BOM (Bill of Materials) Mechanical parts QTY Bolts: M3x8 SHCS | Source: [Link] — or — M3x8 BHCS…
Hardware needed to install Cap/Button Screw M4x6 - 8pcs (Screw on PSU) Cap/Button Screw M5x10 - 2pcs T Slot Nut 2020 M5 - 2pcs Cap/Button Screw M4x30 - 1pcs (M4 Washer maybe needed) Print Settings Material: PETG Infill: 30% Perimeter: 3…
…Please be sure to hit like & post a make, I'd love to see your prints! NO more Wobbly RPi PSU's on a single clip for you! The stock clip is good but allows the PSU to wobble about way too much! Fix this issue with this super simple but…
A quite universal (requires 4xM4x10 bolts and 4xM4 screws) mount for Meanwell-LRS-350 series PSU. Holding screws are hidden within the mount for hers&your pleasure (aesthetic lvl over 9000) in a pocket slanted 40 degrees. I'd suggest at…
Modification of the Original part deleting the silly power plug hole. Just unhook the PSU cable from the fan and route it through the fan hole. You should shorten the cable and reuse the sleeve from the Original fan anyway for safety. I…
FR Protège bornier pour alimentation Meanwell LRS-350-24. Il est clipsable pour rester en place. Un orifice permet d'insérer un petit tube acrylique (3 mm de diamètre) pour que le voyant M/A se voit de l'extérieur.…
This is a remix of DIN clips for Meanwell LRS 200 PSU by neon.blue
Made the walls thinner to save filament and removed the text on the top as i got some bad looks for the double thunderbolt… Like the original model, it is fixed with one short M3 screw.
Improved the strength of the tab. In the comparison photos (with two parts side by side), the part on the left is this model while the one on the right is the original design I modified from. Printed in eSUN Fire Engine Red PETG with 0.2…
Voron style, simple DIN rail mount for meanwell PSU (other brands with 50mm threads space work's too) Printed from ASA but propably all filament types will be good
I needed some extra power in my Voron V2.4, so I heavily modified the original from the great people at Voron Design and tested it. I'd send pictures but I really don't want to move my printer around and re-tune. ;-) Heatset insert…
4 copies of the bracket can be used (be sure to mirror 2 when printing) or use 2 copies of the bracket with the strap if you are using some covering for the terminal side of the PSU. Brackets have a small lip to prevent PSU from sliding.…
This is a simple bracket to offset the PSU off from the Z-axis upright, making way for a 2nd lead screw. It mounts to the 4040 extrusion using M4 screws and T-nuts. Print it with the side which faces the PSU facing down on the bed. No…
This is an enclosure designed to fit closely to a Meanwell LRS-100-5 power supply, and to house a NodeMCU Base PCB. My objective was to have a neat, all-in-one enclosure for all I need to run the excellent WLED "Neopixel" addressable LED…
Meanwell LRS-350 enclosure for bear 2.1 frame with additional RS-25 power block. This parts can be usefull if you want to power your Raspberry or led strip lights with different voltage than the main LRS block has.…
BEEFY DIN RAIL MOUNTS These are Completely Overbuilt! They Require 1 purchased part - Link Below I made these mounts to solve the below issues from the Voron 2.4 r1. BOM STL files Will work on any 35mm Din Rail Mounted Setup These are…
About This is a useful enclosure for a Meanwell LRS-50-5 PSU Power Supply. It serves two main purposes: Provides increased safety and protection, by adding an insulating cover (with ventilation holes) and leaving only the minimum required…
Introduction This model incorporates design elements from https://www.thingiverse.com/thing:3082178 which was designed for the discontinued Meanwell NES-350-24 . I like the design for its simplicity, rear-facing AC/Mains receptacle, and…
This is a small cover designed to cover the terminals of the LRS-100 power supply to prevent contact with fingers and tools when in use. (Confirmed on an LRS-100-5, but likely works with others as well.) This has been remixed so that the…
This is a 3D printed mount to allow a Meanwell UHP-200 power supply to be attached to a DIN rail. Requires 2x pcb_din_clip_v2 from the Voron Trident. BOM 2x pcb_din_clip_v2 (printed) 4x M3 Threaded Heat Set (M3x5x4) 4x M2 x 10…
About Meanwell LRS-350-24 PSU Case This is DIN rail mountable (and standalone) case with protection cover for Meanwell LRS-350-24 PSU. This case is designed primarily as an accessory for The RIG — a DIY workstation stand for testing…
Fix for gaps in the original model through fusion 360
The official Dual-Z upgrade kit requires you to relocate the PSU to the back. And as I wanted to replace the old PSU with the LRS-350-24 PSU from Meanwell, this asked for a redesign (o; It is advisable to have a protective ground cable…
I had a backup Meanwell NES-350-24 power supply sitting for over a year incase my stock MK3 power supply died. Well it finally failed on me and I wasn't too thrilled with any cases I found online so I decided to design my own. It takes a…
This version allows the LRS 100 series to be rotated 90º & -90º or in its original orientation. It also improves print-ability of the original holes. You only insert the heatset inserts you need for the orientation you want. Additionally,…
In order to avoid accidental contact with the terminals on a Meanwell power supply, I've put together a quick cover that clips over top of the terminals once everything is set up. Two versions are provided: a longer one for LRS-350 power…
This is an adapter to hang the Meanwell LRS-200-24 onto the DIN rail of a RatRig V-Core3 400mm. It should be printed twice, one mirrored (see picture). It doesn't require supports. It is designed for the DIN rail distance (137.5mm)…
Needed to make covers for terminals and mounting brackets so I made a simple model. PSU looked good enough to share. Still working on the terminal covers and mounting brackets. Will upload those when they're finished.
