Counting matching models…
Use double-sided tape or glue to fasten it down. It presses against the ball so the tape/glue is just needed to prevent it from falling off sideways and doesn't need to be very strong. I printed it without supports and had no issues. PLA…
Simple way to anchor or hook things inside your Muli cargo basket. Prints well without supports and it's plenty sturdy in PETG with 100% infill. You will also need: 1x M4 nut (ideally self-locking) M4 x 8 mm screw (ideally with washer)
Sturdier design of the locking rod holder for Muli. Holds the locking rod on the side of the basket when not in use so it won't rattle around.
I wanted to make this remix to make consistent colour changes on this ruler for my partner. Thought it may come in handy for others who don't have the patience, time or knowledge to slice manually. I printed this with default PLA…
Remix of Narsil bookmark by Lex ( lexinator8 ). This version has been split into multiple parts to allow for easy color printing. The side inlays have also been realigned so they are now centered on the crossbar for a more balanced…
This is a remix of the Multiboard Flush Snap with a small thread hole.
I remixed the player pick axe and hoe tokens for the SDV board game for Multi color printing.
This allows you to mount your Hamulight L2046 power supply wherever you need it instead of having to rely on 3M tape. It will print fine without supports with “mounting ears” in the air because I used counterbore bridges and suitable…
Made this thing in Tinkercad after the third lince detached. The model has a small hole where the two parts connect, which you can see atleast when slicing in Bambu. It doesn't show in Tinkercad, so I decided to leave it as is, since it…
This basic foot for the IKEA MULIG drying rack is designed to counteract the inherent instability of the rack's design. While the original rack may band and rock from side to side under the weight of clothes due to its structural…
Hello Community, Here is my profile for the Orca Slicer. I have used my Creality K2 Plus for over 300 hours and modified the basic profile to this version. This profile is optimized for multicolor printing or printing with PETG/PLA. The…
This is a center cap for a Formuling steering wheel with a 78mm hole and approximately 5mm plate thickness. It features a 1970 VW logo, which can be printed in a second color if desired. TPU is recommended, otherwise you may not be able…
Print the feet in TPU. Print the clip in anything, like PLA.
Printed with strength settings using PLA, the "Thick Boy" is probably overkill, as the thinner one is definitely strong enough to support the weight of the circular saw. The length of the gap for the hook is around 133.5mm, so as long as…
Small hook for hanging clothes and other light items on the IKEA Mulig clothes rack. If you have trouble clipping the hook onto the rail, you might have to reduce infill % to allow for more flexibility.
Mulita es un robot educativo diseñado para aprender jugando. Está pensado para ser fácil de armar y de utilizar en contextos educativos. Además, se lo desarrolló pensando en que sea adaptado según la creatividad de quien lo use. Esta es a…
These are USB cable organizers designed to be wall mounted, either using #8 screws, 3M Command Strips or double sided tape. The 6 place cable holder has 4 places for thicker cables (5mm openings) and 2 for smaller ones (4mm openings). The…
I designed this wall mount so I can hang the IKEA MULIG rack on the wall and still use it for drying clothes without taking it down. When I do small laundry loads, I can hang things directly on it. I also made a right-angle hinge that…
Use double-sided tape or glue to fasten it down. It presses against the ball so the tape/glue is just needed to prevent it from falling off sideways and doesn't need to be very strong. I printed it without supports and had no issues. PLA…
I noticed on my Core one that you can already see it on the inside wall where you often touch it with the sheet, which unfortunately cannot be avoided. That's why I designed this protective cover, which can be easily attached with…
THIS IS OUT DATED GO TO THE NEW VERSION https://www.thingiverse.com/thing:4095702 The FDL-3 was originally designed by Project FDL https://www.projectfdl.com Please download the ZIP File its organized This is designed for mulitcolor…
Ikea Mulig drying rack lift anti-slide lock. I experienced this when I lifted the rack around. This lock keeps the rack locked when it is lifted, preventing the drying rack from sliding and wrinkling the clothes.
When folding up the basket of the muli cargo bike, the locking rods need a place to go. With this print you can fix them to the sides of the basket. The bottom peg keeps the holders from rotating. For fixing the holders to the basket you…
This model has two parts. One is the main holder, and the other one is the “nail” to which interfaces with the Multiboard octagons.
Remix of the sock hanger for the Ikea Mulig drying rack to use less material
Credit goes to Kurtle Design for the concept of the original aesthetic backpack hanger, and 8Complex for his clever remix. My need is to display handbags in my wife's dressing room on a dedicated IKEA MULIG clothes bar. So I redesigned…
Settings: all body of one text are mostly named the same so you can select them to change the color PLA works perfekt! Happy printing!
Wer sich selbst eine Arretierstange für sein Muli bauen möchte, kann die beiden Enden nutzen. Am besten man druckt sie liegend um die Stabilität zu gewährleisten. Zum Selbstbau benötigt ihr ein Rundrohr mit 20mm Durchmesser aus Alu oder…
Wer sich selbst eine Arretierstange für sein Muli bauen möchte, kann die beiden Enden nutzen. Am besten man druckt sie liegend um die Stabilität zu gewährleisten. Zum Selbstbau benötigt ihr ein Rundrohr mit 20mm Durchmesser aus Alu oder…
I designed this little gadget to fix a rod of the IKEA MULIG drying rack that had come unsoldered from the frame. Printed in TPU, the result looks good; I’ve mounted it on the drying rack for several months now, and it seems to withstand…
Simple way to anchor or hook things inside your Muli cargo basket. Prints well without supports and it's plenty sturdy in PETG with 100% infill. You will also need: 1x M4 nut (ideally self-locking) M4 x 8 mm screw (ideally with washer)
Sturdier design of the locking rod holder for Muli. Holds the locking rod on the side of the basket when not in use so it won't rattle around.
My 30 Years nicely stored Formuling Steering Wheel fell apart like Dracula in the Sunlight when i touched it. Then i consulted the Internet for an replacement …… Nope. All the centerpieces are torn, desintegrated and crumbled. I got a…
I wanted to make this remix to make consistent colour changes on this ruler for my partner. Thought it may come in handy for others who don't have the patience, time or knowledge to slice manually. I printed this with default PLA…
Remix of Narsil bookmark by Lex ( lexinator8 ). This version has been split into multiple parts to allow for easy color printing. The side inlays have also been realigned so they are now centered on the crossbar for a more balanced…
This is a remix of the Multiboard Flush Snap with a small thread hole.
A quick print that saves space on your drying rack.
Printables cover for the attaching to the wall parts. This is a cover with the Printables logo for the connecting parts and screws. Easy to print in two colors, you don´t need the Multi-Material-Unit My printing settings: Filament: PETG…
Shelf for your EDC with sturdy hook for a backpack. I use it for my phone and wallet. I hang my backpack on the hook, even when its packed. Its not only neat, but it is actually easier to pack and unpack it, while hanging. If you don't…
This is a Remix of the popular "Sock Clips for Drying Rack" by lundiplutzmus . It is modified to fit for the IKEA MULIG drying rack.
I remixed the player pick axe and hoe tokens for the SDV board game for Multi color printing.
For the holder and pegs, no supports are needed at all. U need: - 4x M3x8mm (10, or 12mm prob also alright) - 4x M3 Heated inserts - 1x Multimeter Holder Mount - 4x peg I printed everything in black PETG Filament.
Wall mount for mulinex optitouch Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 200 Infill: 15 Filament: kexcelled PLA blue Notes: print up side down Category: Kitchen & Dining
Made for Mulinex drip coffee maker, but maybe it works with other coffee makers.
I've designed this from the instructions from a friend who has a son with Autism. I hope this can be useful to other people. You'll need to print it twice and then put few drops of glue in the middle before joining them. Make sure you…
A fun digital camo pot that can be printed in either single or multicolor. requires no supports
Update: I found this to be very unstable and it eventually snapped, the mounting method wasn't good enough, should have bolted it on or something, I no longer use my Mulig so will not be updating this. Put a shelf atop your Ikea Mulig.…
Update 20/1/19: I have added a version without the hinge as mine broke after about a month or two, probably as it had to be printed in a certain orientation for the hinge, the non hinge version should be printed in the orientation shown.…
A replacement shelf hook for IKEA MULIG clothes drying rack . Print with supports everywhere, lying on its side (see photos). Make it solid by setting 100% infill, or increase perimeters enough to fill it. 0.10 - 0.15 layer height works…
Please give this a like if you find it useful or just like the Idea! This mask can be used for anything such as a remote ventilation unit or cosplay. Don't depend on it to save your life, it was something I did to learn the ins and outs…
My vacuum robot gets stuck on the stand of the Ikea laundry rack. This printed addition prevents the robot from driving up the stand of the laundry rack and getting stuck there.