Cover for Meanwell Powersupply it keeps little (and big) fingers away from shocking experiences safe and allows you to hang the PSU on a board. Print instructions Category: Electronics Print Settings Printer: Mendel90 Rafts: No Supports:…
Case for MeanWell RS-25-xx switching power supply series with on-off switch and fuse (Schurter or equivalent). Print instructions Included rsdoc 3D source is easily modifiable, corner mount presented is designed for Ikea Lack tables.…
Noctua NF-A9-14 90mm fan cover for Meanwell PSU. Although intermittent, the stock fan on the Meanwell LRS 350W is loud when running. Switching it out for a 90mm noctua fan significantly reduced the fan noise. I've reduced the hex mesh…
This is a remix Meanwell UHP-350-24V power supply mount designed to attach to the Ratrig V-Minion 3D Printer from JP3d . These brackets fit the Meanwell UHP-350-24V power supply in combination with the XP Power FGSM inlet for Ratrig…
Safely stack the Meanwell Power supplies. This was originally created to stack power supplies in a CG1500 box. The addition of a terminal cover to help prevent fingers or objects accidentally touching live terminals (does not account for…
Why? I needed a slimline mounting solution to mount a Meanwell LRS 100-5 to a 35mm DIN Rail, printable on the limited space of a Voron 0.1 Features: Uses the PSU Brackets of the Voron Trident, privided below Provides a 4 point…
Why? I needed a slimline mounting solution to mount a Meanwell LRS 150-48 to a 35mm DIN Rail, printable on the limited space of a Voron 0.1 Features: Uses the PSU Brackets of the Voron Trident, privided below Two part design to be…
I liked the shape and size of JP3D's model, but the mounting holes were giving me some troubles. When I removed the screw for the AC end of the power supply(PS), an L-shaped clamp came loose inside the PS. So I decided to change the…
Based on the the updated version, I used Tinkercad to disassemble and customize the case into individually printable parts. It is held together with hot melt inserts and M3x6mm screws. For the support strut 2x M3x8mm are needed. The fans…
Printed in ABS / ASA without support.
The Mean Well LRS-600-24 is using a 12V fan, so it can be easily replaced with a quiet one, like a Noctua (you'll need an adapter for the JST PH 2.54 2PIN connectors) Two possibilities: LRS-600-24.STL : the fan is INSIDE (with grid). You…
I created a safety bracket for the Meanwell LRS-150-48 PSU which protects the power terminals from being touched by mistake.
This bracket is used to mount a power supply to a printer base. My power supply is a MeanWell brand but I believe that the mounting holes are the same on these style of power supplies. Four of these brackets provide an easy way to mount…
This is the all in one solution for my CR-10s. This should work with a CR10 as well. I design this power supply and the cast to not need any supports. You will need: 3 - M3 screws and 3 cage nuts Here is the control box:…
Hallo ich wollte mein Meanwell Netzteil leiser haben aber trotzdem die Kühlleistung nicht verlieren. Da wollte ich gleich meinen Noctua NF-R8 benutzen so entschied ich mich für meinen Zaribo dieses Abdeeckung von…
My take on a fan cover for the Ender 3 v2 power supply (MeanWell LRS-350-24) which allows mounting of an 80mm fan on the outside. Additionally I added an easily removable terminal cover, so it's not possible to touch the mains and 24V…
Got sick of opening up the flimsy case of my printer so I decided to make an all-in-one external case for this bundle of components that works great from Amazon: https://www.amazon.com/gp/product/B09MYT45BQ I added the power supply and a…
Really liked the original version of this, but when using the mirrored version you can't use a cable chain, so modified it so that there is a channel for the bed cables and a mount for the cable chain to attach to.