The nativity card kit is a remix for multicolor printing. The baby jesus, words, mary and joseph, sheep, donkey, and stable are all separate so you can print easily to change out the wording, or remove the animals if wanted, and set all…
The reindeer card kit is a remix for multicolor printing. The inner ears, fur, mount, nose and words are all separate so you can print easily change out the wording, or remove portions if wanted, and set all the colors. When putting the…
A stronger shelf hook for the IKEA Mulig clothes drying rack. The rack arrived with one hook broken so I modeled it and added some extra support to improve its strength. I also included the original version in the files. You can probably…
very easy to print and a real eyecatcher on your desk! printed in two colors print settings: 0.2mm layerheight no infill PLA 5 Walls no brim needed if printbed has good adhesion --- a tip is always welcomed =)
I just painted the original model for AMS or other multi-colour printers (or change it by hand, if you are hard-core ;-)) Make sure to flush black filament longer or you will get grey print lines over the whole model (see picture)! .1mm…
This is a Remix of my USB cable organizer meant to be wall mounted. This version is designed for thinner USB cables, with holes that are 4mm wide (the original model has 5mm holes). Similar to the original models, this one also has…
This is a Remix of my USB cable organizer meant to be wall mounted. This version is designed to support both normal sized and also thinner USB cables (in different slots), with holes that are 4mm wide and some that are 5mm wide. Similar…
Print this four times and attach them to your MULIG drying racks legs with super glue to prevent scatching your floor. I recommend printing with 100% infill to get maximum wear resistance Just to be sure ( in case Ikea has changed the…
These printable hooks are designed to make your IKEA Mulig clothes rack even more useful. Snap them onto the clothing rack and to have a dedicated hook for coat-hangers. They come in two sizes, one for 5mm and one for 7mm width clothes…
Zestaw łączników do połączenia 2 wieszkaów MULIG stojących obok siebie w celu poprawy stabilności (wyeliminuje to chwianie się wieszaków). W moim zastosowaniu użyłem 2 komplety do łączenia wieszaków . Łącznik pasuje do siebie po obrocie o…
Introducing the innovative 3D model for a support stand designed specifically for Ikea's Mulig clothes drying rack. Are you tired of the wobbly legs and loose screws of your Mulig clothes drying rack? Look no further! We have the perfect…
I have one IKEA MULIG Clothes bar that I’m not utilizing anymore, so I had this idea to convert it to a spool storage. Remixed too parts together and adjusted the necessary sizes for the snap in clip and used a $1 Wooden Broom Handle…
The original design was only for the side of the bar with 17mm OD and it will fit perfectly, I remixed it to fit also 13mm side. Print on side without support, I used PLA but PETG would have been a better choose
Testcube for mk3s with mmu I also use the test for the different shrouds - you can see from the sphere how even the air distribution is
The model is a remix created from scratch with FreeCAD. The logo part is printed separately and can just put into the catch, after you have removed the supports (it may take some time). I have used a paper cutter and pliers to remove the…
Would appreciate your make, a like and/or voting ;-) The wonderful Muli cycle carrier bike (https://muli-cycles.de/de/bikes/motor) has one weak point. When the bike is set out to rain/ wet weather-conditions, water tends to stay in the…
The IKEA MULIG drying rack has some sharp feet which can scratch the floor. So I made this protective feet for it. As a bonus the feet also act as anti-slip feet. Print them in TPU or other soft material. Dont forget to print 4 pieces.
3D Model of Clothes Rack Stopper Compatible with - IKEA MULIG (Article Number 601.794.34) Hack for IKEA product to improve user experience Download: includes STL files for 3D printing, 1 instructions PDF Additive manufacturing model…
A sturdy hook for the IKEA MULIG drying tower. I use this hook to hang a basket with clothes pegs. I would suggest printing this in PETG, as this is more flexible than PLA. I've printed it in PLA, and the hook partially snapped when…
I did not include any way of locking it in place in the design, so to not have to modify the original bit itself, I decided to just drill a small hole in the bottom through the bin into this insert and threaded a M2.5 bolt in place. This…
There's a dual mount and tri-mount to make it easy to test different action cameras side-by-side.
This allows you to mount your Hamulight L2046 power supply wherever you need it instead of having to rely on 3M tape. It will print fine without supports with “mounting ears” in the air because I used counterbore bridges and suitable…
Materials: EMOS_BOX_BASE_V2 - PLA EMOS_BOX_COVER_V1 - PLA EMOS_BOX_LEG_V1 - PLA EMOS_BOX_LOCKER_V1 - TPU EMOS_BOX_PASEK_V1 - TPU Non Printed parts: Screw M2x10 4x Screw M2x16 2x Box inner dimmesion: 138x73x40
The secondary flag of this earring can be in a different color than the primary. It has to be glued into place. It looks really good with a colorful transparent filament for the secondary flag when light is shining through (on the second…
Remove the legs and use the top part hanging from the wall/roof
The primary flag of this earring can be in a different color than the secondary and the frame. It has to be glued into place. It looks really good with a colorful transparent filament for the primary flag when light is shining through.…
I was in need of additional hooks for my IKEA Mulig drying rack. I didn't like any of the options out there and ended up making my own version that has a large hook section.
Hello, this is a casing for the Bside ADMS7 Smart Multimeter. This can be resized to fit any Bside. Enjoy...Cheers Category: Electronics
A nice small project with some moving parts and a nice model to show what is possible with your 3D printer. You dont need to press this clip closure to open it, only turn the knob 45 degrees to the right (this releases the inner part) and…
A simple attachment to enlarge the standard stoppers. So that nothing can fall off when browsing. Prints easy without support and 15% infill. Update 04.04.2025 V2 is now scalled in millimeters and not meters.
A part for installing wheels under IKEA Mulig shelf system, might also work with other Mulig series pieces. Works with M6 bolts and nuts, you'll need 4 sets of bolts & nuts for 1 printed part and 4 printed parts for a shelf. Print…
Made this thing in Tinkercad after the third lince detached. The model has a small hole where the two parts connect, which you can see atleast when slicing in Bambu. It doesn't show in Tinkercad, so I decided to leave it as is, since it…
Yes you did read the title correctly…😉 The design gave me the idea on how to feed the squeeze treats to multiple cats. Usually the missus and I take two cats each and feed by hand but that is still difficult (with eager cats). With this…
Groundplate for Patches or Stickers to click on the Basket of a Cargobike (Muli) Printet with PLA No Supports