A custom cover I made for my Enderwire mod, but can be used for any application of the LS350. Be aware that there seem to be versions with 24V and 12V fans out there. POWER SUPPLIES ARE VERY DANGEROUS EVEN WHEN NOT CONNECTED TO POWER FOR…
Added version for 60mm fan – I don't have a fan to test this with so please let me know if it all fits correctly Cover for the Meanwell LRS 350-24 (Present in some Ender 3's, all Ender 3 Pro's, V2's and Max's), mounts to the inside of the…
A small cover for the MeanWell RS-50-S (and probably other powersupplies with 5 screw contacts) that protects you from touching the contacts. The cover fots tightly so that it cannot accidently fall down. OpenScad file attached for…
Changes: increased wall thicknesses to 4mm, increased the power supply hole, added zip tie slots for strain relief. See the photo for rough dimensioned changes. F3d file included.
Designed for any power supply with 78mm M3 hole spacing on the back. Can be mirrored in your slicer software if you want to change the direction the power supply will face when mounted on a DIN rail. Originally designed for the Meanwell…
you need M3x10mm screws
a mount to attach the psu to the din rail on the Voron 2.4. The existing din rail fixtures are too loose. BOM: 2 x M4 screw 2 x M3 screw 2 x M3 nuts ( or heat inserts with a D4.2) Din rail clips Fusion360 file attached
Print in Place plastic DIN rail mounts for meanwell (and other) power supplies with 50mm (center to center) hole spacing. Requires two for each power supply. Second one needs to be a mirror of the first (use your slicer to mirror the…
This is a bracket to mount a MeanWell LRS-350 power supply on it's side vertically. I designed this mount to be simple and conscious of the vent holes. The two brackets for one power supply are identical. it has countersunk holes for…
Tired of Hearing your Ender5-Plus sound like a jet engine? do you feel like every day, all you hear is tinnitus ringing in your ear as you sleep? FEAR NOT, for I have blessed you the file and setup you need to do in order to make your PSU…
I installed a new Meanwell LRS-350-24 power supply on my Ender 3 and needed a new mounting case to fit the smaller power supply. Additionally I wanted to connect the Raspberry Pi with a QC 3.0 USB-power supply. These things are for ships,…
Mounting bracket LEFT and RIGHT for two dissimilar width (LRS200 or 350 at the bottom, LRS-600 on top) power supplies. Use M5 Bolts, Flat and Lock Washers. Print flat with large section on bed. I also design a similar kit for two LRS200…
Din Rail Adapter for Meanwell RSP-500 Power Supply
!!!!COMPATIBLE ONLY WITH ENDER 3 PRO (MeanWell LRS-350) PSU!!!! Standard Ender 3 PSU version - https://www.thingiverse.com/thing:4821213 For chassis already cut for ease of print - see remixes section! October 24 Update: Added left sides…
I have created several versions of this case. This evening I realized that somehow this one didn't make it over from Thingiverse. This is the version of the case that I use and that I prefer. I am using it on a Prusa MK3 that has had the…
This is a simple mount for a QuinLED Dig Octa to screw into the sides of a meanwell 600 powersupply. Provides a little spacing between the bottom of the mount and the power supply to make sure heat isn't getting trapped. The V2 model is…
When I built my Voron Zero I was concerned at the ease at which someone could touch the mains voltage terminals on the PSU if the skirts (not supplied in the PiF kits) were missing. Additionally, the finger guard provided didn't feel…
Print in given orientation. Supports needed for the main ‘hole’, I printed using Tree support. Place blockers on the top of other holes, supports not needed there. 3 holes added to the rear for freedom to pass through the 24V power cable.…
I produced this model as I was not happy with the large size of other guards, their flimsiness, or their ability to properly guard the terminals. This model requires an M3 threaded insert (diameter 4-5, length 3-4) and an M3 caphead screw…
need any 18mm screw x 3 i use socket head
Few adjustments to already existing PSU relocation model. Requires 2 m3 inserts.
This alternate case cover allows you to use a 120MM fan with your Meanwell LRS-350 case. It includes inset text for easy identification of terminals. Requires M3 hex nuts and M3x10mm screws close up, and a 120MM fan. I used a Noctua…
